library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
   the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
   the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
   board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
   which improperly uses an evaluation board's board number and breaks board
   detection at runtime.  This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus.  Note that rman_[sg]et_virtual for IO
   ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
   structures where possible (it would be advisable to use the Simple Executive
   API to set the PIO mode, too, but that is not done presently.)  Also use
   structures from FreeBSD's ATA layer rather than structures copied from
   Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
   and writes to 64-bit addresses and use its macros for various device
   addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
   Cavium-provided code originally written for Linux.  Also make it use the
   same simplified test that the Simple Executive and Linux both use rather
   than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
   to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
   the kernel, rather than assuming we know which addresses we can steal.
   NB: This may reduce the amount of RAM the kernel reports you as having if
       you are leaving large temporary allocations made by U-Boot allocated
       when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux.  This changes
   Ethernet interface naming from rgmxN to octeN.  The new driver has vast
   improvements over the old one, both in performance and functionality, but
   does still have some features which have not been ported entirely and there
   may be unimplemented code that can be hit in everyday use.  I will make
   every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
   random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
   them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
   Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
   executive-config.h or cvmx-config.h.  In the future we may want to
   revert part of these changes and supply executive-config.h and
   cvmx-config.h and access to the options contained in those files via
   kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
   of the USB PID.

   same time.
o) Remove some unused trivial uart functions from octeon_machdep now that the
   uart part is fully working and they are unused.
o) Use __func__ instead of __FUNCTION__.
o) Use intr_*() instead of other routines that do the same thing.
o) Remove some duplicate printfs from the Octeon port, as well as duplicate
   setting of Maxmem.
o) Use the right frequency divider on Octeon.
o) Use PCPU_GET(cpuid) consistently to get the cpuid of the running core.
o) Remove some unused macros in the Octeon port.
o) Use mips_sync() around use of the global dpcpu, whose value may not be
   visible to APs at first.
o) When loading the first thread's stack, use macros to make the code correct
   for n64 as well.
o) Remove stub, do-nothing FAU init/enable/disable functions from the RGMX
   driver.

   pointer, rather than octeon_fpa_alloc.
o) Report half duplex status properly.
o) Do not unconditionally update the last known link status in the softc.  If
   report_link isn't set, when octeon_rgmx_config_speed is called the first
   time it will tell the driver (essentially) that we have already marked the
   interface up.  Likewise, don't change media speed and duplex if only the
   link status is at issue. [1]
o) Remove manual changing of link state and let octeon_rgmx_config_speed do the
   heavy lifting. [1]

Reviewed by:	[1] imp
Sponsored by:	Packet Forensics

o) Properly configure the CAM to handle IFF_PROMISC and note where IFF_ALLMULTI
   handling would go if we didn't already force the NIC to receive all
   multicast traffic.

Reviewed by:	imp
Sponsored by:	Packet Forensics

o) Inline octeon_rgmx_mark_ready into octeon_rgmx_init.
o) Add a media status handler that reports link and media status.
o) Set link state when if_init is called.
o) Remove some printfs related to driver state changes.
o) Remove some gratuitous comments.

Reviewed by:	imp
Sponsored by:	Packet Forensics

statements unreachable and seems to be wrong.  Fixes detection of the number
of ports available on some models.

Sponsored by:	Packet Forensics

lacking a copyright/license statement.  All these files were in the
Cavium FreeBSD source drop and appear to be written by Cavium (some
are nearly verbatim copies of files from the cnusers' 1.9.0 SDK, which
also uses this copyright).

enabled for debugging.  This should be turned off before we release,
but we need it for the moment.