Whitespace change only. Wrap paragraphs.

1 files changed, 64 insertions, 53 deletions

diff --git a/en_US.ISO8859-1/books/handbook/multimedia/chapter.sgml b/en_US.ISO8859-1/books/handbook/multimedia/chapter.sgml
index 36b5d05984..655bf25f3c 100644
--- a/en_US.ISO8859-1/books/handbook/multimedia/chapter.sgml
+++ b/en_US.ISO8859-1/books/handbook/multimedia/chapter.sgml
@@ -57,10 +57,10 @@
     <indexterm><primary>sound cards</primary></indexterm>
     <para>Before you begin, you should know the model of the card you
       have, the chip it uses, and whether it is a PCI or ISA card.
-      FreeBSD supports a wide variety of both PCI and ISA cards.  If you
-      do not see your card in the following list, check the &man.pcm.4;
-      manual page.  This is not a complete list; however, it does list
-      some of the most common cards.</para>
+      FreeBSD supports a wide variety of both PCI and ISA cards.  If
+      you do not see your card in the following list, check the
+      &man.pcm.4; manual page.  This is not a complete list; however,
+      it does list some of the most common cards.</para>
 
     <itemizedlist>
       <listitem>
@@ -166,8 +166,8 @@ device sbc0 at isa? port 0x220 irq 5 drq 1 flags 0x15</programlisting>
       <programlisting>device pcm
 device gusc</programlisting>
 
-      <para>to your kernel configuration file.  If you have a non-PnP ISA card, you will
-	need to add:</para>
+      <para>to your kernel configuration file.  If you have a non-PnP
+	ISA card, you will need to add:</para>
 
       <programlisting>device pcm
 device gus0 at isa? port 0x220 irq 5 drq 1 flags 0x13</programlisting>
@@ -195,9 +195,9 @@ device csa</programlisting>
 
       <programlisting>device pcm</programlisting>
 
-      <para>to your kernel configuration file.  If you have a non-PnP ISA
-	sound card that does not have a bridge driver, you will need
-	to add:</para>
+      <para>to your kernel configuration file.  If you have a non-PnP
+	ISA sound card that does not have a bridge driver, you will
+	need to add:</para>
 
       <programlisting>device pcm0 at isa? irq 10 drq 1 flags 0x0</programlisting>
 
@@ -221,20 +221,22 @@ device csa</programlisting>
     <title>Creating and Testing the Device Nodes</title>
 
     <indexterm><primary>device nodes</primary></indexterm>
-    <para>After you reboot, log in and run <command>dmesg | grep pcm</command> as shown
-      below:</para>
+    <para>After you reboot, log in and run <command>dmesg | grep
+      pcm</command> as shown below:</para>
 
     <screen>&prompt.root; dmesg | grep pcm
 pcm0: &lt;SB16 DSP 4.11&gt; on sbc0</screen>
 
     <para>The output from your system may look different.  If no
-      <devicename>pcm</devicename> devices show up, something went wrong
-      earlier.  If that happens, go through your kernel configuration
-      file again and make sure you chose the correct device.  Consult
-      the troubleshooting section for additional options.</para>
+      <devicename>pcm</devicename> devices show up, something went
+      wrong earlier.  If that happens, go through your kernel
+      configuration file again and make sure you chose the correct
+      device.  Consult the troubleshooting section for additional
+      options.</para>
 
-    <para>If the previous command returned <devicename>pcm0</devicename>,
-      you will have to run the following as root:</para>
+    <para>If the previous command returned
+      <devicename>pcm0</devicename>, you will have to run the
+      following as root:</para>
 
     <screen>&prompt.root; cd /dev
 &prompt.root; sh MAKEDEV snd0</screen>
@@ -327,7 +329,7 @@ pcm0: &lt;SB16 DSP 4.11&gt; on sbc0</screen>
 	    <row>
 	      <entry><errorname>unsupported subdevice XX</errorname></entry>
 	      <entry><para>One or more of the device nodes was not created
-	    correctly.  Repeat the steps above.</para></entry>
+	        correctly.  Repeat the steps above.</para></entry>
             </row>
 
             <indexterm><primary>I/O port</primary></indexterm>
@@ -388,15 +390,17 @@ pcm0: &lt;SB16 DSP 4.11&gt; on sbc0</screen>
       <para><application>XMMS</application> can be installed from the
 	<port>audio/xmms</port> port or package.</para>
 
-      <para><application>XMMS'</application> interface is intuitive, with
-	a playlist, graphic equalizer, and more.  Those familiar with WinAmp
-	will find <application>XMMS</application> simple to use.</para>
+      <para><application>XMMS'</application> interface is intuitive,
+	with a playlist, graphic equalizer, and more.  Those familiar
+	with <application>WinAmp</application> will find
+	<application>XMMS</application> simple to use.</para>
 
       <para>The <port>audio/mpg123</port> port is an alternative,
 	command-line MP3 player.</para>
 
-      <para><application>mpg123</application> can be run by specifying the
-	sound device and the MP3 file on the command line, as shown below:</para>
+      <para><application>mpg123</application> can be run by specifying
+	the sound device and the MP3 file on the command line, as
+	shown below:</para>
 
       <screen>&prompt.root; mpg123 -a <replaceable>/dev/dsp1.0</replaceable> Foobar-GreatestHits.mp3
 High Performance MPEG 1.0/2.0/2.5 Audio Player for Layer 1, 2 and 3.
@@ -425,28 +429,30 @@ MPEG 1.0 layer III, 128 kbit/s, 44100 Hz joint-stereo
 	copying the raw CDDA (CD Digital Audio) data to WAV
 	files.</para>
 
-      <para>The <command>cdda2wav</command> tool, which is a part of the
-	<port>sysutils/cdrtools</port> suite, is used for ripping audio
-	information of CDs and the information associated with it.</para>
+      <para>The <command>cdda2wav</command> tool, which is a part of
+	the <port>sysutils/cdrtools</port> suite, is used for ripping
+	audio information of CDs and the information associated with
+	it.</para>
 
-      <para>With the audio CD in the drive, the following command
-	can be issued (as <username>root</username>) to rip an entire
-	CD into individual (per track) WAV files:</para>
+      <para>With the audio CD in the drive, the following command can
+	be issued (as <username>root</username>) to rip an entire CD
+	into individual (per track) WAV files:</para>
 
       <screen>&prompt.root; cdda2wav -D <replaceable>0,1,0</replaceable> -B</screen>
 
       <para>The <option>-D <replaceable>0,1,0</replaceable></option>
-	indicates the SCSI device <devicename>0,1,0</devicename>, which
-	corresponds to the output of <command>cdrecord
-	  -scanbus</command>.</para>
+	indicates the SCSI device <devicename>0,1,0</devicename>,
+	which corresponds to the output of <command>cdrecord
+	-scanbus</command>.</para>
 
       <para>To rip individual tracks, make use of the
 	<option>-t</option> option as shown:</para>
 
       <screen>&prompt.root; cdda2wav -D <replaceable>0,1,0</replaceable> -t 7</screen>
 
-      <para>This example rips track seven of the audio CDROM.  To rip a range
-	of tracks, for example, track one to seven, specify a range:</para>
+      <para>This example rips track seven of the audio CDROM.  To rip
+	a range of tracks, for example, track one to seven, specify a
+	range:</para>
 
       <screen>&prompt.root; cdda2wav -D <replaceable>0,1,0</replaceable> -t 1+7</screen>
 
@@ -480,21 +486,23 @@ MPEG 1.0 layer III, 128 kbit/s, 44100 Hz joint-stereo
 
       <para>128 kbits seems to be the standard MP3 bitrate in use.
 	Many enjoy the higher quality 160, or 192.  The higher the
-	bitrate, the more disk space the resulting MP3 will consume--but
-	the quality will be higher.  The <option>-h</option> option
-	turns on the <quote>higher quality but a little slower</quote>
-	mode.  The options beginning with <option>--t</option> indicate
-	ID3 tags, which usually contain song information, to be embedded
-	within the MP3 file.  Additional encoding options can be found
-	by consulting the lame man page.</para>
+	bitrate, the more disk space the resulting MP3 will
+	consume--but the quality will be higher.  The
+	<option>-h</option> option turns on the <quote>higher quality
+	but a little slower</quote> mode.  The options beginning with
+	<option>--t</option> indicate ID3 tags, which usually contain
+	song information, to be embedded within the MP3 file.
+	Additional encoding options can be found by consulting the
+	lame man page.</para>
     </sect2>
 
     <sect2 id="mp3-decoding">
       <title>Decoding MP3s</title>
 
-      <para>In order to burn an audio CD from MP3s, they must be converted
-	to a non-compressed WAV format.  Both <application>XMMS</application>
-	and <application>mpg123</application> support the output of MP3 to
+      <para>In order to burn an audio CD from MP3s, they must be
+	converted to a non-compressed WAV format.  Both
+	<application>XMMS</application> and
+	<application>mpg123</application> support the output of MP3 to
 	an uncompressed file format.</para>
 
       <para>Writing to Disk in <application>XMMS</application>:</para>
@@ -535,14 +543,15 @@ MPEG 1.0 layer III, 128 kbit/s, 44100 Hz joint-stereo
 	</step>
 
 	<step>
-	  <para>Press <literal>Play</literal> &mdash; <application>XMMS</application>
-	    will appear as if it is playing the MP3, but no music will be heard.  It
-	    is actually playing the MP3 to a file.</para>
+	  <para>Press <literal>Play</literal> &mdash;
+	    <application>XMMS</application> will appear as if it is
+	    playing the MP3, but no music will be heard.  It is
+	    actually playing the MP3 to a file.</para>
 	</step>
 
 	<step>
-	  <para>Be sure to set the default Output Plugin back to what it was before
-	    in order to listen to MP3s again.</para>
+	  <para>Be sure to set the default Output Plugin back to what
+	    it was before in order to listen to MP3s again.</para>
 	</step>
       </procedure>
 
@@ -555,10 +564,12 @@ MPEG 1.0 layer III, 128 kbit/s, 44100 Hz joint-stereo
 	</step>
       </procedure>
 
-      <para><application>XMMS</application> writes a file in the WAV format, while
-	<application>mpg123</application> converts the MP3 into raw PCM audio data.
-	Both of these formats can be used with <application>cdrecord</application>
-	or <application>burncd</application> to create audio CDROMs.</para>
+      <para><application>XMMS</application> writes a file in the WAV
+	format, while <application>mpg123</application> converts the
+	MP3 into raw PCM audio data.  Both of these formats can be
+	used with <application>cdrecord</application> or
+	<application>burncd</application> to create audio
+	CDROMs.</para>
 
       <para>Read <xref linkend="creating-cds"> for more information on using a
 	  CD burner in FreeBSD.</para>