aboutsummaryrefslogtreecommitdiff
path: root/en_US.ISO8859-1/books/handbook/serialcomms/chapter.sgml
diff options
context:
space:
mode:
Diffstat (limited to 'en_US.ISO8859-1/books/handbook/serialcomms/chapter.sgml')
-rw-r--r--en_US.ISO8859-1/books/handbook/serialcomms/chapter.sgml18
1 files changed, 9 insertions, 9 deletions
diff --git a/en_US.ISO8859-1/books/handbook/serialcomms/chapter.sgml b/en_US.ISO8859-1/books/handbook/serialcomms/chapter.sgml
index 7bfa0e699a..6451a4b97d 100644
--- a/en_US.ISO8859-1/books/handbook/serialcomms/chapter.sgml
+++ b/en_US.ISO8859-1/books/handbook/serialcomms/chapter.sgml
@@ -810,7 +810,7 @@ sio3: type 16550A</screen>
through the Ports Collection. The Ports include quite a few
utilities which can work in ways similar to &man.cu.1; and
&man.tip.1;,
- i.e., <filename role="package">comms/minicom</filename>.</para>
+ i.e. <filename role="package">comms/minicom</filename>.</para>
</note>
</sect3>
@@ -1173,7 +1173,7 @@ ttyu5 "/usr/libexec/getty std.19200" vt100 on insecure
modems instead of terminals.</para>
<sect2>
- <title>External Versus Internal Modems</title>
+ <title>External vs. Internal Modems</title>
<para>External modems seem to be more convenient for dial-up, because
external modems often can be semi-permanently configured via
@@ -1881,7 +1881,7 @@ AT&amp;B2&amp;W</programlisting>
</sect2>
<sect2 id="direct-at">
- <title>How Am I Expected to Enter These <literal>AT</literal> Commands?</title>
+ <title>How Am I Expected to Enter These AT Commands?</title>
<indexterm>
<primary><filename>/etc/remote</filename></primary>
@@ -1895,7 +1895,7 @@ AT&amp;B2&amp;W</programlisting>
<para>Use the highest bps rate your modem supports in the br capability.
Then, type <command>tip cuau0</command> and you will be connected to
- your modem.</para >
+ your modem.</para>
<para>Or use <command>cu</command> as <username>root</username> with the
following command:</para>
@@ -1903,9 +1903,9 @@ AT&amp;B2&amp;W</programlisting>
<screen>&prompt.root; <userinput>cu -l<replaceable>line</replaceable> -s<replaceable>speed</replaceable></userinput></screen>
<para><replaceable>line</replaceable> is the serial port
- (e.g., <filename>/dev/cuau0</filename>) and
+ (e.g.<filename>/dev/cuau0</filename>) and
<replaceable>speed</replaceable> is the speed
- (e.g., <literal>57600</literal>). When you are done entering the AT
+ (e.g.<literal>57600</literal>). When you are done entering the AT
commands type <command>~.</command> to exit.</para>
</sect2>
@@ -2117,7 +2117,7 @@ raisechar=^^</programlisting>
</sect2>
<sect2 id="zmodem-tip">
- <title>How Can I Run <application>zmodem</application> with <command>tip</command>?</title>
+ <title>How Can I Run zmodem with <command>tip</command>?</title>
<para>To receive files, start the sending program on the remote end.
Then, type <command>~C rz</command> to begin receiving them
@@ -2829,7 +2829,7 @@ ttyu3 "/usr/libexec/getty std.9600" unknown off secure</programlisting>
Change <literal>off</literal> to <literal>on</literal> for the
desired port. If you have changed the speed of the serial port,
you need to change <literal>std.9600</literal> to match the current
- setting, e.g., <literal>std.19200</literal>.</para>
+ setting, e.g. <literal>std.19200</literal>.</para>
<para>You may also want to change the terminal type from
<literal>unknown</literal> to the actual type of your serial
@@ -2907,7 +2907,7 @@ ttyu3 "/usr/libexec/getty std.9600" unknown off secure</programlisting>
while most systems will let you boot without a keyboard, there
are quite a few that will not let you boot without a graphics adapter.
Machines with AMI BIOSes can be configured to boot with no graphics
- adapter installed by changing the
+ adapter installed simply by changing the
<quote>graphics adapter</quote> setting in the CMOS configuration to
<quote>Not installed.</quote></para>