Contributed by &a.gena;. Before you start setting up PPP on your machine make sure that pppd is located in /usr/sbin and directory /etc/ppp exists. pppd can work in two modes: as a "client" , i.e. you want to connect your machine to outside world via PPP serial connection or modem line. as a "server" , i.e. your machine is located on the network and used to connect other computers using PPP. In both cases you will need to set up an options file ( /etc/ppp/options or ~/.ppprc if you have more then one user on your machine that uses PPP ). You also will need some modem/serial software ( preferably kermit ) so you can dial and establish connection with remote host. Working as a PPP client

I used the following /etc/ppp/options to connect to CISCO terminal server PPP line. crtscts # enable hardware flow control modem # modem control line noipdefault # remote PPP server must supply your IP address. # if the remote host doesn't send your IP during IPCP # negotiation , remove this option passive # wait for LCP packets domain ppp.foo.com # put your domain name here : # put the IP of remote PPP host here # it will be used to route packets via PPP link # if you didn't specified the noipdefault option # change this line to : defaultroute # put this if you want that PPP server will be your # default router To connect: Dial to the remote host using kermit ( or other modem program ) enter your user name and password ( or whatever is needed to enable PPP ont the remote host ) Exit kermit. ( without hanging up the line ) enter: /usr/src/usr.sbin/pppd.new/pppd /dev/tty01 19200 ( put the appropriate speed and device name ) Now your computer is connected with PPP. If the connection fails for some reasons you can add the "debug" option to the /etc/ppp/options file and check messages on the console to track the problem Following /etc/ppp/pppup script will make all 3 stages automatically: #!/bin/sh ps ax |grep pppd |grep -v grep pid=`ps ax |grep pppd |grep -v grep|awk '{print $1;}'` if [ "X${pid}" != "X" ] ; then echo 'killing pppd, PID=' ${pid} kill ${pid} fi ps ax |grep kermit |grep -v grep pid=`ps ax |grep kermit |grep -v grep|awk '{print $1;}'` if [ "X${pid}" != "X" ] ; then echo 'killing kermit, PID=' ${pid} kill -9 ${pid} fi ifconfig ppp0 down ifconfig ppp0 delete kermit -y /etc/ppp/kermit.dial pppd /dev/tty01 19200 /etc/ppp/kermit.dial is kermit script that dials and makes all necessary authorization on the remote host. ( Example of such script is attached to the end of this document ) Use the follwing /etc/ppp/pppdown script to disconnect the PPP line: #!/bin/sh pid=`ps ax |grep pppd |grep -v grep|awk '{print $1;}'` if [ X${pid} != "X" ] ; then echo 'killing pppd, PID=' ${pid} kill -TERM ${pid} fi ps ax |grep kermit |grep -v grep pid=`ps ax |grep kermit |grep -v grep|awk '{print $1;}'` if [ "X${pid}" != "X" ] ; then echo 'killing kermit, PID=' ${pid} kill -9 ${pid} fi /sbin/ifconfig ppp0 down /sbin/ifconfig ppp0 delete kermit -y /etc/ppp/kermit.hup /etc/ppp/ppptest Check if PPP is still running (/usr/etc/ppp/ppptest): #!/bin/sh pid=`ps ax| grep pppd |grep -v grep|awk '{print $1;}'` if [ X${pid} != "X" ] ; then echo 'pppd running: PID=' ${pid-NONE} else echo 'No pppd running.' fi set -x netstat -n -I ppp0 ifconfig ppp0 Hangs up modem line (/etc/ppp/kermit.hup): set line /dev/tty01 ; put your modem device here set speed 19200 set file type binary set file names literal set win 8 set rec pack 1024 set send pack 1024 set block 3 set term bytesize 8 set command bytesize 8 set flow none pau 1 out +++ inp 5 OK out ATH0\13 echo \13 exit Working as a PPP server

/etc/ppp/options: crtscts # Hardware flow control netmask 255.255.255.0 # netmask ( not required ) 192.114.208.20:192.114.208.165 # ip's of local and remote hosts # local ip must be different from one # you assigned to the ethernet ( or other ) # interface on your machine. # remote IP is ip address that will be # assigned to the remote machine domain ppp.foo.com # your domain passive # wait for LCP modem # modem line Following /etc/ppp/pppserv script will enable ppp server on your machine #!/bin/sh ps ax |grep pppd |grep -v grep pid=`ps ax |grep pppd |grep -v grep|awk '{print $1;}'` if [ "X${pid}" != "X" ] ; then echo 'killing pppd, PID=' ${pid} kill ${pid} fi ps ax |grep kermit |grep -v grep pid=`ps ax |grep kermit |grep -v grep|awk '{print $1;}'` if [ "X${pid}" != "X" ] ; then echo 'killing kermit, PID=' ${pid} kill -9 ${pid} fi # reset ppp interface ifconfig ppp0 down ifconfig ppp0 delete # enable autoanswer mode kermit -y /etc/ppp/kermit.ans # run ppp pppd /dev/tty01 19200 Use this /etc/ppp/pppservdown script to stop ppp server: #!/bin/sh ps ax |grep pppd |grep -v grep pid=`ps ax |grep pppd |grep -v grep|awk '{print $1;}'` if [ "X${pid}" != "X" ] ; then echo 'killing pppd, PID=' ${pid} kill ${pid} fi ps ax |grep kermit |grep -v grep pid=`ps ax |grep kermit |grep -v grep|awk '{print $1;}'` if [ "X${pid}" != "X" ] ; then echo 'killing kermit, PID=' ${pid} kill -9 ${pid} fi ifconfig ppp0 down ifconfig ppp0 delete kermit -y /etc/ppp/kermit.noans Following kermit script will enable/disable autoanswer mode on your modem (/etc/ppp/kermit.ans): set line /dev/tty01 set speed 19200 set file type binary set file names literal set win 8 set rec pack 1024 set send pack 1024 set block 3 set term bytesize 8 set command bytesize 8 set flow none pau 1 out +++ inp 5 OK out ATH0\13 inp 5 OK echo \13 out ATS0=1\13 ; change this to out ATS0=0\13 if you want to disable ; autoanswer mod inp 5 OK echo \13 exit This /etc/ppp/kermit.dial script is used for dialing and authorizing on remote host. You will need to customize it for your needs. Put your login and password in this script , also you'll need to change input statement depending on responces from your modem and remote host. ; ; put the com line attached to the modem here: ; set line /dev/tty01 ; ; put the modem speed here: ; set speed 19200 set file type binary ; full 8 bit file xfer set file names literal set win 8 set rec pack 1024 set send pack 1024 set block 3 set term bytesize 8 set command bytesize 8 set flow none set modem hayes set dial hangup off set carrier auto ; Then SET CARRIER if necessary, set dial display on ; Then SET DIAL if necessary, set input echo on set input timeout proceed set input case ignore def \%x 0 ; login prompt counter goto slhup :slcmd ; put the modem in command mode echo Put the modem in command mode. clear ; Clear unread characters from input buffer pause 1 output +++ ; hayes escape sequence input 1 OK\13\10 ; wait for OK if success goto slhup output \13 pause 1 output at\13 input 1 OK\13\10 if fail goto slcmd ; if modem doesn't answer OK, try again :slhup ; hang up the phone clear ; Clear unread characters from input buffer pause 1 echo Hanging up the phone. output ath0\13 ; hayes command for on hook input 2 OK\13\10 if fail goto slcmd ; if no OK answer, put modem in command mode :sldial ; dial the number pause 1 echo Dialing. output atdt9,550311\13\10 ; put phone number here assign \%x 0 ; zero the time counter :look clear ; Clear unread characters from input buffer increment \%x ; Count the seconds input 1 {CONNECT } if success goto sllogin reinput 1 {NO CARRIER\13\10} if success goto sldial reinput 1 {NO DIALTONE\13\10} if success goto slnodial reinput 1 {\255} if success goto slhup reinput 1 {\127} if success goto slhup if < \%x 60 goto look else goto slhup :sllogin ; login assign \%x 0 ; zero the time counter pause 1 echo Looking for login prompt. :slloop increment \%x ; Count the seconds clear ; Clear unread characters from input buffer output \13 ; ; put your expected login prompt here: ; input 1 {Username: } if success goto sluid reinput 1 {\255} if success goto slhup reinput 1 {\127} if success goto slhup if < \%x 10 goto slloop ; try 10 times to get a login prompt else goto slhup ; hang up and start again if 10 failures :sluid ; ; put your userid here: ; output ppp-login\13 input 1 {Password: } ; ; put your password here: ; output ppp-password\13 input 1 {Entering SLIP mode.} echo quit :slnodial echo \7No dialtone. Check the telephone line!\7 exit 1 ; local variables: ; mode: csh ; comment-start: "; " ; comment-start-skip: "; " ; end: