Import DTS files from Linux 5.6vendor/device-tree/5.6

14 files changed, 492 insertions, 26 deletions

diff --git a/Bindings/net/brcm,bcm7445-switch-v4.0.txt b/Bindings/net/brcm,bcm7445-switch-v4.0.txt
index 48a7f916c5e4..88b57b0ca1f4 100644
--- a/Bindings/net/brcm,bcm7445-switch-v4.0.txt
+++ b/Bindings/net/brcm,bcm7445-switch-v4.0.txt
@@ -45,7 +45,7 @@ Optional properties:
   switch queue
 
 - resets: a single phandle and reset identifier pair. See
-  Documentation/devicetree/binding/reset/reset.txt for details.
+  Documentation/devicetree/bindings/reset/reset.txt for details.
 
 - reset-names: If the "reset" property is specified, this property should have
   the value "switch" to denote the switch reset line.
diff --git a/Bindings/net/broadcom-bluetooth.txt b/Bindings/net/broadcom-bluetooth.txt
index f16b99571af1..dd258674633c 100644
--- a/Bindings/net/broadcom-bluetooth.txt
+++ b/Bindings/net/broadcom-bluetooth.txt
@@ -11,6 +11,7 @@ Required properties:
 
  - compatible: should contain one of the following:
    * "brcm,bcm20702a1"
+   * "brcm,bcm4329-bt"
    * "brcm,bcm4330-bt"
    * "brcm,bcm43438-bt"
    * "brcm,bcm4345c5"
@@ -22,7 +23,9 @@ Optional properties:
  - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt
  - shutdown-gpios: GPIO specifier, used to enable the BT module
  - device-wakeup-gpios: GPIO specifier, used to wakeup the controller
- - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor
+ - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor.
+                      deprecated, replaced by interrupts and
+                      "host-wakeup" interrupt-names
  - clocks: 1 or 2 clocks as defined in clock-names below, in that order
  - clock-names: names for clock inputs, matching the clocks given
    - "extclk": deprecated, replaced by "txco"
@@ -30,7 +33,14 @@ Optional properties:
    - "lpo": external low power 32.768 kHz clock
  - vbat-supply: phandle to regulator supply for VBAT
  - vddio-supply: phandle to regulator supply for VDDIO
-
+ - brcm,bt-pcm-int-params: configure PCM parameters via a 5-byte array
+    - sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S
+    - pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
+    - pcm-frame-type: short, long
+    - pcm-sync-mode: slave, master
+    - pcm-clock-mode: slave, master
+ - interrupts: must be one, used to wakeup the host processor
+ - interrupt-names: must be "host-wakeup"
 
 Example:
 
@@ -41,5 +51,6 @@ Example:
        bluetooth {
                compatible = "brcm,bcm43438-bt";
                max-speed = <921600>;
+               brcm,bt-pcm-int-params = [01 02 00 01 01];
        };
 };
diff --git a/Bindings/net/can/atmel-can.txt b/Bindings/net/can/atmel-can.txt
index 14e52a0d86ec..218a3b3eb27e 100644
--- a/Bindings/net/can/atmel-can.txt
+++ b/Bindings/net/can/atmel-can.txt
@@ -1,7 +1,8 @@
 * AT91 CAN *
 
 Required properties:
-  - compatible: Should be "atmel,at91sam9263-can" or "atmel,at91sam9x5-can"
+  - compatible: Should be "atmel,at91sam9263-can", "atmel,at91sam9x5-can" or
+    "microchip,sam9x60-can"
   - reg: Should contain CAN controller registers location and length
   - interrupts: Should contain IRQ line for the CAN controller
 
diff --git a/Bindings/net/can/rcar_can.txt b/Bindings/net/can/rcar_can.txt
index 19e4a7d91511..85c6551b602a 100644
--- a/Bindings/net/can/rcar_can.txt
+++ b/Bindings/net/can/rcar_can.txt
@@ -7,6 +7,7 @@ Required properties:
 	      "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC.
 	      "renesas,can-r8a77470" if CAN controller is a part of R8A77470 SoC.
 	      "renesas,can-r8a774a1" if CAN controller is a part of R8A774A1 SoC.
+	      "renesas,can-r8a774b1" if CAN controller is a part of R8A774B1 SoC.
 	      "renesas,can-r8a774c0" if CAN controller is a part of R8A774C0 SoC.
 	      "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC.
 	      "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC.
@@ -36,8 +37,8 @@ Required properties:
 - pinctrl-0: pin control group to be used for this controller.
 - pinctrl-names: must be "default".
 
-Required properties for R8A774A1, R8A774C0, R8A7795, R8A7796, R8A77965,
-R8A77990, and R8A77995:
+Required properties for R8A774A1, R8A774B1, R8A774C0, R8A7795, R8A7796,
+R8A77965, R8A77990, and R8A77995:
 For the denoted SoCs, "clkp2" can be CANFD clock. This is a div6 clock and can
 be used by both CAN and CAN FD controller at the same time. It needs to be
 scaled to maximum frequency if any of these controllers use it. This is done
diff --git a/Bindings/net/can/rcar_canfd.txt b/Bindings/net/can/rcar_canfd.txt
index a901cd9be29e..13a4e34c0c73 100644
--- a/Bindings/net/can/rcar_canfd.txt
+++ b/Bindings/net/can/rcar_canfd.txt
@@ -5,6 +5,7 @@ Required properties:
 - compatible: Must contain one or more of the following:
   - "renesas,rcar-gen3-canfd" for R-Car Gen3 and RZ/G2 compatible controllers.
   - "renesas,r8a774a1-canfd" for R8A774A1 (RZ/G2M) compatible controller.
+  - "renesas,r8a774b1-canfd" for R8A774B1 (RZ/G2N) compatible controller.
   - "renesas,r8a774c0-canfd" for R8A774C0 (RZ/G2E) compatible controller.
   - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller.
   - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller.
@@ -31,8 +32,8 @@ The name of the child nodes are "channel0" and "channel1" respectively. Each
 child node supports the "status" property only, which is used to
 enable/disable the respective channel.
 
-Required properties for R8A774A1, R8A774C0, R8A7795, R8A7796, R8A77965,
-R8A77990, and R8A77995:
+Required properties for R8A774A1, R8A774B1, R8A774C0, R8A7795, R8A7796,
+R8A77965, R8A77990, and R8A77995:
 In the denoted SoCs, canfd clock is a div6 clock and can be used by both CAN
 and CAN FD controller at the same time. It needs to be scaled to maximum
 frequency if any of these controllers use it. This is done using the below
diff --git a/Bindings/net/dsa/ar9331.txt b/Bindings/net/dsa/ar9331.txt
new file mode 100644
index 000000000000..320607cbbb17
--- /dev/null
+++ b/Bindings/net/dsa/ar9331.txt
@@ -0,0 +1,148 @@
+Atheros AR9331 built-in switch
+=============================
+
+It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal
+MDIO bus. All PHYs are built-in as well.
+
+Required properties:
+
+ - compatible: should be: "qca,ar9331-switch"
+ - reg: Address on the MII bus for the switch.
+ - resets : Must contain an entry for each entry in reset-names.
+ - reset-names : Must include the following entries: "switch"
+ - interrupt-parent: Phandle to the parent interrupt controller
+ - interrupts: IRQ line for the switch
+ - interrupt-controller: Indicates the switch is itself an interrupt
+   controller. This is used for the PHY interrupts.
+ - #interrupt-cells: must be 1
+ - mdio: Container of PHY and devices on the switches MDIO bus.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+Examples:
+
+eth0: ethernet@19000000 {
+	compatible = "qca,ar9330-eth";
+	reg = <0x19000000 0x200>;
+	interrupts = <4>;
+
+	resets = <&rst 9>, <&rst 22>;
+	reset-names = "mac", "mdio";
+	clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+	clock-names = "eth", "mdio";
+
+	phy-mode = "mii";
+	phy-handle = <&phy_port4>;
+};
+
+eth1: ethernet@1a000000 {
+	compatible = "qca,ar9330-eth";
+	reg = <0x1a000000 0x200>;
+	interrupts = <5>;
+	resets = <&rst 13>, <&rst 23>;
+	reset-names = "mac", "mdio";
+	clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+	clock-names = "eth", "mdio";
+
+	phy-mode = "gmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch10: switch@10 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			compatible = "qca,ar9331-switch";
+			reg = <0x10>;
+			resets = <&rst 8>;
+			reset-names = "switch";
+
+			interrupt-parent = <&miscintc>;
+			interrupts = <12>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch_port0: port@0 {
+					reg = <0x0>;
+					label = "cpu";
+					ethernet = <&eth1>;
+
+					phy-mode = "gmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				switch_port1: port@1 {
+					reg = <0x1>;
+					phy-handle = <&phy_port0>;
+					phy-mode = "internal";
+				};
+
+				switch_port2: port@2 {
+					reg = <0x2>;
+					phy-handle = <&phy_port1>;
+					phy-mode = "internal";
+				};
+
+				switch_port3: port@3 {
+					reg = <0x3>;
+					phy-handle = <&phy_port2>;
+					phy-mode = "internal";
+				};
+
+				switch_port4: port@4 {
+					reg = <0x4>;
+					phy-handle = <&phy_port3>;
+					phy-mode = "internal";
+				};
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				interrupt-parent = <&switch10>;
+
+				phy_port0: phy@0 {
+					reg = <0x0>;
+					interrupts = <0>;
+				};
+
+				phy_port1: phy@1 {
+					reg = <0x1>;
+					interrupts = <0>;
+				};
+
+				phy_port2: phy@2 {
+					reg = <0x2>;
+					interrupts = <0>;
+				};
+
+				phy_port3: phy@3 {
+					reg = <0x3>;
+					interrupts = <0>;
+				};
+
+				phy_port4: phy@4 {
+					reg = <0x4>;
+					interrupts = <0>;
+				};
+			};
+		};
+	};
+};
diff --git a/Bindings/net/fsl-fman.txt b/Bindings/net/fsl-fman.txt
index 250f8d8cdce4..c00fb0d22c7b 100644
--- a/Bindings/net/fsl-fman.txt
+++ b/Bindings/net/fsl-fman.txt
@@ -110,6 +110,13 @@ PROPERTIES
 		Usage: required
 		Definition: See soc/fsl/qman.txt and soc/fsl/bman.txt
 
+- fsl,erratum-a050385
+		Usage: optional
+		Value type: boolean
+		Definition: A boolean property. Indicates the presence of the
+		erratum A050385 which indicates that DMA transactions that are
+		split can result in a FMan lock.
+
 =============================================================================
 FMan MURAM Node
 
diff --git a/Bindings/net/mdio.yaml b/Bindings/net/mdio.yaml
index 5d08d2ffd4eb..50c3397a82bc 100644
--- a/Bindings/net/mdio.yaml
+++ b/Bindings/net/mdio.yaml
@@ -56,7 +56,6 @@ patternProperties:
 examples:
   - |
     davinci_mdio: mdio@5c030000 {
-        compatible = "ti,davinci_mdio";
         reg = <0x5c030000 0x1000>;
         #address-cells = <1>;
         #size-cells = <0>;
diff --git a/Bindings/net/mediatek-dwmac.txt b/Bindings/net/mediatek-dwmac.txt
index 8a08621a5b54..afbcaebf062e 100644
--- a/Bindings/net/mediatek-dwmac.txt
+++ b/Bindings/net/mediatek-dwmac.txt
@@ -14,7 +14,7 @@ Required properties:
 	Should be "macirq" for the main MAC IRQ
 - clocks: Must contain a phandle for each entry in clock-names.
 - clock-names: The name of the clock listed in the clocks property. These are
-	"axi", "apb", "mac_main", "ptp_ref" for MT2712 SoC
+	"axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC.
 - mac-address: See ethernet.txt in the same directory
 - phy-mode: See ethernet.txt in the same directory
 - mediatek,pericfg: A phandle to the syscon node that control ethernet
@@ -23,8 +23,10 @@ Required properties:
 Optional properties:
 - mediatek,tx-delay-ps: TX clock delay macro value. Default is 0.
 	It should be defined for RGMII/MII interface.
+	It should be defined for RMII interface when the reference clock is from MT2712 SoC.
 - mediatek,rx-delay-ps: RX clock delay macro value. Default is 0.
-	It should be defined for RGMII/MII/RMII interface.
+	It should be defined for RGMII/MII interface.
+	It should be defined for RMII interface.
 Both delay properties need to be a multiple of 170 for RGMII interface,
 or will round down. Range 0~31*170.
 Both delay properties need to be a multiple of 550 for MII/RMII interface,
@@ -34,13 +36,20 @@ or will round down. Range 0~31*550.
 	reference clock, which is from external PHYs, is connected to RXC pin
 	on MT2712 SoC.
 	Otherwise, is connected to TXC pin.
+- mediatek,rmii-clk-from-mac: boolean property, if present indicates that
+	MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only.
 - mediatek,txc-inverse: boolean property, if present indicates that
 	1. tx clock will be inversed in MII/RGMII case,
 	2. tx clock inside MAC will be inversed relative to reference clock
 	   which is from external PHYs in RMII case, and it rarely happen.
+	3. the reference clock, which outputs to TXC pin will be inversed in RMII case
+	   when the reference clock is from MT2712 SoC.
 - mediatek,rxc-inverse: boolean property, if present indicates that
 	1. rx clock will be inversed in MII/RGMII case.
-	2. reference clock will be inversed when arrived at MAC in RMII case.
+	2. reference clock will be inversed when arrived at MAC in RMII case, when
+	   the reference clock is from external PHYs.
+	3. the inside clock, which be sent to MAC, will be inversed in RMII case when
+	   the reference clock is from MT2712 SoC.
 - assigned-clocks: mac_main and ptp_ref clocks
 - assigned-clock-parents: parent clocks of the assigned clocks
 
@@ -50,29 +59,33 @@ Example:
 		reg = <0 0x1101c000 0 0x1300>;
 		interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "macirq";
-		phy-mode ="rgmii";
+		phy-mode ="rgmii-rxid";
 		mac-address = [00 55 7b b5 7d f7];
 		clock-names = "axi",
 			      "apb",
 			      "mac_main",
 			      "ptp_ref",
-			      "ptp_top";
+			      "rmii_internal";
 		clocks = <&pericfg CLK_PERI_GMAC>,
 			 <&pericfg CLK_PERI_GMAC_PCLK>,
 			 <&topckgen CLK_TOP_ETHER_125M_SEL>,
-			 <&topckgen CLK_TOP_ETHER_50M_SEL>;
+			 <&topckgen CLK_TOP_ETHER_50M_SEL>,
+			 <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
 		assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
-				  <&topckgen CLK_TOP_ETHER_50M_SEL>;
+				  <&topckgen CLK_TOP_ETHER_50M_SEL>,
+				  <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
 		assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
-					 <&topckgen CLK_TOP_APLL1_D3>;
+					 <&topckgen CLK_TOP_APLL1_D3>,
+					 <&topckgen CLK_TOP_ETHERPLL_50M>;
+		power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
 		mediatek,pericfg = <&pericfg>;
 		mediatek,tx-delay-ps = <1530>;
 		mediatek,rx-delay-ps = <1530>;
 		mediatek,rmii-rxc;
 		mediatek,txc-inverse;
 		mediatek,rxc-inverse;
-		snps,txpbl = <32>;
-		snps,rxpbl = <32>;
+		snps,txpbl = <1>;
+		snps,rxpbl = <1>;
 		snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
 		snps,reset-active-low;
 	};
diff --git a/Bindings/net/qualcomm-bluetooth.txt b/Bindings/net/qualcomm-bluetooth.txt
index 68b67d9db63a..999aceadb985 100644
--- a/Bindings/net/qualcomm-bluetooth.txt
+++ b/Bindings/net/qualcomm-bluetooth.txt
@@ -11,6 +11,7 @@ Required properties:
  - compatible: should contain one of the following:
    * "qcom,qca6174-bt"
    * "qcom,wcn3990-bt"
+   * "qcom,wcn3991-bt"
    * "qcom,wcn3998-bt"
 
 Optional properties for compatible string qcom,qca6174-bt:
diff --git a/Bindings/net/renesas,ravb.txt b/Bindings/net/renesas,ravb.txt
index 5df4aa7f6811..87dad2dd8ca0 100644
--- a/Bindings/net/renesas,ravb.txt
+++ b/Bindings/net/renesas,ravb.txt
@@ -21,7 +21,8 @@ Required properties:
       - "renesas,etheravb-r8a774b1" for the R8A774B1 SoC.
       - "renesas,etheravb-r8a774c0" for the R8A774C0 SoC.
       - "renesas,etheravb-r8a7795" for the R8A7795 SoC.
-      - "renesas,etheravb-r8a7796" for the R8A7796 SoC.
+      - "renesas,etheravb-r8a7796" for the R8A77960 SoC.
+      - "renesas,etheravb-r8a77961" for the R8A77961 SoC.
       - "renesas,etheravb-r8a77965" for the R8A77965 SoC.
       - "renesas,etheravb-r8a77970" for the R8A77970 SoC.
       - "renesas,etheravb-r8a77980" for the R8A77980 SoC.
@@ -37,8 +38,8 @@ Required properties:
 - reg: Offset and length of (1) the register block and (2) the stream buffer.
        The region for the register block is mandatory.
        The region for the stream buffer is optional, as it is only present on
-       R-Car Gen2 and RZ/G1 SoCs, and on R-Car H3 (R8A7795), M3-W (R8A7796),
-       and M3-N (R8A77965).
+       R-Car Gen2 and RZ/G1 SoCs, and on R-Car H3 (R8A7795), M3-W (R8A77960),
+       M3-W+ (R8A77961), and M3-N (R8A77965).
 - interrupts: A list of interrupt-specifiers, one for each entry in
 	      interrupt-names.
 	      If interrupt-names is not present, an interrupt specifier
diff --git a/Bindings/net/ti,dp83867.txt b/Bindings/net/ti,dp83867.txt
index 388ff48f53ae..44e2a4fab29e 100644
--- a/Bindings/net/ti,dp83867.txt
+++ b/Bindings/net/ti,dp83867.txt
@@ -8,8 +8,6 @@ Required properties:
 	- ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h
 		for applicable values. Required only if interface type is
 		PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID
-	- ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h
-		for applicable values
 
 Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays
       will be left at their default values, as set by the PHY's pin strapping.
@@ -42,6 +40,14 @@ Optional property:
 				    Some MACs work with differential SGMII clock.
 				    See data manual for details.
 
+	- ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h
+		for applicable values (deprecated)
+
+	-tx-fifo-depth - As defined in the ethernet-controller.yaml.  Values for
+			 the depth can be found in dt-bindings/net/ti-dp83867.h
+	-rx-fifo-depth - As defined in the ethernet-controller.yaml.  Values for
+			 the depth can be found in dt-bindings/net/ti-dp83867.h
+
 Note: ti,min-output-impedance and ti,max-output-impedance are mutually
       exclusive. When both properties are present ti,max-output-impedance
       takes precedence.
@@ -55,7 +61,7 @@ Example:
 		reg = <0>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
 		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
-		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 	};
 
 Datasheet can be found:
diff --git a/Bindings/net/wireless/qcom,ath10k.txt b/Bindings/net/wireless/qcom,ath10k.txt
index 017128394a3e..616c87746d6f 100644
--- a/Bindings/net/wireless/qcom,ath10k.txt
+++ b/Bindings/net/wireless/qcom,ath10k.txt
@@ -50,7 +50,7 @@ Optional properties:
           entry in clock-names.
 - clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref",
 	       "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and
-	       "cxo_ref_clk_pin" for "qcom,wcn3990-wifi"
+	       "cxo_ref_clk_pin" and optionally "qdss" for "qcom,wcn3990-wifi"
 	       compatible target.
 - qcom,msi_addr: MSI interrupt address.
 - qcom,msi_base: Base value to add before writing MSI data into
@@ -88,6 +88,9 @@ Optional properties:
 		    of the host capability QMI request
 - qcom,xo-cal-data: xo cal offset to be configured in xo trim register.
 
+- qcom,msa-fixed-perm: Boolean context flag to disable SCM call for statically
+		       mapped msa region.
+
 Example (to supply PCI based wifi block details):
 
 In this example, the node is defined as child node of the PCI controller.
@@ -185,4 +188,5 @@ wifi@18000000 {
 		vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 		memory-region = <&wifi_msa_mem>;
 		iommus = <&apps_smmu 0x0040 0x1>;
+		qcom,msa-fixed-perm;
 };
diff --git a/Bindings/net/wireless/qcom,ath11k.yaml b/Bindings/net/wireless/qcom,ath11k.yaml
new file mode 100644
index 000000000000..a1717db36dba
--- /dev/null
+++ b/Bindings/net/wireless/qcom,ath11k.yaml
@@ -0,0 +1,273 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/qcom,ath11k.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies ath11k wireless devices Generic Binding
+
+maintainers:
+  - Kalle Valo <kvalo@codeaurora.org>
+
+description: |
+  These are dt entries for Qualcomm Technologies, Inc. IEEE 802.11ax
+  devices, for example like AHB based IPQ8074.
+
+properties:
+  compatible:
+    const: qcom,ipq8074-wifi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: misc-pulse1 interrupt events
+      - description: misc-latch interrupt events
+      - description: sw exception interrupt events
+      - description: watchdog interrupt events
+      - description: interrupt event for ring CE0
+      - description: interrupt event for ring CE1
+      - description: interrupt event for ring CE2
+      - description: interrupt event for ring CE3
+      - description: interrupt event for ring CE4
+      - description: interrupt event for ring CE5
+      - description: interrupt event for ring CE6
+      - description: interrupt event for ring CE7
+      - description: interrupt event for ring CE8
+      - description: interrupt event for ring CE9
+      - description: interrupt event for ring CE10
+      - description: interrupt event for ring CE11
+      - description: interrupt event for ring host2wbm-desc-feed
+      - description: interrupt event for ring host2reo-re-injection
+      - description: interrupt event for ring host2reo-command
+      - description: interrupt event for ring host2rxdma-monitor-ring3
+      - description: interrupt event for ring host2rxdma-monitor-ring2
+      - description: interrupt event for ring host2rxdma-monitor-ring1
+      - description: interrupt event for ring reo2ost-exception
+      - description: interrupt event for ring wbm2host-rx-release
+      - description: interrupt event for ring reo2host-status
+      - description: interrupt event for ring reo2host-destination-ring4
+      - description: interrupt event for ring reo2host-destination-ring3
+      - description: interrupt event for ring reo2host-destination-ring2
+      - description: interrupt event for ring reo2host-destination-ring1
+      - description: interrupt event for ring rxdma2host-monitor-destination-mac3
+      - description: interrupt event for ring rxdma2host-monitor-destination-mac2
+      - description: interrupt event for ring rxdma2host-monitor-destination-mac1
+      - description: interrupt event for ring ppdu-end-interrupts-mac3
+      - description: interrupt event for ring ppdu-end-interrupts-mac2
+      - description: interrupt event for ring ppdu-end-interrupts-mac1
+      - description: interrupt event for ring rxdma2host-monitor-status-ring-mac3
+      - description: interrupt event for ring rxdma2host-monitor-status-ring-mac2
+      - description: interrupt event for ring rxdma2host-monitor-status-ring-mac1
+      - description: interrupt event for ring host2rxdma-host-buf-ring-mac3
+      - description: interrupt event for ring host2rxdma-host-buf-ring-mac2
+      - description: interrupt event for ring host2rxdma-host-buf-ring-mac1
+      - description: interrupt event for ring rxdma2host-destination-ring-mac3
+      - description: interrupt event for ring rxdma2host-destination-ring-mac2
+      - description: interrupt event for ring rxdma2host-destination-ring-mac1
+      - description: interrupt event for ring host2tcl-input-ring4
+      - description: interrupt event for ring host2tcl-input-ring3
+      - description: interrupt event for ring host2tcl-input-ring2
+      - description: interrupt event for ring host2tcl-input-ring1
+      - description: interrupt event for ring wbm2host-tx-completions-ring3
+      - description: interrupt event for ring wbm2host-tx-completions-ring2
+      - description: interrupt event for ring wbm2host-tx-completions-ring1
+      - description: interrupt event for ring tcl2host-status-ring
+
+
+  interrupt-names:
+    items:
+      - const: misc-pulse1
+      - const: misc-latch
+      - const: sw-exception
+      - const: watchdog
+      - const: ce0
+      - const: ce1
+      - const: ce2
+      - const: ce3
+      - const: ce4
+      - const: ce5
+      - const: ce6
+      - const: ce7
+      - const: ce8
+      - const: ce9
+      - const: ce10
+      - const: ce11
+      - const: host2wbm-desc-feed
+      - const: host2reo-re-injection
+      - const: host2reo-command
+      - const: host2rxdma-monitor-ring3
+      - const: host2rxdma-monitor-ring2
+      - const: host2rxdma-monitor-ring1
+      - const: reo2ost-exception
+      - const: wbm2host-rx-release
+      - const: reo2host-status
+      - const: reo2host-destination-ring4
+      - const: reo2host-destination-ring3
+      - const: reo2host-destination-ring2
+      - const: reo2host-destination-ring1
+      - const: rxdma2host-monitor-destination-mac3
+      - const: rxdma2host-monitor-destination-mac2
+      - const: rxdma2host-monitor-destination-mac1
+      - const: ppdu-end-interrupts-mac3
+      - const: ppdu-end-interrupts-mac2
+      - const: ppdu-end-interrupts-mac1
+      - const: rxdma2host-monitor-status-ring-mac3
+      - const: rxdma2host-monitor-status-ring-mac2
+      - const: rxdma2host-monitor-status-ring-mac1
+      - const: host2rxdma-host-buf-ring-mac3
+      - const: host2rxdma-host-buf-ring-mac2
+      - const: host2rxdma-host-buf-ring-mac1
+      - const: rxdma2host-destination-ring-mac3
+      - const: rxdma2host-destination-ring-mac2
+      - const: rxdma2host-destination-ring-mac1
+      - const: host2tcl-input-ring4
+      - const: host2tcl-input-ring3
+      - const: host2tcl-input-ring2
+      - const: host2tcl-input-ring1
+      - const: wbm2host-tx-completions-ring3
+      - const: wbm2host-tx-completions-ring2
+      - const: wbm2host-tx-completions-ring1
+      - const: tcl2host-status-ring
+
+  qcom,rproc:
+    $ref: /schemas/types.yaml#definitions/phandle
+    description:
+      DT entry of q6v5-wcss remoteproc driver.
+      Phandle to a node that can contain the following properties
+        * compatible
+        * reg
+        * reg-names
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+  - qcom,rproc
+
+additionalProperties: false
+
+examples:
+  - |
+
+    q6v5_wcss: q6v5_wcss@CD00000 {
+        compatible = "qcom,ipq8074-wcss-pil";
+        reg = <0xCD00000 0x4040>,
+              <0x4AB000 0x20>;
+        reg-names = "qdsp6",
+                    "rmb";
+    };
+
+    wifi0: wifi@c000000 {
+        compatible = "qcom,ipq8074-wifi";
+        reg = <0xc000000 0x2000000>;
+        interrupts = <0 320 1>,
+                     <0 319 1>,
+                     <0 318 1>,
+                     <0 317 1>,
+                     <0 316 1>,
+                     <0 315 1>,
+                     <0 314 1>,
+                     <0 311 1>,
+                     <0 310 1>,
+                     <0 411 1>,
+                     <0 410 1>,
+                     <0 40 1>,
+                     <0 39 1>,
+                     <0 302 1>,
+                     <0 301 1>,
+                     <0 37 1>,
+                     <0 36 1>,
+                     <0 296 1>,
+                     <0 295 1>,
+                     <0 294 1>,
+                     <0 293 1>,
+                     <0 292 1>,
+                     <0 291 1>,
+                     <0 290 1>,
+                     <0 289 1>,
+                     <0 288 1>,
+                     <0 239 1>,
+                     <0 236 1>,
+                     <0 235 1>,
+                     <0 234 1>,
+                     <0 233 1>,
+                     <0 232 1>,
+                     <0 231 1>,
+                     <0 230 1>,
+                     <0 229 1>,
+                     <0 228 1>,
+                     <0 224 1>,
+                     <0 223 1>,
+                     <0 203 1>,
+                     <0 183 1>,
+                     <0 180 1>,
+                     <0 179 1>,
+                     <0 178 1>,
+                     <0 177 1>,
+                     <0 176 1>,
+                     <0 163 1>,
+                     <0 162 1>,
+                     <0 160 1>,
+                     <0 159 1>,
+                     <0 158 1>,
+                     <0 157 1>,
+                     <0 156 1>;
+        interrupt-names = "misc-pulse1",
+                          "misc-latch",
+                          "sw-exception",
+                          "watchdog",
+                          "ce0",
+                          "ce1",
+                          "ce2",
+                          "ce3",
+                          "ce4",
+                          "ce5",
+                          "ce6",
+                          "ce7",
+                          "ce8",
+                          "ce9",
+                          "ce10",
+                          "ce11",
+                          "host2wbm-desc-feed",
+                          "host2reo-re-injection",
+                          "host2reo-command",
+                          "host2rxdma-monitor-ring3",
+                          "host2rxdma-monitor-ring2",
+                          "host2rxdma-monitor-ring1",
+                          "reo2ost-exception",
+                          "wbm2host-rx-release",
+                          "reo2host-status",
+                          "reo2host-destination-ring4",
+                          "reo2host-destination-ring3",
+                          "reo2host-destination-ring2",
+                          "reo2host-destination-ring1",
+                          "rxdma2host-monitor-destination-mac3",
+                          "rxdma2host-monitor-destination-mac2",
+                          "rxdma2host-monitor-destination-mac1",
+                          "ppdu-end-interrupts-mac3",
+                          "ppdu-end-interrupts-mac2",
+                          "ppdu-end-interrupts-mac1",
+                          "rxdma2host-monitor-status-ring-mac3",
+                          "rxdma2host-monitor-status-ring-mac2",
+                          "rxdma2host-monitor-status-ring-mac1",
+                          "host2rxdma-host-buf-ring-mac3",
+                          "host2rxdma-host-buf-ring-mac2",
+                          "host2rxdma-host-buf-ring-mac1",
+                          "rxdma2host-destination-ring-mac3",
+                          "rxdma2host-destination-ring-mac2",
+                          "rxdma2host-destination-ring-mac1",
+                          "host2tcl-input-ring4",
+                          "host2tcl-input-ring3",
+                          "host2tcl-input-ring2",
+                          "host2tcl-input-ring1",
+                          "wbm2host-tx-completions-ring3",
+                          "wbm2host-tx-completions-ring2",
+                          "wbm2host-tx-completions-ring1",
+                          "tcl2host-status-ring";
+        qcom,rproc = <&q6v5_wcss>;
+    };