Properly trim the vendor tree to include only those files that we want

merged into FreeBSD. Cherry picking from a full vendor tree was too
hard and lead to undestirable svn results.

Note: We only tim the dts* files, we don't trim the dt-bindings tree,
since having all of them causes no problems and the benefit to
trimming there is far out weighed by the cost of doing the trim each
time.

1 files changed, 0 insertions, 538 deletions

diff --git a/src/arm/omap4-panda-common.dtsi b/src/arm/omap4-panda-common.dtsi
deleted file mode 100644
index 8cfa3c8a72b0..000000000000
--- a/src/arm/omap4-panda-common.dtsi
+++ /dev/null
@@ -1,538 +0,0 @@
-/*
- * Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include "elpida_ecb240abacn.dtsi"
-
-/ {
-	model = "TI OMAP4 PandaBoard";
-	compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
-
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>; /* 1 GB */
-	};
-
-	aliases {
-		display0 = &dvi0;
-		display1 = &hdmi0;
-	};
-
-	leds: leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <
-			&led_wkgpio_pins
-		>;
-
-		heartbeat {
-			label = "pandaboard::status1";
-			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		mmc {
-			label = "pandaboard::status2";
-			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-		};
-	};
-
-	sound: sound {
-		compatible = "ti,abe-twl6040";
-		ti,model = "PandaBoard";
-
-		ti,mclk-freq = <38400000>;
-
-		ti,mcpdm = <&mcpdm>;
-
-		ti,twl6040 = <&twl6040>;
-
-		/* Audio routing */
-		ti,audio-routing =
-			"Headset Stereophone", "HSOL",
-			"Headset Stereophone", "HSOR",
-			"Ext Spk", "HFL",
-			"Ext Spk", "HFR",
-			"Line Out", "AUXL",
-			"Line Out", "AUXR",
-			"HSMIC", "Headset Mic",
-			"Headset Mic", "Headset Mic Bias",
-			"AFML", "Line In",
-			"AFMR", "Line In";
-	};
-
-	/* HS USB Port 1 Power */
-	hsusb1_power: hsusb1_power_reg {
-		compatible = "regulator-fixed";
-		regulator-name = "hsusb1_vbus";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio1 1 0>;	/* gpio_1 */
-		startup-delay-us = <70000>;
-		enable-active-high;
-		/*
-		 * boot-on is required along with always-on as the
-		 * regulator framework doesn't enable the regulator
-		 * if boot-on is not there.
-		 */
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
-	/* HS USB Host PHY on PORT 1 */
-	hsusb1_phy: hsusb1_phy {
-		compatible = "usb-nop-xceiv";
-		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
-		vcc-supply = <&hsusb1_power>;
-		clocks = <&auxclk3_ck>;
-		clock-names = "main_clk";
-		clock-frequency = <19200000>;
-	};
-
-	/* regulator for wl12xx on sdio5 */
-	wl12xx_vmmc: wl12xx_vmmc {
-		pinctrl-names = "default";
-		pinctrl-0 = <&wl12xx_gpio>;
-		compatible = "regulator-fixed";
-		regulator-name = "vwl1271";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		gpio = <&gpio2 11 0>;
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-
-	tfp410: encoder@0 {
-		compatible = "ti,tfp410";
-		powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;	/* gpio_0 */
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				tfp410_in: endpoint@0 {
-					remote-endpoint = <&dpi_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-
-				tfp410_out: endpoint@0 {
-					remote-endpoint = <&dvi_connector_in>;
-				};
-			};
-		};
-	};
-
-	dvi0: connector@0 {
-		compatible = "dvi-connector";
-		label = "dvi";
-
-		digital;
-
-		ddc-i2c-bus = <&i2c3>;
-
-		port {
-			dvi_connector_in: endpoint {
-				remote-endpoint = <&tfp410_out>;
-			};
-		};
-	};
-
-	tpd12s015: encoder@1 {
-		compatible = "ti,tpd12s015";
-
-		gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>,	/* 60, CT CP HPD */
-			<&gpio2 9 GPIO_ACTIVE_HIGH>,	/* 41, LS OE */
-			<&gpio2 31 GPIO_ACTIVE_HIGH>;	/* 63, HPD */
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				tpd12s015_in: endpoint@0 {
-					remote-endpoint = <&hdmi_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-
-				tpd12s015_out: endpoint@0 {
-					remote-endpoint = <&hdmi_connector_in>;
-				};
-			};
-		};
-	};
-
-	hdmi0: connector@1 {
-		compatible = "hdmi-connector";
-		label = "hdmi";
-
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&tpd12s015_out>;
-			};
-		};
-	};
-};
-
-&omap4_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <
-			&dss_dpi_pins
-			&tfp410_pins
-			&dss_hdmi_pins
-			&tpd12s015_pins
-			&hsusbb1_pins
-	>;
-
-	twl6040_pins: pinmux_twl6040_pins {
-		pinctrl-single,pins = <
-			0xe0 (PIN_OUTPUT | MUX_MODE3)	/* hdq_sio.gpio_127 */
-			0x160 (PIN_INPUT | MUX_MODE0)	/* sys_nirq2.sys_nirq2 */
-		>;
-	};
-
-	mcpdm_pins: pinmux_mcpdm_pins {
-		pinctrl-single,pins = <
-			0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_pdm_ul_data.abe_pdm_ul_data */
-			0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_pdm_dl_data.abe_pdm_dl_data */
-			0xca (PIN_INPUT_PULLUP   | MUX_MODE0)	/* abe_pdm_frame.abe_pdm_frame */
-			0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_pdm_lb_clk.abe_pdm_lb_clk */
-			0xce (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_clks.abe_clks */
-		>;
-	};
-
-	mcbsp1_pins: pinmux_mcbsp1_pins {
-		pinctrl-single,pins = <
-			0xbe (PIN_INPUT | MUX_MODE0)		/* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
-			0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* abe_mcbsp1_dr.abe_mcbsp1_dr */
-			0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* abe_mcbsp1_dx.abe_mcbsp1_dx */
-			0xc4 (PIN_INPUT | MUX_MODE0)		/* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
-		>;
-	};
-
-	dss_dpi_pins: pinmux_dss_dpi_pins {
-		pinctrl-single,pins = <
-			0x122 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data23 */
-			0x124 (PIN_OUTPUT | MUX_MODE5) 	/* dispc2_data22 */
-			0x126 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data21 */
-			0x128 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data20 */
-			0x12a (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data19 */
-			0x12c (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data18 */
-			0x12e (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data15 */
-			0x130 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data14 */
-			0x132 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data13 */
-			0x134 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data12 */
-			0x136 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data11 */
-
-			0x174 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data10 */
-			0x176 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data9 */
-			0x178 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data16 */
-			0x17a (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data17 */
-			0x17c (PIN_OUTPUT | MUX_MODE5)	/* dispc2_hsync */
-			0x17e (PIN_OUTPUT | MUX_MODE5)	/* dispc2_pclk */
-			0x180 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_vsync */
-			0x182 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_de */
-			0x184 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data8 */
-			0x186 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data7 */
-			0x188 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data6 */
-			0x18a (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data5 */
-			0x18c (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data4 */
-			0x18e (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data3 */
-
-			0x190 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data2 */
-			0x192 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data1 */
-			0x194 (PIN_OUTPUT | MUX_MODE5)	/* dispc2_data0 */
-		>;
-	};
-
-	tfp410_pins: pinmux_tfp410_pins {
-		pinctrl-single,pins = <
-			0x144 (PIN_OUTPUT | MUX_MODE3)	/* gpio_0 */
-		>;
-	};
-
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
-		pinctrl-single,pins = <
-			0x5a (PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_cec.hdmi_cec */
-			0x5c (PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_scl.hdmi_scl */
-			0x5e (PIN_INPUT_PULLUP | MUX_MODE0)	/* hdmi_sda.hdmi_sda */
-		>;
-	};
-
-	tpd12s015_pins: pinmux_tpd12s015_pins {
-		pinctrl-single,pins = <
-			0x22 (PIN_OUTPUT | MUX_MODE3)		/* gpmc_a17.gpio_41 */
-			0x48 (PIN_OUTPUT | MUX_MODE3)		/* gpmc_nbe1.gpio_60 */
-			0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* hdmi_hpd.gpio_63 */
-		>;
-	};
-
-	hsusbb1_pins: pinmux_hsusbb1_pins {
-		pinctrl-single,pins = <
-			0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
-			0x84 (PIN_OUTPUT | MUX_MODE4)		/* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
-			0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
-			0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
-			0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
-			0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
-			0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
-			0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
-			0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
-			0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
-			0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
-			0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
-		>;
-	};
-
-	i2c1_pins: pinmux_i2c1_pins {
-		pinctrl-single,pins = <
-			0xe2 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
-			0xe4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda */
-		>;
-	};
-
-	i2c2_pins: pinmux_i2c2_pins {
-		pinctrl-single,pins = <
-			0xe6 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_scl */
-			0xe8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c2_sda */
-		>;
-	};
-
-	i2c3_pins: pinmux_i2c3_pins {
-		pinctrl-single,pins = <
-			0xea (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_scl */
-			0xec (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c3_sda */
-		>;
-	};
-
-	i2c4_pins: pinmux_i2c4_pins {
-		pinctrl-single,pins = <
-			0xee (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_scl */
-			0xf0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
-		>;
-	};
-
-	/*
-	 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
-	 * REVISIT: Are the pull-ups needed for GPIO 48 and 49?
-	 */
-	wl12xx_gpio: pinmux_wl12xx_gpio {
-		pinctrl-single,pins = <
-			0x26 (PIN_OUTPUT | MUX_MODE3)		/* gpmc_a19.gpio_43 */
-			0x2c (PIN_OUTPUT | MUX_MODE3)		/* gpmc_a22.gpio_46 */
-			0x30 (PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_a24.gpio_48 */
-			0x32 (PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_a25.gpio_49 */
-		>;
-	};
-
-	/* wl12xx GPIO inputs and SDIO pins */
-	wl12xx_pins: pinmux_wl12xx_pins {
-		pinctrl-single,pins = <
-			0x38 (PIN_INPUT | MUX_MODE3)		/* gpmc_ncs2.gpio_52 */
-			0x3a (PIN_INPUT | MUX_MODE3)		/* gpmc_ncs3.gpio_53 */
-			0x108 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_clk.sdmmc5_clk */
-			0x10a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_cmd.sdmmc5_cmd */
-			0x10c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat0.sdmmc5_dat0 */
-			0x10e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat1.sdmmc5_dat1 */
-			0x110 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat2.sdmmc5_dat2 */
-			0x112 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat3.sdmmc5_dat3 */
-		>;
-	};
-};
-
-&omap4_pmx_wkup {
-	led_wkgpio_pins: pinmux_leds_wkpins {
-		pinctrl-single,pins = <
-			0x1a (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk7 */
-			0x1c (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk8 */
-		>;
-	};
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
-
-	clock-frequency = <400000>;
-
-	twl: twl@48 {
-		reg = <0x48>;
-		/* IRQ# = 7 */
-		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
-		interrupt-parent = <&gic>;
-	};
-
-	twl6040: twl@4b {
-		compatible = "ti,twl6040";
-		reg = <0x4b>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&twl6040_pins>;
-
-		/* IRQ# = 119 */
-		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
-		interrupt-parent = <&gic>;
-		ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>;  /* gpio line 127 */
-
-		vio-supply = <&v1v8>;
-		v2v1-supply = <&v2v1>;
-		enable-active-high;
-	};
-};
-
-#include "twl6030.dtsi"
-#include "twl6030_omap4.dtsi"
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
-
-	clock-frequency = <400000>;
-};
-
-&i2c3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c3_pins>;
-
-	clock-frequency = <100000>;
-
-	/*
-	 * Display monitor features are burnt in their EEPROM as EDID data.
-	 * The EEPROM is connected as I2C slave device.
-	 */
-	eeprom@50 {
-		compatible = "ti,eeprom";
-		reg = <0x50>;
-	};
-};
-
-&i2c4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c4_pins>;
-
-	clock-frequency = <400000>;
-};
-
-&mmc1 {
-	vmmc-supply = <&vmmc>;
-	bus-width = <8>;
-};
-
-&mmc2 {
-	status = "disabled";
-};
-
-&mmc3 {
-	status = "disabled";
-};
-
-&mmc4 {
-	status = "disabled";
-};
-
-&mmc5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&wl12xx_pins>;
-	vmmc-supply = <&wl12xx_vmmc>;
-	non-removable;
-	bus-width = <4>;
-	cap-power-off-card;
-};
-
-&emif1 {
-	cs1-used;
-	device-handle = <&elpida_ECB240ABACN>;
-};
-
-&emif2 {
-	cs1-used;
-	device-handle = <&elpida_ECB240ABACN>;
-};
-
-&mcbsp1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp1_pins>;
-	status = "okay";
-};
-
-&mcpdm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcpdm_pins>;
-	status = "okay";
-};
-
-&twl_usb_comparator {
-	usb-supply = <&vusb>;
-};
-
-&uart2 {
-	interrupts-extended = <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core OMAP4_UART2_RX>;
-};
-
-&uart3 {
-	interrupts-extended = <&gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core OMAP4_UART3_RX>;
-};
-
-&uart4 {
-	interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core OMAP4_UART4_RX>;
-};
-
-&usb_otg_hs {
-	interface-type = <1>;
-	mode = <3>;
-	power = <50>;
-};
-
-&usbhshost {
-	port1-mode = "ehci-phy";
-};
-
-&usbhsehci {
-	phys = <&hsusb1_phy>;
-};
-
-&dss {
-	status = "ok";
-
-	port {
-		dpi_out: endpoint {
-			remote-endpoint = <&tfp410_in>;
-			data-lines = <24>;
-		};
-	};
-};
-
-&dsi2 {
-	status = "ok";
-	vdd-supply = <&vcxio>;
-};
-
-&hdmi {
-	status = "ok";
-	vdda-supply = <&vdac>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&tpd12s015_in>;
-		};
-	};
-};