diff options
Diffstat (limited to 'Bindings/display/ste,mcde.txt')
| -rw-r--r-- | Bindings/display/ste,mcde.txt | 104 |
1 files changed, 104 insertions, 0 deletions
diff --git a/Bindings/display/ste,mcde.txt b/Bindings/display/ste,mcde.txt new file mode 100644 index 000000000000..4c33c692bd5f --- /dev/null +++ b/Bindings/display/ste,mcde.txt @@ -0,0 +1,104 @@ +ST-Ericsson Multi Channel Display Engine MCDE + +The ST-Ericsson MCDE is a display controller with support for compositing +and displaying several channels memory resident graphics data on DSI or +LCD displays or bridges. It is used in the ST-Ericsson U8500 platform. + +Required properties: + +- compatible: must be: + "ste,mcde" +- reg: register base for the main MCDE control registers, should be + 0x1000 in size +- interrupts: the interrupt line for the MCDE +- epod-supply: a phandle to the EPOD regulator +- vana-supply: a phandle to the analog voltage regulator +- clocks: an array of the MCDE clocks in this strict order: + MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI + (HDMI clock), DSI0ESCLK (DSI0 energy save clock), + DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy + save clock) +- clock-names: must be the following array: + "mcde", "lcd", "hdmi" + to match the required clock inputs above. +- #address-cells: should be <1> (for the DSI hosts that will be children) +- #size-cells: should be <1> (for the DSI hosts that will be children) +- ranges: this should always be stated + +Required subnodes: + +The devicetree must specify subnodes for the DSI host adapters. +These must have the following characteristics: + +- compatible: must be: + "ste,mcde-dsi" +- reg: must specify the register range for the DSI host +- vana-supply: phandle to the VANA voltage regulator +- clocks: phandles to the high speed and low power (energy save) clocks + the high speed clock is not present on the third (dsi2) block, so it + should only have the "lp" clock +- clock-names: "hs" for the high speed clock and "lp" for the low power + (energy save) clock +- #address-cells: should be <1> +- #size-cells: should be <0> + +Display panels and bridges will appear as children on the DSI hosts, and +the displays are connected to the DSI hosts using the common binding +for video transmitter interfaces; see +Documentation/devicetree/bindings/media/video-interfaces.txt + +If a DSI host is unused (not connected) it will have no children defined. + +Example: + +mcde@a0350000 { + compatible = "ste,mcde"; + reg = <0xa0350000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + epod-supply = <&db8500_b2r2_mcde_reg>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */ + <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */ + <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */ + clock-names = "mcde", "lcd", "hdmi"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dsi0: dsi@a0351000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0351000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>; + clock-names = "hs", "lp"; + #address-cells = <1>; + #size-cells = <0>; + + panel { + compatible = "samsung,s6d16d0"; + reg = <0>; + vdd1-supply = <&ab8500_ldo_aux1_reg>; + reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + }; + + }; + dsi1: dsi@a0352000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0352000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>; + clock-names = "hs", "lp"; + #address-cells = <1>; + #size-cells = <0>; + }; + dsi2: dsi@a0353000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0353000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + /* This DSI port only has the Low Power / Energy Save clock */ + clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>; + clock-names = "lp"; + #address-cells = <1>; + #size-cells = <0>; + }; +}; |