diff options
Diffstat (limited to 'Bindings/display')
46 files changed, 1418 insertions, 78 deletions
diff --git a/Bindings/display/amlogic,meson-vpu.txt b/Bindings/display/amlogic,meson-vpu.txt new file mode 100644 index 000000000000..00f74bad1e95 --- /dev/null +++ b/Bindings/display/amlogic,meson-vpu.txt @@ -0,0 +1,112 @@ +Amlogic Meson Display Controller +================================ + +The Amlogic Meson Display controller is composed of several components +that are going to be documented below: + +DMC|---------------VPU (Video Processing Unit)----------------|------HHI------| + | vd1 _______ _____________ _________________ | | +D |-------| |----| | | | | HDMI PLL | +D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK | +R |-------| |----| Processing | | | | | + | osd2 | | | |---| Enci ----------|----|-----VDAC------| +R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----| +A | osd1 | | | Blenders | | Encl ----------|----|---------------| +M |-------|______|----|____________| |________________| | | +___|__________________________________________________________|_______________| + + +VIU: Video Input Unit +--------------------- + +The Video Input Unit is in charge of the pixel scanout from the DDR memory. +It fetches the frames addresses, stride and parameters from the "Canvas" memory. +This part is also in charge of the CSC (Colorspace Conversion). +It can handle 2 OSD Planes and 2 Video Planes. + +VPP: Video Post Processing +-------------------------- + +The Video Post Processing is in charge of the scaling and blending of the +various planes into a single pixel stream. +There is a special "pre-blending" used by the video planes with a dedicated +scaler and a "post-blending" to merge with the OSD Planes. +The OSD planes also have a dedicated scaler for one of the OSD. + +VENC: Video Encoders +-------------------- + +The VENC is composed of the multiple pixel encoders : + - ENCI : Interlace Video encoder for CVBS and Interlace HDMI + - ENCP : Progressive Video Encoder for HDMI + - ENCL : LCD LVDS Encoder +The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock +tree and provides the scanout clock to the VPP and VIU. +The ENCI is connected to a single VDAC for Composite Output. +The ENCI and ENCP are connected to an on-chip HDMI Transceiver. + +Device Tree Bindings: +--------------------- + +VPU: Video Processing Unit +-------------------------- + +Required properties: +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,meson-gxbb-vpu" + - GXL (S905X, S905D) : "amlogic,meson-gxl-vpu" + - GXM (S912) : "amlogic,meson-gxm-vpu" + followed by the common "amlogic,meson-gx-vpu" +- reg: base address and size of he following memory-mapped regions : + - vpu + - hhi + - dmc +- reg-names: should contain the names of the previous memory regions +- interrupts: should contain the VENC Vsync interrupt number + +Required nodes: + +The connections to the VPU output video ports are modeled using the OF graph +bindings specified in Documentation/devicetree/bindings/graph.txt. + +The following table lists for each supported model the port number +corresponding to each VPU output. + + Port 0 Port 1 +----------------------------------------- + S905 (GXBB) CVBS VDAC HDMI-TX + S905X (GXL) CVBS VDAC HDMI-TX + S905D (GXL) CVBS VDAC HDMI-TX + S912 (GXM) CVBS VDAC HDMI-TX + +Example: + +tv-connector { + compatible = "composite-video-connector"; + + port { + tv_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; +}; + +vpu: vpu@d0100000 { + compatible = "amlogic,meson-gxbb-vpu"; + reg = <0x0 0xd0100000 0x0 0x100000>, + <0x0 0xc883c000 0x0 0x1000>, + <0x0 0xc8838000 0x0 0x1000>; + reg-names = "vpu", "hhi", "dmc"; + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + + /* CVBS VDAC output port */ + port@0 { + reg = <0>; + + cvbs_vdac_out: endpoint { + remote-endpoint = <&tv_connector_in>; + }; + }; +}; diff --git a/Bindings/display/arm,malidp.txt b/Bindings/display/arm,malidp.txt new file mode 100644 index 000000000000..2f7870983ef1 --- /dev/null +++ b/Bindings/display/arm,malidp.txt @@ -0,0 +1,65 @@ +ARM Mali-DP + +The following bindings apply to a family of Display Processors sold as +licensable IP by ARM Ltd. The bindings describe the Mali DP500, DP550 and +DP650 processors that offer multiple composition layers, support for +rotation and scaling output. + +Required properties: + - compatible: should be one of + "arm,mali-dp500" + "arm,mali-dp550" + "arm,mali-dp650" + depending on the particular implementation present in the hardware + - reg: Physical base address and size of the block of registers used by + the processor. + - interrupts: Interrupt list, as defined in ../interrupt-controller/interrupts.txt, + interrupt client nodes. + - interrupt-names: name of the engine inside the processor that will + use the corresponding interrupt. Should be one of "DE" or "SE". + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. It should contain: + - "pclk": for the APB interface clock + - "aclk": for the AXI interface clock + - "mclk": for the main processor clock + - "pxlclk": for the pixel clock feeding the output PLL of the processor. + - arm,malidp-output-port-lines: Array of u8 values describing the number + of output lines per channel (R, G and B). + +Required sub-nodes: + - port: The Mali DP connection to an encoder input port. The connection + is modelled using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for the framebuffer; if not present, the framebuffer may + be located anywhere in memory. + + +Example: + +/ { + ... + + dp0: malidp@6f200000 { + compatible = "arm,mali-dp650"; + reg = <0 0x6f200000 0 0x20000>; + memory-region = <&display_reserved>; + interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>, + <0 168 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "DE", "SE"; + clocks = <&oscclk2>, <&fpgaosc0>, <&fpgaosc1>, <&fpgaosc1>; + clock-names = "pxlclk", "mclk", "aclk", "pclk"; + arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; + port { + dp0_output: endpoint { + remote-endpoint = <&tda998x_2_input>; + }; + }; + }; + + ... +}; diff --git a/Bindings/display/brcm,bcm-vc4.txt b/Bindings/display/brcm,bcm-vc4.txt index a5ea451e67fc..e2768703ac2b 100644 --- a/Bindings/display/brcm,bcm-vc4.txt +++ b/Bindings/display/brcm,bcm-vc4.txt @@ -43,6 +43,13 @@ Required properties for DPI: - port: Port node with a single endpoint connecting to the panel device, as defined in [1] +Required properties for VEC: +- compatible: Should be "brcm,bcm2835-vec" +- reg: Physical base address and length of the registers +- clocks: The core clock the unit runs on +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt + Required properties for V3D: - compatible: Should be "brcm,bcm2835-v3d" - reg: Physical base address and length of the V3D's registers @@ -92,6 +99,13 @@ dpi: dpi@7e208000 { }; }; +vec: vec@7e806000 { + compatible = "brcm,bcm2835-vec"; + reg = <0x7e806000 0x1000>; + clocks = <&clocks BCM2835_CLOCK_VEC>; + interrupts = <2 27>; +}; + v3d: v3d@7ec00000 { compatible = "brcm,bcm2835-v3d"; reg = <0x7ec00000 0x1000>; diff --git a/Bindings/display/bridge/adi,adv7511.txt b/Bindings/display/bridge/adi,adv7511.txt index 96c25ee01501..6532a59c9b43 100644 --- a/Bindings/display/bridge/adi,adv7511.txt +++ b/Bindings/display/bridge/adi,adv7511.txt @@ -1,13 +1,19 @@ -Analog Device ADV7511(W)/13 HDMI Encoders +Analog Device ADV7511(W)/13/33 HDMI Encoders ----------------------------------------- -The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters +The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space conversion, -S/PDIF, CEC and HDCP. +S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while +the others support RGB interface. Required properties: -- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513" +- compatible: Should be one of: + "adi,adv7511" + "adi,adv7511w" + "adi,adv7513" + "adi,adv7533" + - reg: I2C slave address The ADV7511 supports a large number of input data formats that differ by their @@ -32,6 +38,11 @@ The following input format properties are required except in "rgb 1x" and - adi,input-justification: The input bit justification ("left", "evenly", "right"). +The following properties are required for ADV7533: + +- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should + be one of 1, 2, 3 or 4. + Optional properties: - interrupts: Specifier for the ADV7511 interrupt @@ -42,13 +53,18 @@ Optional properties: - adi,embedded-sync: The input uses synchronization signals embedded in the data stream (similar to BT.656). Defaults to separate H/V synchronization signals. +- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing + generator. The chip will rely on the sync signals in the DSI data lanes, + rather than generate its own timings for HDMI output. Required nodes: The ADV7511 has two video ports. Their connections are modelled using the OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. -- Video port 0 for the RGB or YUV input +- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the + remote endpoint phandle should be a reference to a valid mipi_dsi_host device + node. - Video port 1 for the HDMI output diff --git a/Bindings/display/bridge/analogix_dp.txt b/Bindings/display/bridge/analogix_dp.txt index 4f2ba8c13d92..4a0f4f7682ad 100644 --- a/Bindings/display/bridge/analogix_dp.txt +++ b/Bindings/display/bridge/analogix_dp.txt @@ -5,6 +5,7 @@ Required properties for dp-controller: platform specific such as: * "samsung,exynos5-dp" * "rockchip,rk3288-dp" + * "rockchip,rk3399-edp" -reg: physical base address of the controller and length of memory mapped region. diff --git a/Bindings/display/bridge/dumb-vga-dac.txt b/Bindings/display/bridge/dumb-vga-dac.txt new file mode 100644 index 000000000000..164cbb15f04c --- /dev/null +++ b/Bindings/display/bridge/dumb-vga-dac.txt @@ -0,0 +1,50 @@ +Dumb RGB to VGA DAC bridge +--------------------------- + +This binding is aimed for dumb RGB to VGA DAC based bridges that do not require +any configuration. + +Required properties: + +- compatible: Must be "dumb-vga-dac" + +Required nodes: + +This device has two video ports. Their connections are modelled using the OF +graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for RGB input +- Video port 1 for VGA output + +Optional properties: +- vdd-supply: Power supply for DAC + +Example +------- + +bridge { + compatible = "dumb-vga-dac"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + vga_bridge_in: endpoint { + remote-endpoint = <&tcon0_out_vga>; + }; + }; + + port@1 { + reg = <1>; + + vga_bridge_out: endpoint { + remote-endpoint = <&vga_con_in>; + }; + }; + }; +}; diff --git a/Bindings/display/bridge/dw_hdmi.txt b/Bindings/display/bridge/dw_hdmi.txt index dc1452f0d5d8..5e9a84d6e5f1 100644 --- a/Bindings/display/bridge/dw_hdmi.txt +++ b/Bindings/display/bridge/dw_hdmi.txt @@ -19,7 +19,9 @@ Required properties: Optional properties - reg-io-width: the width of the reg:1,4, default set to 1 if not present -- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing +- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing, + if the property is omitted, a functionally reduced I2C bus + controller on DW HDMI is probed - clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" Example: diff --git a/Bindings/display/bridge/sii902x.txt b/Bindings/display/bridge/sii902x.txt new file mode 100644 index 000000000000..56a3e68ccb80 --- /dev/null +++ b/Bindings/display/bridge/sii902x.txt @@ -0,0 +1,35 @@ +sii902x HDMI bridge bindings + +Required properties: + - compatible: "sil,sii9022" + - reg: i2c address of the bridge + +Optional properties: + - interrupts-extended or interrupt-parent + interrupts: describe + the interrupt line used to inform the host about hotplug events. + - reset-gpios: OF device-tree gpio specification for RST_N pin. + +Optional subnodes: + - video input: this subnode can contain a video input port node + to connect the bridge to a display controller output (See this + documentation [1]). + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + hdmi-bridge@39 { + compatible = "sil,sii9022"; + reg = <0x39>; + reset-gpios = <&pioA 1 0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + bridge_in: endpoint { + remote-endpoint = <&dc_out>; + }; + }; + }; + }; diff --git a/Bindings/display/bridge/tda998x.txt b/Bindings/display/bridge/tda998x.txt index e178e6b9f9ee..24cc2466185a 100644 --- a/Bindings/display/bridge/tda998x.txt +++ b/Bindings/display/bridge/tda998x.txt @@ -21,8 +21,19 @@ Optional properties: - video-ports: 24 bits value which defines how the video controller output is wired to the TDA998x input - default: <0x230145> + - audio-ports: array of 8-bit values, 2 values per one DAI[1]. + The first value defines the DAI type: TDA998x_SPDIF or TDA998x_I2S[2]. + The second value defines the tda998x AP_ENA reg content when the DAI + in question is used. The implementation allows one or two DAIs. If two + DAIs are defined, they must be of different type. + +[1] Documentation/sound/alsa/soc/DAI.txt +[2] include/dt-bindings/display/tda998x.h + Example: +#include <dt-bindings/display/tda998x.h> + tda998x: hdmi-encoder { compatible = "nxp,tda998x"; reg = <0x70>; @@ -30,4 +41,11 @@ Example: interrupts = <27 2>; /* falling edge */ pinctrl-0 = <&pmx_camera>; pinctrl-names = "default"; + video-ports = <0x230145>; + + #sound-dai-cells = <2>; + /* DAI-format AP_ENA reg value */ + audio-ports = < TDA998x_SPDIF 0x04 + TDA998x_I2S 0x03>; + }; diff --git a/Bindings/display/bridge/ti,tfp410.txt b/Bindings/display/bridge/ti,tfp410.txt new file mode 100644 index 000000000000..54d7e31525ec --- /dev/null +++ b/Bindings/display/bridge/ti,tfp410.txt @@ -0,0 +1,46 @@ +TFP410 DPI to DVI encoder +========================= + +Required properties: +- compatible: "ti,tfp410" + +Optional properties: +- powerdown-gpios: power-down gpio +- reg: I2C address. If and only if present the device node + should be placed into the i2c controller node where the + tfp410 i2c is connected to. + +Required nodes: +- Video port 0 for DPI input [1]. +- Video port 1 for DVI output [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example +------- + +tfp410: encoder@0 { + compatible = "ti,tfp410"; + powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tfp410_in: endpoint@0 { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + + tfp410_out: endpoint@0 { + remote-endpoint = <&dvi_connector_in>; + }; + }; + }; +}; diff --git a/Bindings/display/bridge/toshiba,tc358767.txt b/Bindings/display/bridge/toshiba,tc358767.txt new file mode 100644 index 000000000000..e3f6aa6a214d --- /dev/null +++ b/Bindings/display/bridge/toshiba,tc358767.txt @@ -0,0 +1,53 @@ +Toshiba TC358767 eDP bridge bindings + +Required properties: + - compatible: "toshiba,tc358767" + - reg: i2c address of the bridge, 0x68 or 0x0f, depending on bootstrap pins + - clock-names: should be "ref" + - clocks: OF device-tree clock specification for refclk input. The reference + clock rate must be 13 MHz, 19.2 MHz, 26 MHz, or 38.4 MHz. + +Optional properties: + - shutdown-gpios: OF device-tree gpio specification for SD pin + (active high shutdown input) + - reset-gpios: OF device-tree gpio specification for RSTX pin + (active low system reset) + - ports: the ports node can contain video interface port nodes to connect + to a DPI/DSI source and to an eDP/DP sink according to [1][2]: + - port@0: DSI input port + - port@1: DPI input port + - port@2: eDP/DP output port + +[1]: Documentation/devicetree/bindings/graph.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + edp-bridge@68 { + compatible = "toshiba,tc358767"; + reg = <0x68>; + shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>; + clock-names = "ref"; + clocks = <&edp_refclk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + bridge_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + port@2 { + reg = <2>; + + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Bindings/display/cirrus,clps711x-fb.txt b/Bindings/display/cirrus,clps711x-fb.txt index d685be898d0c..e9c65746e2f1 100644 --- a/Bindings/display/cirrus,clps711x-fb.txt +++ b/Bindings/display/cirrus,clps711x-fb.txt @@ -1,7 +1,7 @@ * Currus Logic CLPS711X Framebuffer Required properties: -- compatible: Shall contain "cirrus,clps711x-fb". +- compatible: Shall contain "cirrus,ep7209-fb". - reg : Physical base address and length of the controller's registers + location and size of the framebuffer memory. - clocks : phandle + clock specifier pair of the FB reference clock. @@ -18,7 +18,7 @@ Optional properties: Example: fb: fb@800002c0 { - compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb"; + compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb"; reg = <0x800002c0 0xd44>, <0x60000000 0xc000>; clocks = <&clks 2>; lcd-supply = <®5v0>; diff --git a/Bindings/display/connector/hdmi-connector.txt b/Bindings/display/connector/hdmi-connector.txt index acd5668b1ce1..508aee461e0d 100644 --- a/Bindings/display/connector/hdmi-connector.txt +++ b/Bindings/display/connector/hdmi-connector.txt @@ -8,6 +8,7 @@ Required properties: Optional properties: - label: a symbolic name for the connector - hpd-gpios: HPD GPIO number +- ddc-i2c-bus: phandle link to the I2C controller used for DDC EDID probing Required nodes: - Video port for HDMI input diff --git a/Bindings/display/exynos/exynos_hdmi.txt b/Bindings/display/exynos/exynos_hdmi.txt index a2ec4c1c9382..6394ea9e3b9e 100644 --- a/Bindings/display/exynos/exynos_hdmi.txt +++ b/Bindings/display/exynos/exynos_hdmi.txt @@ -9,7 +9,7 @@ Required properties: - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. -- hpd-gpio: following information about the hotplug gpio pin. +- hpd-gpios: following information about the hotplug gpio pin. a) phandle of the gpio controller node. b) pin number within the gpio controller. c) optional flags and pull up/down. @@ -56,7 +56,7 @@ Example: compatible = "samsung,exynos4212-hdmi"; reg = <0x14530000 0x100000>; interrupts = <0 95 0>; - hpd-gpio = <&gpx3 7 1>; + hpd-gpios = <&gpx3 7 1>; ddc = <&hdmi_ddc_node>; phy = <&hdmi_phy_node>; samsung,syscon-phandle = <&pmu_system_controller>; diff --git a/Bindings/display/fsl,dcu.txt b/Bindings/display/fsl,dcu.txt index ae55cde1b69e..63ec2a624aa9 100644 --- a/Bindings/display/fsl,dcu.txt +++ b/Bindings/display/fsl,dcu.txt @@ -12,7 +12,7 @@ Required properties: - clock-names: Should be "dcu" and "pix" See ../clocks/clock-bindings.txt for details. - big-endian Boolean property, LS1021A DCU registers are big-endian. -- fsl,panel: The phandle to panel node. +- port Video port for the panel output Optional properties: - fsl,tcon: The phandle to the timing controller node. @@ -24,6 +24,11 @@ dcu: dcu@2ce0000 { clocks = <&platform_clk 0>, <&platform_clk 0>; clock-names = "dcu", "pix"; big-endian; - fsl,panel = <&panel>; fsl,tcon = <&tcon>; + + port { + dcu_out: endpoint { + remote-endpoint = <&panel_out>; + }; + }; }; diff --git a/Bindings/display/ht16k33.txt b/Bindings/display/ht16k33.txt new file mode 100644 index 000000000000..8e5b30b87754 --- /dev/null +++ b/Bindings/display/ht16k33.txt @@ -0,0 +1,42 @@ +Holtek ht16k33 RAM mapping 16*8 LED controller driver with keyscan +------------------------------------------------------------------------------- + +Required properties: +- compatible: "holtek,ht16k33" +- reg: I2C slave address of the chip. +- interrupt-parent: A phandle pointing to the interrupt controller + serving the interrupt for this chip. +- interrupts: Interrupt specification for the key pressed interrupt. +- refresh-rate-hz: Display update interval in HZ. +- debounce-delay-ms: Debouncing interval time in milliseconds. +- linux,keymap: The keymap for keys as described in the binding + document (devicetree/bindings/input/matrix-keymap.txt). + +Optional properties: +- linux,no-autorepeat: Disable keyrepeat. +- default-brightness-level: Initial brightness level [0-15] (default: 15). + +Example: + +&i2c1 { + ht16k33: ht16k33@70 { + compatible = "holtek,ht16k33"; + reg = <0x70>; + refresh-rate-hz = <20>; + debounce-delay-ms = <50>; + interrupt-parent = <&gpio4>; + interrupts = <5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; + linux,keymap = < + MATRIX_KEY(2, 0, KEY_F6) + MATRIX_KEY(3, 0, KEY_F8) + MATRIX_KEY(4, 0, KEY_F10) + MATRIX_KEY(5, 0, KEY_F4) + MATRIX_KEY(6, 0, KEY_F2) + MATRIX_KEY(2, 1, KEY_F5) + MATRIX_KEY(3, 1, KEY_F7) + MATRIX_KEY(4, 1, KEY_F9) + MATRIX_KEY(5, 1, KEY_F3) + MATRIX_KEY(6, 1, KEY_F1) + >; + }; +}; diff --git a/Bindings/display/mediatek/mediatek,hdmi.txt b/Bindings/display/mediatek/mediatek,hdmi.txt new file mode 100644 index 000000000000..7b124242b0c5 --- /dev/null +++ b/Bindings/display/mediatek/mediatek,hdmi.txt @@ -0,0 +1,148 @@ +Mediatek HDMI Encoder +===================== + +The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from +its parallel input. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi". +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "pll", "bclk", and "spdif". +- phys: phandle link to the HDMI PHY node. + See Documentation/devicetree/bindings/phy/phy-bindings.txt for details. +- phy-names: must contain "hdmi" +- mediatek,syscon-hdmi: phandle link and register offset to the system + configuration registers. For mt8173 this must be offset 0x900 into the + MMSYS_CONFIG region: <&mmsys 0x900>. +- ports: A node containing input and output port nodes with endpoint + definitions as documented in Documentation/devicetree/bindings/graph.txt. +- port@0: The input port in the ports node should be connected to a DPI output + port. +- port@1: The output port in the ports node should be connected to the input + port of a connector node that contains a ddc-i2c-bus property, or to the + input port of an attached bridge chip, such as a SlimPort transmitter. + +HDMI CEC +======== + +The HDMI CEC controller handles hotplug detection and CEC communication. + +Required properties: +- compatible: Should be "mediatek,<chip>-cec" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clock + +HDMI DDC +======== + +The HDMI DDC i2c controller is used to interface with the HDMI DDC pins. +The Mediatek's I2C controller is used to interface with I2C devices. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi-ddc" +- reg: Physical base address and length of the controller's registers +- clocks: device clock +- clock-names: Should be "ddc-i2c". + +HDMI PHY +======== + +The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel +output and drives the HDMI pads. + +Required properties: +- compatible: "mediatek,<chip>-hdmi-phy" +- reg: Physical base address and length of the module's registers +- clocks: PLL reference clock +- clock-names: must contain "pll_ref" +- clock-output-names: must be "hdmitx_dig_cts" on mt8173 +- #phy-cells: must be <0> +- #clock-cells: must be <0> + +Optional properties: +- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa +- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c + +Example: + +cec: cec@10013000 { + compatible = "mediatek,mt8173-cec"; + reg = <0 0x10013000 0 0xbc>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_CEC>; +}; + +hdmi_phy: hdmi-phy@10209100 { + compatible = "mediatek,mt8173-hdmi-phy"; + reg = <0 0x10209100 0 0x24>; + clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>; + clock-names = "pll_ref"; + clock-output-names = "hdmitx_dig_cts"; + mediatek,ibias = <0xa>; + mediatek,ibias_up = <0x1c>; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +hdmi_ddc0: i2c@11012000 { + compatible = "mediatek,mt8173-hdmi-ddc"; + reg = <0 0x11012000 0 0x1c>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_I2C5>; + clock-names = "ddc-i2c"; +}; + +hdmi0: hdmi@14025000 { + compatible = "mediatek,mt8173-hdmi"; + reg = <0 0x14025000 0 0x400>; + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_HDMI_PIXEL>, + <&mmsys CLK_MM_HDMI_PLLCK>, + <&mmsys CLK_MM_HDMI_AUDIO>, + <&mmsys CLK_MM_HDMI_SPDIF>; + clock-names = "pixel", "pll", "bclk", "spdif"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pin>; + phys = <&hdmi_phy>; + phy-names = "hdmi"; + mediatek,syscon-hdmi = <&mmsys 0x900>; + assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>; + assigned-clock-parents = <&hdmi_phy>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi0_in: endpoint { + remote-endpoint = <&dpi0_out>; + }; + }; + + port@1 { + reg = <1>; + + hdmi0_out: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + }; +}; + +connector { + compatible = "hdmi-connector"; + type = "a"; + ddc-i2c-bus = <&hdmiddc0>; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; +}; diff --git a/Bindings/display/msm/dsi.txt b/Bindings/display/msm/dsi.txt index f5948c48b9a2..6b1cab17f52d 100644 --- a/Bindings/display/msm/dsi.txt +++ b/Bindings/display/msm/dsi.txt @@ -11,8 +11,7 @@ Required properties: be 0 or 1, since we have 2 DSI controllers at most for now. - interrupts: The interrupt signal from the DSI block. - power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clocks: Phandles to device clocks. - clock-names: the following clocks are required: * "mdp_core_clk" * "iface_clk" @@ -23,16 +22,21 @@ Required properties: * "core_clk" For DSIv2, we need an additional clock: * "src_clk" +- assigned-clocks: Parents of "byte_clk" and "pixel_clk" for the given platform. +- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided + by a DSI PHY block. See [1] for details on clock bindings. - vdd-supply: phandle to vdd regulator device node - vddio-supply: phandle to vdd-io regulator device node - vdda-supply: phandle to vdda regulator device node -- qcom,dsi-phy: phandle to DSI PHY device node +- phys: phandle to DSI PHY device node +- phy-names: the name of the corresponding PHY device - syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) +- ports: Contains 2 DSI controller ports as child nodes. Each port contains + an endpoint subnode as defined in [2] and [3]. Optional properties: - panel@0: Node of panel connected to this DSI controller. - See files in Documentation/devicetree/bindings/display/panel/ for each supported - panel. + See files in [4] for each supported panel. - qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is driving a panel which needs 2 DSI links. - qcom,master-dsi: Boolean value indicating if the DSI controller is driving @@ -44,34 +48,38 @@ Optional properties: - pinctrl-names: the pin control state names; should contain "default" - pinctrl-0: the default pinctrl state (active) - pinctrl-n: the "sleep" pinctrl state -- port: DSI controller output port, containing one endpoint subnode. +- ports: contains DSI controller input and output ports as children, each + containing one endpoint subnode. DSI Endpoint properties: - - remote-endpoint: set to phandle of the connected panel's endpoint. - See Documentation/devicetree/bindings/graph.txt for device graph info. - - qcom,data-lane-map: this describes how the logical DSI lanes are mapped - to the physical lanes on the given platform. The value contained in - index n describes what logical data lane is mapped to the physical data - lane n (DATAn, where n lies between 0 and 3). + - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's + input endpoint. For port@1, set to the MDP interface output. See [2] for + device graph info. + + - data-lanes: this describes how the physical DSI data lanes are mapped + to the logical lanes on the given platform. The value contained in + index n describes what physical lane is mapped to the logical lane n + (DATAn, where n lies between 0 and 3). The clock lane position is fixed + and can't be changed. Hence, they aren't a part of the DT bindings. See + [3] for more info on the data-lanes property. For example: - qcom,data-lane-map = <3 0 1 2>; + data-lanes = <3 0 1 2>; - The above mapping describes that the logical data lane DATA3 is mapped to - the physical data lane DATA0, logical DATA0 to physical DATA1, logic DATA1 - to phys DATA2 and logic DATA2 to phys DATA3. + The above mapping describes that the logical data lane DATA0 is mapped to + the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 + to phys DATA1 and logic DATA3 to phys DATA2. There are only a limited number of physical to logical mappings possible: - - "0123": Logic 0->Phys 0; Logic 1->Phys 1; Logic 2->Phys 2; Logic 3->Phys 3; - "3012": Logic 3->Phys 0; Logic 0->Phys 1; Logic 1->Phys 2; Logic 2->Phys 3; - "2301": Logic 2->Phys 0; Logic 3->Phys 1; Logic 0->Phys 2; Logic 1->Phys 3; - "1230": Logic 1->Phys 0; Logic 2->Phys 1; Logic 3->Phys 2; Logic 0->Phys 3; - "0321": Logic 0->Phys 0; Logic 3->Phys 1; Logic 2->Phys 2; Logic 1->Phys 3; - "1032": Logic 1->Phys 0; Logic 0->Phys 1; Logic 3->Phys 2; Logic 2->Phys 3; - "2103": Logic 2->Phys 0; Logic 1->Phys 1; Logic 0->Phys 2; Logic 3->Phys 3; - "3210": Logic 3->Phys 0; Logic 2->Phys 1; Logic 1->Phys 2; Logic 0->Phys 3; + <0 1 2 3> + <1 2 3 0> + <2 3 0 1> + <3 0 1 2> + <0 3 2 1> + <1 0 3 2> + <2 1 0 3> + <3 2 1 0> DSI PHY: Required properties: @@ -86,11 +94,12 @@ Required properties: * "dsi_pll" * "dsi_phy" * "dsi_phy_regulator" +- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating + 2 clocks: A byte clock (index 0), and a pixel clock (index 1). - qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should be 0 or 1, since we have 2 DSI PHYs at most for now. - power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clocks: Phandles to device clocks. See [1] for details on clock bindings. - clock-names: the following clocks are required: * "iface_clk" - vddio-supply: phandle to vdd-io regulator device node @@ -99,11 +108,16 @@ Optional properties: - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY regulator is wanted. +[1] Documentation/devicetree/bindings/clocks/clock-bindings.txt +[2] Documentation/devicetree/bindings/graph.txt +[3] Documentation/devicetree/bindings/media/video-interfaces.txt +[4] Documentation/devicetree/bindings/display/panel/ + Example: - mdss_dsi0: qcom,mdss_dsi@fd922800 { + dsi0: dsi@fd922800 { compatible = "qcom,mdss-dsi-ctrl"; qcom,dsi-host-index = <0>; - interrupt-parent = <&mdss_mdp>; + interrupt-parent = <&mdp>; interrupts = <4 0>; reg-names = "dsi_ctrl"; reg = <0xfd922800 0x200>; @@ -124,19 +138,48 @@ Example: <&mmcc MDSS_AHB_CLK>, <&mmcc MDSS_MDP_CLK>, <&mmcc MDSS_PCLK0_CLK>; + + assigned-clocks = + <&mmcc BYTE0_CLK_SRC>, + <&mmcc PCLK0_CLK_SRC>; + assigned-clock-parents = + <&dsi_phy0 0>, + <&dsi_phy0 1>; + vdda-supply = <&pma8084_l2>; vdd-supply = <&pma8084_l22>; vddio-supply = <&pma8084_l12>; - qcom,dsi-phy = <&mdss_dsi_phy0>; + phys = <&dsi_phy0>; + phy-names ="dsi-phy"; qcom,dual-dsi-mode; qcom,master-dsi; qcom,sync-dual-dsi; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&mdss_dsi_active>; - pinctrl-1 = <&mdss_dsi_suspend>; + pinctrl-0 = <&dsi_active>; + pinctrl-1 = <&dsi_suspend>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; panel: panel@0 { compatible = "sharp,lq101r1sx01"; @@ -152,16 +195,9 @@ Example: }; }; }; - - port { - dsi0_out: endpoint { - remote-endpoint = <&panel_in>; - lanes = <0 1 2 3>; - }; - }; }; - mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 { + dsi_phy0: dsi-phy@fd922a00 { compatible = "qcom,dsi-phy-28nm-hpm"; qcom,dsi-phy-index = <0>; reg-names = @@ -173,6 +209,7 @@ Example: <0xfd922d80 0x7b>; clock-names = "iface_clk"; clocks = <&mmcc MDSS_AHB_CLK>; + #clock-cells = <1>; vddio-supply = <&pma8084_l12>; qcom,dsi-phy-regulator-ldo-mode; diff --git a/Bindings/display/msm/hdmi.txt b/Bindings/display/msm/hdmi.txt index b63f614e0c04..2ad578984fcf 100644 --- a/Bindings/display/msm/hdmi.txt +++ b/Bindings/display/msm/hdmi.txt @@ -14,17 +14,16 @@ Required properties: - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: device clocks See ../clocks/clock-bindings.txt for details. -- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin -- qcom,hdmi-tx-ddc-data-gpio: ddc data pin -- qcom,hdmi-tx-hpd-gpio: hpd pin - core-vdda-supply: phandle to supply regulator - hdmi-mux-supply: phandle to mux regulator - phys: the phandle for the HDMI PHY device - phy-names: the name of the corresponding PHY device Optional properties: -- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin -- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin +- hpd-gpios: hpd pin +- qcom,hdmi-tx-mux-en-gpios: hdmi mux enable pin +- qcom,hdmi-tx-mux-sel-gpios: hdmi mux select pin +- qcom,hdmi-tx-mux-lpm-gpios: hdmi mux lpm pin - power-domains: reference to the power domain(s), if available. - pinctrl-names: the pin control state names; should contain "default" - pinctrl-0: the default pinctrl state (active) diff --git a/Bindings/display/msm/mdp4.txt b/Bindings/display/msm/mdp4.txt new file mode 100644 index 000000000000..3c341a15ccdc --- /dev/null +++ b/Bindings/display/msm/mdp4.txt @@ -0,0 +1,112 @@ +Qualcomm adreno/snapdragon MDP4 display controller + +Description: + +This is the bindings documentation for the MDP4 display controller found in +SoCs like MSM8960, APQ8064 and MSM8660. + +Required properties: +- compatible: + * "qcom,mdp4" - mdp4 +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the display controller. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "core_clk" + * "iface_clk" + * "bus_clk" + * "lut_clk" + * "hdmi_clk" + * "tv_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The output port mappings are: + Port 0 -> LCDC/LVDS + Port 1 -> DSI1 Cmd/Video + Port 2 -> DSI2 Cmd/Video + Port 3 -> DTV + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + hdmi: hdmi@4a00000 { + ... + ports { + ... + port@0 { + reg = <0>; + hdmi_in: endpoint { + remote-endpoint = <&mdp_dtv_out>; + }; + }; + ... + }; + ... + }; + + ... + + mdp: mdp@5100000 { + compatible = "qcom,mdp4"; + reg = <0x05100000 0xf0000>; + interrupts = <GIC_SPI 75 0>; + clock-names = + "core_clk", + "iface_clk", + "lut_clk", + "hdmi_clk", + "tv_clk"; + clocks = + <&mmcc MDP_CLK>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_AXI_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp_lvds_out: endpoint { + }; + }; + + port@1 { + reg = <1>; + mdp_dsi1_out: endpoint { + }; + }; + + port@2 { + reg = <2>; + mdp_dsi2_out: endpoint { + }; + }; + + port@3 { + reg = <3>; + mdp_dtv_out: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; +}; diff --git a/Bindings/display/msm/mdp5.txt b/Bindings/display/msm/mdp5.txt new file mode 100644 index 000000000000..30c11ea83754 --- /dev/null +++ b/Bindings/display/msm/mdp5.txt @@ -0,0 +1,160 @@ +Qualcomm adreno/snapdragon MDP5 display controller + +Description: + +This is the bindings documentation for the Mobile Display Subsytem(MDSS) that +encapsulates sub-blocks like MDP5, DSI, HDMI, eDP etc, and the MDP5 display +controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994 and MSM8996. + +MDSS: +Required properties: +- compatible: + * "qcom,mdss" - MDSS +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdss_phys" + * "vbif_phys" +- interrupts: The interrupt signal from MDSS. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "iface_clk" + * "bus_clk" + * "vsync_clk" +- #address-cells: number of address cells for the MDSS children. Should be 1. +- #size-cells: Should be 1. +- ranges: parent bus address space is the same as the child bus address space. + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +MDP5: +Required properties: +- compatible: + * "qcom,mdp5" - MDP5 +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdp_phys" +- interrupts: Interrupt line from MDP5 to MDSS interrupt controller. +- interrupt-parent: phandle to the MDSS block + through MDP block +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. +- * "bus_clk" +- * "iface_clk" +- * "core_clk" +- * "vsync_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The availability of output ports can vary across SoC revisions: + + For MSM8974 and APQ8084: + Port 0 -> MDP_INTF0 (eDP) + Port 1 -> MDP_INTF1 (DSI1) + Port 2 -> MDP_INTF2 (DSI2) + Port 3 -> MDP_INTF3 (HDMI) + + For MSM8916: + Port 0 -> MDP_INTF1 (DSI1) + + For MSM8994 and MSM8996: + Port 0 -> MDP_INTF1 (DSI1) + Port 1 -> MDP_INTF2 (DSI2) + Port 2 -> MDP_INTF3 (HDMI) + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + mdss: mdss@1a00000 { + compatible = "qcom,mdss"; + reg = <0x1a00000 0x1000>, + <0x1ac8000 0x3000>; + reg-names = "mdss_phys", "vbif_phys"; + + power-domains = <&gcc MDSS_GDSC>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "vsync_clk" + + interrupts = <0 72 0>; + + interrupt-controller; + #interrupt-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mdp: mdp@1a01000 { + compatible = "qcom,mdp5"; + reg = <0x1a01000 0x90000>; + reg-names = "mdp_phys"; + + interrupt-parent = <&mdss>; + interrupts = <0 0>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "core_clk", + "vsync_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp5_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi0: dsi@1a98000 { + ... + ports { + ... + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp5_intf1_out>; + }; + }; + ... + }; + ... + }; + + dsi_phy0: dsi-phy@1a98300 { + ... + }; + }; +}; diff --git a/Bindings/display/mxsfb.txt b/Bindings/display/mxsfb.txt index 96ec5179c8a0..472e1ea6c591 100644 --- a/Bindings/display/mxsfb.txt +++ b/Bindings/display/mxsfb.txt @@ -1,20 +1,57 @@ * Freescale MXS LCD Interface (LCDIF) +New bindings: +============= Required properties: -- compatible: Should be "fsl,<chip>-lcdif". Supported chips include - imx23 and imx28. -- reg: Address and length of the register set for lcdif -- interrupts: Should contain lcdif interrupts -- display : phandle to display node (see below for details) +- compatible: Should be "fsl,imx23-lcdif" for i.MX23. + Should be "fsl,imx28-lcdif" for i.MX28. + Should be "fsl,imx6sx-lcdif" for i.MX6SX. +- reg: Address and length of the register set for LCDIF +- interrupts: Should contain LCDIF interrupt +- clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. +- clock-names: A list of clock names. For MXSFB it should contain: + - "pix" for the LCDIF block clock + - (MX6SX-only) "axi", "disp_axi" for the bus interface clock + +Required sub-nodes: + - port: The connection to an encoder chip. + +Example: + + lcdif1: display-controller@2220000 { + compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif"; + reg = <0x02220000 0x4000>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>, + <&clks IMX6SX_CLK_LCDIF_APB>, + <&clks IMX6SX_CLK_DISPLAY_AXI>; + clock-names = "pix", "axi", "disp_axi"; + + port { + parallel_out: endpoint { + remote-endpoint = <&panel_in_parallel>; + }; + }; + }; + +Deprecated bindings: +==================== +Required properties: +- compatible: Should be "fsl,imx23-lcdif" for i.MX23. + Should be "fsl,imx28-lcdif" for i.MX28. +- reg: Address and length of the register set for LCDIF +- interrupts: Should contain LCDIF interrupts +- display: phandle to display node (see below for details) * display node Required properties: -- bits-per-pixel : <16> for RGB565, <32> for RGB888/666. -- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>. +- bits-per-pixel: <16> for RGB565, <32> for RGB888/666. +- bus-width: number of data lines. Could be <8>, <16>, <18> or <24>. Required sub-node: -- display-timings : Refer to binding doc display-timing.txt for details. +- display-timings: Refer to binding doc display-timing.txt for details. Examples: diff --git a/Bindings/display/panel/auo,g133han01.txt b/Bindings/display/panel/auo,g133han01.txt new file mode 100644 index 000000000000..3afc76747824 --- /dev/null +++ b/Bindings/display/panel/auo,g133han01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 13.3" FHD (1920x1080) TFT LCD panel + +Required properties: +- compatible: should be "auo,g133han01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/auo,g185han01.txt b/Bindings/display/panel/auo,g185han01.txt new file mode 100644 index 000000000000..ed657c2141d4 --- /dev/null +++ b/Bindings/display/panel/auo,g185han01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 18.5" FHD (1920x1080) TFT LCD panel + +Required properties: +- compatible: should be "auo,g185han01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/auo,t215hvn01.txt b/Bindings/display/panel/auo,t215hvn01.txt new file mode 100644 index 000000000000..cbd9da3f03b1 --- /dev/null +++ b/Bindings/display/panel/auo,t215hvn01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 21.5" FHD (1920x1080) color TFT LCD panel + +Required properties: +- compatible: should be "auo,t215hvn01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/chunghwa,claa070wp03xg.txt b/Bindings/display/panel/chunghwa,claa070wp03xg.txt new file mode 100644 index 000000000000..dd22685d2adc --- /dev/null +++ b/Bindings/display/panel/chunghwa,claa070wp03xg.txt @@ -0,0 +1,7 @@ +Chunghwa Picture Tubes Ltd. 7" WXGA TFT LCD panel + +Required properties: +- compatible: should be "chunghwa,claa070wp03xg" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/display-timing.txt b/Bindings/display/panel/display-timing.txt index e1d4a0b59612..81a75893d1b8 100644 --- a/Bindings/display/panel/display-timing.txt +++ b/Bindings/display/panel/display-timing.txt @@ -32,6 +32,14 @@ optional properties: - active low = drive pixel data on falling edge/ sample data on rising edge - ignored = ignored + - syncclk-active: with + - active high = drive sync on rising edge/ + sample sync on falling edge of pixel + clock + - active low = drive sync on falling edge/ + sample sync on rising edge of pixel + clock + - omitted = same configuration as pixelclk-active - interlaced (bool): boolean to enable interlaced mode - doublescan (bool): boolean to enable doublescan mode - doubleclk (bool): boolean to enable doubleclock mode diff --git a/Bindings/display/panel/innolux,g101ice-l01.txt b/Bindings/display/panel/innolux,g101ice-l01.txt new file mode 100644 index 000000000000..9e7590465227 --- /dev/null +++ b/Bindings/display/panel/innolux,g101ice-l01.txt @@ -0,0 +1,7 @@ +Innolux Corporation 10.1" G101ICE-L01 WXGA (1280x800) LVDS panel + +Required properties: +- compatible: should be "innolux,g101ice-l01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/jdi,lt070me05000.txt b/Bindings/display/panel/jdi,lt070me05000.txt new file mode 100644 index 000000000000..4989c91d505f --- /dev/null +++ b/Bindings/display/panel/jdi,lt070me05000.txt @@ -0,0 +1,31 @@ +JDI model LT070ME05000 1200x1920 7" DSI Panel + +Required properties: +- compatible: should be "jdi,lt070me05000" +- vddp-supply: phandle of the regulator that provides the supply voltage + Power IC supply (3-5V) +- iovcc-supply: phandle of the regulator that provides the supply voltage + IOVCC , power supply for LCM (1.8V) +- enable-gpios: phandle of gpio for enable line + LED_EN, LED backlight enable, High active +- reset-gpios: phandle of gpio for reset line + This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names + XRES, Reset, Low active +- dcdc-en-gpios: phandle of the gpio for power ic line + Power IC supply enable, High active + +Example: + + dsi0: qcom,mdss_dsi@4700000 { + panel@0 { + compatible = "jdi,lt070me05000"; + reg = <0>; + + vddp-supply = <&pm8921_l17>; + iovcc-supply = <&pm8921_lvs7>; + + enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>; + reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>; + dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Bindings/display/panel/lg,lp079qx1-sp0v.txt b/Bindings/display/panel/lg,lp079qx1-sp0v.txt new file mode 100644 index 000000000000..b9877acad012 --- /dev/null +++ b/Bindings/display/panel/lg,lp079qx1-sp0v.txt @@ -0,0 +1,7 @@ +LG LP079QX1-SP0V 7.9" (1536x2048 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp079qx1-sp0v" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/lg,lp097qx1-spa1.txt b/Bindings/display/panel/lg,lp097qx1-spa1.txt new file mode 100644 index 000000000000..42141516f078 --- /dev/null +++ b/Bindings/display/panel/lg,lp097qx1-spa1.txt @@ -0,0 +1,7 @@ +LG 9.7" (2048x1536 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp097qx1-spa1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/nvd,9128.txt b/Bindings/display/panel/nvd,9128.txt new file mode 100644 index 000000000000..17bcd017c678 --- /dev/null +++ b/Bindings/display/panel/nvd,9128.txt @@ -0,0 +1,7 @@ +New Vision Display 7.0" 800 RGB x 480 TFT LCD panel + +Required properties: +- compatible: should be "nvd,9128" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/panel-dpi.txt b/Bindings/display/panel/panel-dpi.txt index 216c894d4f99..b52ac52757df 100644 --- a/Bindings/display/panel/panel-dpi.txt +++ b/Bindings/display/panel/panel-dpi.txt @@ -7,6 +7,8 @@ Required properties: Optional properties: - label: a symbolic name for the panel - enable-gpios: panel enable gpio +- reset-gpios: GPIO to control the RESET pin +- vcc-supply: phandle of regulator that will be used to enable power to the display Required nodes: - "panel-timing" containing video timings diff --git a/Bindings/display/panel/samsung,lsn122dl01-c01.txt b/Bindings/display/panel/samsung,lsn122dl01-c01.txt new file mode 100644 index 000000000000..dba298b43b24 --- /dev/null +++ b/Bindings/display/panel/samsung,lsn122dl01-c01.txt @@ -0,0 +1,7 @@ +Samsung 12.2" (2560x1600 pixels) TFT LCD panel + +Required properties: +- compatible: should be "samsung,lsn122dl01-c01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/sharp,lq101k1ly04.txt b/Bindings/display/panel/sharp,lq101k1ly04.txt new file mode 100644 index 000000000000..4aff25b8dfe6 --- /dev/null +++ b/Bindings/display/panel/sharp,lq101k1ly04.txt @@ -0,0 +1,7 @@ +Sharp Display Corp. LQ101K1LY04 10.07" WXGA TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq101k1ly04" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/sharp,lq123p1jx31.txt b/Bindings/display/panel/sharp,lq123p1jx31.txt new file mode 100644 index 000000000000..bcb0e8a29f71 --- /dev/null +++ b/Bindings/display/panel/sharp,lq123p1jx31.txt @@ -0,0 +1,7 @@ +Sharp 12.3" (2400x1600 pixels) TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq123p1jx31" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/sharp,lq150x1lg11.txt b/Bindings/display/panel/sharp,lq150x1lg11.txt new file mode 100644 index 000000000000..0f57c3143506 --- /dev/null +++ b/Bindings/display/panel/sharp,lq150x1lg11.txt @@ -0,0 +1,36 @@ +Sharp 15" LQ150X1LG11 XGA TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq150x1lg11" +- power-supply: regulator to provide the VCC supply voltage (3.3 volts) + +Optional properties: +- backlight: phandle of the backlight device +- rlud-gpios: a single GPIO for the RL/UD (rotate 180 degrees) pin. +- sellvds-gpios: a single GPIO for the SELLVDS pin. + +If rlud-gpios and/or sellvds-gpios are not specified, the RL/UD and/or SELLVDS +pins are assumed to be handled appropriately by the hardware. + +Example: + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 100000>; /* VBR */ + + brightness-levels = <0 20 40 60 80 100>; + default-brightness-level = <2>; + + power-supply = <&vdd_12v_reg>; /* VDD */ + enable-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; /* XSTABY */ + }; + + panel { + compatible = "sharp,lq150x1lg11"; + + power-supply = <&vcc_3v3_reg>; /* VCC */ + + backlight = <&backlight>; + rlud-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; /* RL/UD */ + sellvds-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; /* SELLVDS */ + }; diff --git a/Bindings/display/panel/starry,kr122ea0sra.txt b/Bindings/display/panel/starry,kr122ea0sra.txt new file mode 100644 index 000000000000..1e87fe6078af --- /dev/null +++ b/Bindings/display/panel/starry,kr122ea0sra.txt @@ -0,0 +1,7 @@ +Starry 12.2" (1920x1200 pixels) TFT LCD panel + +Required properties: +- compatible: should be "starry,kr122ea0sra" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Bindings/display/panel/tpo,tpg110.txt b/Bindings/display/panel/tpo,tpg110.txt new file mode 100644 index 000000000000..f5e3c6f2095a --- /dev/null +++ b/Bindings/display/panel/tpo,tpg110.txt @@ -0,0 +1,47 @@ +TPO TPG110 Panel +================ + +This binding builds on the DPI bindings, adding a few properties +as a superset of a DPI. See panel-dpi.txt for the required DPI +bindings. + +Required properties: +- compatible : "tpo,tpg110" +- grestb-gpios : panel reset GPIO +- scen-gpios : serial control enable GPIO +- scl-gpios : serial control clock line GPIO +- sda-gpios : serial control data line GPIO + +Required nodes: +- Video port for DPI input, see panel-dpi.txt +- Panel timing for DPI setup, see panel-dpi.txt + +Example +------- + +panel { + compatible = "tpo,tpg110", "panel-dpi"; + grestb-gpios = <&stmpe_gpio44 5 GPIO_ACTIVE_LOW>; + scen-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + scl-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + backlight = <&bl>; + + port { + nomadik_clcd_panel: endpoint { + remote-endpoint = <&nomadik_clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <33200000>; + hactive = <800>; + hback-porch = <216>; + hfront-porch = <40>; + hsync-len = <1>; + vactive = <480>; + vback-porch = <35>; + vfront-porch = <10>; + vsync-len = <1>; + }; +}; diff --git a/Bindings/display/renesas,du.txt b/Bindings/display/renesas,du.txt index 0d30e42e40be..1a02f099a0ff 100644 --- a/Bindings/display/renesas,du.txt +++ b/Bindings/display/renesas,du.txt @@ -6,9 +6,11 @@ Required Properties: - "renesas,du-r8a7779" for R8A7779 (R-Car H1) compatible DU - "renesas,du-r8a7790" for R8A7790 (R-Car H2) compatible DU - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU + - "renesas,du-r8a7792" for R8A7792 (R-Car V2H) compatible DU - "renesas,du-r8a7793" for R8A7793 (R-Car M2-N) compatible DU - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU + - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU - reg: A list of base address and length of each memory resource, one for each entry in the reg-names property. @@ -25,10 +27,10 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - R8A779[01345] use one functional clock per channel and one clock per LVDS - encoder (if available). The functional clocks must be named "du.x" with - "x" being the channel numerical index. The LVDS clocks must be named - "lvds.x" with "x" being the LVDS encoder numerical index. + - R8A779[0123456] use one functional clock per channel and one clock per + LVDS encoder (if available). The functional clocks must be named "du.x" + with "x" being the channel numerical index. The LVDS clocks must be + named "lvds.x" with "x" being the LVDS encoder numerical index. - In addition to the functional and encoder clocks, all DU versions also support externally supplied pixel clocks. Those clocks are optional. When supplied they must be named "dclkin.x" with "x" being the input @@ -47,9 +49,11 @@ corresponding to each DU output. R8A7779 (H1) DPAD 0 DPAD 1 - - R8A7790 (H2) DPAD LVDS 0 LVDS 1 - R8A7791 (M2-W) DPAD LVDS 0 - - + R8A7792 (V2H) DPAD 0 DPAD 1 - - R8A7793 (M2-N) DPAD LVDS 0 - - R8A7794 (E2) DPAD 0 DPAD 1 - - R8A7795 (H3) DPAD HDMI 0 HDMI 1 LVDS + R8A7796 (M3-W) DPAD HDMI LVDS - Example: R8A7790 (R-Car H2) DU diff --git a/Bindings/display/rockchip/analogix_dp-rockchip.txt b/Bindings/display/rockchip/analogix_dp-rockchip.txt index e832ff98fd61..01cced1c2a18 100644 --- a/Bindings/display/rockchip/analogix_dp-rockchip.txt +++ b/Bindings/display/rockchip/analogix_dp-rockchip.txt @@ -2,7 +2,8 @@ Rockchip RK3288 specific extensions to the Analogix Display Port ================================ Required properties: -- compatible: "rockchip,rk3288-edp"; +- compatible: "rockchip,rk3288-dp", + "rockchip,rk3399-edp"; - reg: physical base address of the controller and length @@ -27,6 +28,12 @@ Required properties: Port 0: contained 2 endpoints, connecting to the output of vop. Port 1: contained 1 endpoint, connecting to the input of panel. +Optional property for different chips: +- clocks: from common clock binding: handle to grf_vio clock. + +- clock-names: from common clock binding: + Required elements: "grf" + For the below properties, please refer to Analogix DP binding document: * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt - phys (required) diff --git a/Bindings/display/rockchip/rockchip-vop.txt b/Bindings/display/rockchip/rockchip-vop.txt index 5489b59e3d41..9eb3f0a2a078 100644 --- a/Bindings/display/rockchip/rockchip-vop.txt +++ b/Bindings/display/rockchip/rockchip-vop.txt @@ -6,8 +6,10 @@ buffer to an external LCD interface. Required properties: - compatible: value should be one of the following - "rockchip,rk3288-vop"; "rockchip,rk3036-vop"; + "rockchip,rk3288-vop"; + "rockchip,rk3399-vop-big"; + "rockchip,rk3399-vop-lit"; - interrupts: should contain a list of all VOP IP block interrupts in the order: VSYNC, LCD_SYSTEM. The interrupt specifier diff --git a/Bindings/display/sunxi/sun4i-drm.txt b/Bindings/display/sunxi/sun4i-drm.txt index df8f4aeefe4c..b82c00449468 100644 --- a/Bindings/display/sunxi/sun4i-drm.txt +++ b/Bindings/display/sunxi/sun4i-drm.txt @@ -26,13 +26,16 @@ TCON The TCON acts as a timing controller for RGB, LVDS and TV interfaces. Required properties: - - compatible: value should be "allwinner,sun5i-a13-tcon". + - compatible: value must be either: + * allwinner,sun5i-a13-tcon + * allwinner,sun6i-a31-tcon + * allwinner,sun6i-a31s-tcon + * allwinner,sun8i-a33-tcon - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the TCON. Three are needed: - 'ahb': the interface clocks - 'tcon-ch0': The clock driving the TCON channel 0 - - 'tcon-ch1': The clock driving the TCON channel 1 - resets: phandles to the reset controllers driving the encoder - "lcd": the reset line for the TCON channel 0 @@ -49,6 +52,35 @@ Required properties: second the block connected to the TCON channel 1 (usually the TV encoder) +On SoCs other than the A33, there is one more clock required: + - 'tcon-ch1': The clock driving the TCON channel 1 + +DRC +--- + +The DRC (Dynamic Range Controller), found in the latest Allwinner SoCs +(A31, A23, A33), allows to dynamically adjust pixel +brightness/contrast based on histogram measurements for LCD content +adaptive backlight control. + + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-drc + * allwinner,sun6i-a31s-drc + * allwinner,sun8i-a33-drc + - reg: base address and size of the memory-mapped region. + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the DRC + * ahb: the DRC interface clock + * mod: the DRC module clock + * ram: the DRC DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset line driving the DRC + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the outputs Display Engine Backend ---------------------- @@ -59,6 +91,8 @@ system. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-backend + * allwinner,sun6i-a31-display-backend + * allwinner,sun8i-a33-display-backend - reg: base address and size of the memory-mapped region. - clocks: phandles to the clocks feeding the frontend and backend * ahb: the backend interface clock @@ -71,6 +105,14 @@ Required properties: Documentation/devicetree/bindings/media/video-interfaces.txt. The first port should be the input endpoints, the second one the output +On the A33, some additional properties are required: + - reg needs to have an additional region corresponding to the SAT + - reg-names need to be set, with "be" and "sat" + - clocks and clock-names need to have a phandle to the SAT bus + clocks, whose name will be "sat" + - resets and reset-names need to have a phandle to the SAT bus + resets, whose name will be "sat" + Display Engine Frontend ----------------------- @@ -80,6 +122,8 @@ deinterlacing and color space conversion. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-frontend + * allwinner,sun6i-a31-display-frontend + * allwinner,sun8i-a33-display-frontend - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the frontend and backend @@ -104,6 +148,9 @@ extra node. Required properties: - compatible: value must be one of: * allwinner,sun5i-a13-display-engine + * allwinner,sun6i-a31-display-engine + * allwinner,sun6i-a31s-display-engine + * allwinner,sun8i-a33-display-engine - allwinner,pipelines: list of phandle to the display engine frontends available. diff --git a/Bindings/display/tegra/nvidia,tegra20-host1x.txt b/Bindings/display/tegra/nvidia,tegra20-host1x.txt index a3bd8c050c4e..0fad7ed2ea19 100644 --- a/Bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -208,6 +208,7 @@ of the following host1x client modules: See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - sor: clock input for the SOR hardware + - source: source clock for the SOR clock - parent: input for the pixel clock - dp: reference clock for the SOR clock - safe: safe reference for the SOR clock during power up @@ -226,9 +227,9 @@ of the following host1x client modules: - nvidia,dpaux: phandle to a DispayPort AUX interface - dpaux: DisplayPort AUX interface - - compatible: For Tegra124, must contain "nvidia,tegra124-dpaux". Otherwise, - must contain '"nvidia,<chip>-dpaux", "nvidia,tegra124-dpaux"', where - <chip> is tegra132. + - compatible : Should contain one of the following: + - "nvidia,tegra124-dpaux": for Tegra124 and Tegra132 + - "nvidia,tegra210-dpaux": for Tegra210 - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. - clocks: Must contain an entry for each entry in clock-names. @@ -241,6 +242,12 @@ of the following host1x client modules: - reset-names: Must include the following entries: - dpaux - vdd-supply: phandle of a supply that powers the DisplayPort link + - i2c-bus: Subnode where I2C slave devices are listed. This subnode + must be always present. If there are no I2C slave devices, an empty + node should be added. See ../../i2c/i2c.txt for more information. + + See ../pinctrl/nvidia,tegra124-dpaux-padctl.txt for information + regarding the DPAUX pad controller bindings. Example: diff --git a/Bindings/display/tilcdc/tilcdc.txt b/Bindings/display/tilcdc/tilcdc.txt index 2136ee81e061..6fddb4f4f71a 100644 --- a/Bindings/display/tilcdc/tilcdc.txt +++ b/Bindings/display/tilcdc/tilcdc.txt @@ -1,7 +1,9 @@ Device-Tree bindings for tilcdc DRM driver Required properties: - - compatible: value should be "ti,am33xx-tilcdc". + - compatible: value should be one of the following: + - "ti,am33xx-tilcdc" for AM335x based boards + - "ti,da850-tilcdc" for DA850/AM18x/OMAP-L138 based boards - interrupts: the interrupt number - reg: base address and size of the LCDC device @@ -17,6 +19,18 @@ Optional properties: the lcd controller. - max-pixelclock: The maximum pixel clock that can be supported by the lcd controller in KHz. + - blue-and-red-wiring: Recognized values "straight" or "crossed". + This property deals with the LCDC revision 2 (found on AM335x) + color errata [1]. + - "straight" indicates normal wiring that supports RGB565, + BGR888, and XBGR8888 color formats. + - "crossed" indicates wiring that has blue and red wires + crossed. This setup supports BGR565, RGB888 and XRGB8888 + formats. + - If the property is not present or its value is not recognized + the legacy mode is assumed. This configuration supports RGB565, + RGB888 and XRGB8888 formats. However, depending on wiring, the red + and blue colors are swapped in either 16 or 24-bit color modes. Optional nodes: @@ -24,15 +38,29 @@ Optional nodes: binding follows Documentation/devicetree/bindings/graph.txt and suppors a single port with a single endpoint. + - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and + Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting + tfp410 DVI encoder or lcd panel to lcdc + +[1] There is an errata about AM335x color wiring. For 16-bit color mode + the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]), + but for 24 bit color modes the wiring of blue and red components is + crossed and LCD_DATA[0:4] is for Red[3:7] and LCD_DATA[11:15] is + for Blue[3-7]. For more details see section 3.1.1 in AM335x + Silicon Errata: + http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360 + Example: fb: fb@4830e000 { - compatible = "ti,am33xx-tilcdc"; + compatible = "ti,am33xx-tilcdc", "ti,da850-tilcdc"; reg = <0x4830e000 0x1000>; interrupt-parent = <&intc>; interrupts = <36>; ti,hwmods = "lcdc"; + blue-and-red-wiring = "crossed"; + port { lcdc_0: endpoint@0 { remote-endpoint = <&hdmi_0>; diff --git a/Bindings/display/zte,vou.txt b/Bindings/display/zte,vou.txt new file mode 100644 index 000000000000..740e5bd2e4f7 --- /dev/null +++ b/Bindings/display/zte,vou.txt @@ -0,0 +1,84 @@ +ZTE VOU Display Controller + +This is a display controller found on ZTE ZX296718 SoC. It includes multiple +Graphic Layer (GL) and Video Layer (VL), two Mixers/Channels, and a few blocks +handling scaling, color space conversion etc. VOU also integrates the support +for typical output devices, like HDMI, TV Encoder, VGA, and RGB LCD. + +* Master VOU node + +It must be the parent node of all the sub-device nodes. + +Required properties: + - compatible: should be "zte,zx296718-vou" + - #address-cells: should be <1> + - #size-cells: should be <1> + - ranges: list of address translations between VOU and sub-devices + +* VOU DPC device + +Required properties: + - compatible: should be "zte,zx296718-dpc" + - reg: Physical base address and length of DPC register regions, one for each + entry in 'reg-names' + - reg-names: The names of register regions. The following regions are required: + "osd" + "timing_ctrl" + "dtrc" + "vou_ctrl" + "otfppu" + - interrupts: VOU DPC interrupt number to CPU + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. The following clocks are required: + "aclk" + "ppu_wclk" + "main_wclk" + "aux_wclk" + +* HDMI output device + +Required properties: + - compatible: should be "zte,zx296718-hdmi" + - reg: Physical base address and length of the HDMI device IO region + - interrupts : HDMI interrupt number to CPU + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. The following clocks are required: + "osc_cec" + "osc_clk" + "xclk" + +Example: + +vou: vou@1440000 { + compatible = "zte,zx296718-vou"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1440000 0x10000>; + + dpc: dpc@0 { + compatible = "zte,zx296718-dpc"; + reg = <0x0000 0x1000>, <0x1000 0x1000>, + <0x5000 0x1000>, <0x6000 0x1000>, + <0xa000 0x1000>; + reg-names = "osd", "timing_ctrl", + "dtrc", "vou_ctrl", + "otfppu"; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topcrm VOU_ACLK>, <&topcrm VOU_PPU_WCLK>, + <&topcrm VOU_MAIN_WCLK>, <&topcrm VOU_AUX_WCLK>; + clock-names = "aclk", "ppu_wclk", + "main_wclk", "aux_wclk"; + }; + + hdmi: hdmi@c000 { + compatible = "zte,zx296718-hdmi"; + reg = <0xc000 0x4000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>; + clocks = <&topcrm HDMI_OSC_CEC>, + <&topcrm HDMI_OSC_CLK>, + <&topcrm HDMI_XCLK>; + clock-names = "osc_cec", "osc_clk", "xclk"; + }; +}; |