diff options
Diffstat (limited to 'Bindings/extcon/extcon-arizona.txt')
| -rw-r--r-- | Bindings/extcon/extcon-arizona.txt | 75 |
1 files changed, 75 insertions, 0 deletions
diff --git a/Bindings/extcon/extcon-arizona.txt b/Bindings/extcon/extcon-arizona.txt new file mode 100644 index 000000000000..e27341f8a4c7 --- /dev/null +++ b/Bindings/extcon/extcon-arizona.txt @@ -0,0 +1,75 @@ +Cirrus Logic Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilities and a range +of analogue I/O. + +This document lists Extcon specific bindings, see the primary binding document: + ../mfd/arizona.txt + +Optional properties: + + - wlf,hpdet-channel : Headphone detection channel. + ARIZONA_ACCDET_MODE_HPL or 1 - Headphone detect mode is set to HPDETL + ARIZONA_ACCDET_MODE_HPR or 2 - Headphone detect mode is set to HPDETR + If this node is not mentioned or if the value is unknown, then + headphone detection mode is set to HPDETL. + + - wlf,use-jd2 : Use the additional JD input along with JD1 for dual pin jack + detection. + - wlf,use-jd2-nopull : Internal pull on JD2 is disabled when used for + jack detection. + - wlf,jd-invert : Invert the polarity of the jack detection switch + + - wlf,micd-software-compare : Use a software comparison to determine mic + presence + - wlf,micd-detect-debounce : Additional software microphone detection + debounce specified in milliseconds. + - wlf,micd-pol-gpio : GPIO specifier for the GPIO controlling the headset + polarity if one exists. + - wlf,micd-bias-start-time : Time allowed for MICBIAS to startup prior to + performing microphone detection, specified as per the ARIZONA_MICD_TIME_XXX + defines. + - wlf,micd-rate : Delay between successive microphone detection measurements, + specified as per the ARIZONA_MICD_TIME_XXX defines. + - wlf,micd-dbtime : Microphone detection hardware debounces specified as the + number of measurements to take, valid values being 2 and 4. + - wlf,micd-timeout-ms : Timeout for microphone detection, specified in + milliseconds. + - wlf,micd-force-micbias : Force MICBIAS continuously on during microphone + detection. + - wlf,micd-configs : Headset polarity configurations (generally used for + detection of CTIA / OMTP headsets), the field can be of variable length + but should always be a multiple of 3 cells long, each three cell group + represents one polarity configuration. + The first cell defines the accessory detection pin, zero will use MICDET1 + and all other values will use MICDET2. + The second cell represents the MICBIAS to be used. + The third cell represents the value of the micd-pol-gpio pin. + + - wlf,gpsw : Settings for the general purpose switch + +Example: + +codec: wm8280@0 { + compatible = "wlf,wm8280"; + reg = <0>; + ... + + wlf,use-jd2; + wlf,use-jd2-nopull; + wlf,jd-invert; + + wlf,micd-software-compare; + wlf,micd-detect-debounce = <0>; + wlf,micd-pol-gpio = <&codec 2 0>; + wlf,micd-rate = <ARIZONA_MICD_TIME_8MS>; + wlf,micd-dbtime = <4>; + wlf,micd-timeout-ms = <100>; + wlf,micd-force-micbias; + wlf,micd-configs = < + 0 1 0 /* MICDET1 MICBIAS1 GPIO=low */ + 1 2 1 /* MICDET2 MICBIAS2 GPIO=high */ + >; + + wlf,gpsw = <0>; +}; |