aboutsummaryrefslogtreecommitdiff
path: root/Bindings/gpio/gpio-eic-sprd.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Bindings/gpio/gpio-eic-sprd.txt')
-rw-r--r--Bindings/gpio/gpio-eic-sprd.txt97
1 files changed, 97 insertions, 0 deletions
diff --git a/Bindings/gpio/gpio-eic-sprd.txt b/Bindings/gpio/gpio-eic-sprd.txt
new file mode 100644
index 000000000000..93d98d09d92b
--- /dev/null
+++ b/Bindings/gpio/gpio-eic-sprd.txt
@@ -0,0 +1,97 @@
+Spreadtrum EIC controller bindings
+
+The EIC is the abbreviation of external interrupt controller, which can
+be used only in input mode. The Spreadtrum platform has 2 EIC controllers,
+one is in digital chip, and another one is in PMIC. The digital chip EIC
+controller contains 4 sub-modules: EIC-debounce, EIC-latch, EIC-async and
+EIC-sync. But the PMIC EIC controller contains only one EIC-debounce sub-
+module.
+
+The EIC-debounce sub-module provides up to 8 source input signal
+connections. A debounce mechanism is used to capture the input signals'
+stable status (millisecond resolution) and a single-trigger mechanism
+is introduced into this sub-module to enhance the input event detection
+reliability. In addition, this sub-module's clock can be shut off
+automatically to reduce power dissipation. Moreover the debounce range
+is from 1ms to 4s with a step size of 1ms. The input signal will be
+ignored if it is asserted for less than 1 ms.
+
+The EIC-latch sub-module is used to latch some special power down signals
+and generate interrupts, since the EIC-latch does not depend on the APB
+clock to capture signals.
+
+The EIC-async sub-module uses a 32kHz clock to capture the short signals
+(microsecond resolution) to generate interrupts by level or edge trigger.
+
+The EIC-sync is similar with GPIO's input function, which is a synchronized
+signal input register. It can generate interrupts by level or edge trigger
+when detecting input signals.
+
+Required properties:
+- compatible: Should be one of the following:
+ "sprd,sc9860-eic-debounce",
+ "sprd,sc9860-eic-latch",
+ "sprd,sc9860-eic-async",
+ "sprd,sc9860-eic-sync",
+ "sprd,sc27xx-eic".
+- reg: Define the base and range of the I/O address space containing
+ the GPIO controller registers.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Should be <2>. The first cell is the gpio number and
+ the second cell is used to specify optional parameters.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be <2>. Specifies the number of cells needed
+ to encode interrupt source.
+- interrupts: Should be the port interrupt shared by all the gpios.
+
+Example:
+ eic_debounce: gpio@40210000 {
+ compatible = "sprd,sc9860-eic-debounce";
+ reg = <0 0x40210000 0 0x80>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ eic_latch: gpio@40210080 {
+ compatible = "sprd,sc9860-eic-latch";
+ reg = <0 0x40210080 0 0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ eic_async: gpio@402100a0 {
+ compatible = "sprd,sc9860-eic-async";
+ reg = <0 0x402100a0 0 0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ eic_sync: gpio@402100c0 {
+ compatible = "sprd,sc9860-eic-sync";
+ reg = <0 0x402100c0 0 0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pmic_eic: gpio@300 {
+ compatible = "sprd,sc27xx-eic";
+ reg = <0x300>;
+ interrupt-parent = <&sc2731_pmic>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };