diff options
Diffstat (limited to 'Bindings/input')
| -rw-r--r-- | Bindings/input/atmel,maxtouch.yaml | 32 | ||||
| -rw-r--r-- | Bindings/input/input.yaml | 7 | ||||
| -rw-r--r-- | Bindings/input/iqs626a.yaml | 843 | ||||
| -rw-r--r-- | Bindings/input/touchscreen/azoteq,iqs5xx.yaml | 75 | ||||
| -rw-r--r-- | Bindings/input/touchscreen/hycon,hy46xx.yaml | 119 | ||||
| -rw-r--r-- | Bindings/input/touchscreen/ilitek_ts_i2c.yaml | 73 | ||||
| -rw-r--r-- | Bindings/input/touchscreen/melfas,mms114.yaml | 87 | ||||
| -rw-r--r-- | Bindings/input/touchscreen/mstar,msg2638.yaml | 69 |
8 files changed, 1304 insertions, 1 deletions
diff --git a/Bindings/input/atmel,maxtouch.yaml b/Bindings/input/atmel,maxtouch.yaml index 8c6418f76e94..3ec579d63570 100644 --- a/Bindings/input/atmel,maxtouch.yaml +++ b/Bindings/input/atmel,maxtouch.yaml @@ -39,6 +39,13 @@ properties: (active low). The line must be flagged with GPIO_ACTIVE_LOW. + wake-gpios: + maxItems: 1 + description: + Optional GPIO specifier for the touchscreen's wake pin + (active low). The line must be flagged with + GPIO_ACTIVE_LOW. + linux,gpio-keymap: $ref: /schemas/types.yaml#/definitions/uint32-array description: | @@ -53,6 +60,29 @@ properties: or experiment to determine which bit corresponds to which input. Use KEY_RESERVED for unused padding values. + atmel,wakeup-method: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The WAKE line is an active-low input that is used to wake up the touch + controller from deep-sleep mode before communication with the controller + could be started. This optional feature used to minimize current + consumption when the controller is in deep sleep mode. This feature is + relevant only to some controller families, like mXT1386 controller for + example. + + The WAKE pin can be connected in one of the following ways: + 1) left permanently low + 2) connected to the I2C-compatible SCL pin + 3) connected to a GPIO pin on the host + enum: + - 0 # ATMEL_MXT_WAKEUP_NONE + - 1 # ATMEL_MXT_WAKEUP_I2C_SCL + - 2 # ATMEL_MXT_WAKEUP_GPIO + default: 0 + + wakeup-source: + type: boolean + required: - compatible - reg @@ -63,6 +93,7 @@ additionalProperties: false examples: - | #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/input/atmel-maxtouch.h> #include <dt-bindings/gpio/gpio.h> i2c { #address-cells = <1>; @@ -75,6 +106,7 @@ examples: reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; vdda-supply = <&ab8500_ldo_aux2_reg>; vdd-supply = <&ab8500_ldo_aux5_reg>; + atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>; }; }; diff --git a/Bindings/input/input.yaml b/Bindings/input/input.yaml index ab407f266bef..d41d8743aad4 100644 --- a/Bindings/input/input.yaml +++ b/Bindings/input/input.yaml @@ -32,6 +32,11 @@ properties: Duration in seconds which the key should be kept pressed for device to power off automatically. Device with key pressed shutdown feature can specify this property. - $ref: /schemas/types.yaml#/definitions/uint32 + + reset-time-sec: + description: + Duration in seconds which the key should be kept pressed for device to + reset automatically. Device with key pressed reset feature can specify + this property. additionalProperties: true diff --git a/Bindings/input/iqs626a.yaml b/Bindings/input/iqs626a.yaml new file mode 100644 index 000000000000..0cb736c541c9 --- /dev/null +++ b/Bindings/input/iqs626a.yaml @@ -0,0 +1,843 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/iqs626a.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS626A Capacitive Touch Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS626A is a 14-channel capacitive touch controller that features + additional Hall-effect and inductive sensing capabilities. + + Link to datasheet: https://www.azoteq.com/ + +allOf: + - $ref: touchscreen/touchscreen.yaml# + +properties: + compatible: + const: azoteq,iqs626a + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + azoteq,suspend-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the power mode during suspend as follows: + 0: Automatic (same as normal runtime, i.e. suspend/resume disabled) + 1: Low power (all sensing at a reduced reporting rate) + 2: Ultra-low power (ULP channel proximity sensing) + 3: Halt (no sensing) + + azoteq,clk-div: + type: boolean + description: Divides the device's core clock by a factor of 4. + + azoteq,ulp-enable: + type: boolean + description: + Permits the device to automatically enter ultra-low-power mode from low- + power mode. + + azoteq,ulp-update: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + default: 3 + description: | + Specifies the rate at which the trackpad, generic and Hall channels are + updated during ultra-low-power mode as follows: + 0: 8 + 1: 13 + 2: 28 + 3: 54 + 4: 89 + 5: 135 + 6: 190 + 7: 256 + + azoteq,ati-band-disable: + type: boolean + description: Disables the ATI band check. + + azoteq,ati-lp-only: + type: boolean + description: Limits automatic ATI to low-power mode. + + azoteq,gpio3-select: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + default: 1 + description: | + Selects the channel or group of channels for which the GPIO3 pin + represents touch state as follows: + 0: None + 1: ULP channel + 2: Trackpad + 3: Trackpad + 4: Generic channel 0 + 5: Generic channel 1 + 6: Generic channel 2 + 7: Hall channel + + azoteq,reseed-select: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the event(s) that prompt the device to reseed (i.e. reset the + long-term average) of an associated channel as follows: + 0: None + 1: Proximity + 2: Proximity or touch + 3: Proximity, touch or deep touch + + azoteq,thresh-extend: + type: boolean + description: Multiplies all touch and deep-touch thresholds by 4. + + azoteq,tracking-enable: + type: boolean + description: + Enables all associated channels to track their respective reference + channels. + + azoteq,reseed-offset: + type: boolean + description: + Applies an 8-count offset to all long-term averages upon either ATI or + reseed events. + + azoteq,rate-np-ms: + minimum: 0 + maximum: 255 + default: 150 + description: Specifies the report rate (in ms) during normal-power mode. + + azoteq,rate-lp-ms: + minimum: 0 + maximum: 255 + default: 150 + description: Specifies the report rate (in ms) during low-power mode. + + azoteq,rate-ulp-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + default: 0 + description: Specifies the report rate (in ms) during ultra-low-power mode. + + azoteq,timeout-pwr-ms: + multipleOf: 512 + minimum: 0 + maximum: 130560 + default: 2560 + description: + Specifies the length of time (in ms) to wait for an event before moving + from normal-power mode to low-power mode, or (if 'azoteq,ulp-enable' is + present) from low-power mode to ultra-low-power mode. + + azoteq,timeout-lta-ms: + multipleOf: 512 + minimum: 0 + maximum: 130560 + default: 40960 + description: + Specifies the length of time (in ms) to wait before resetting the long- + term average of all channels. Specify the maximum timeout to disable it + altogether. + + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +patternProperties: + "^ulp-0|generic-[0-2]|hall$": + type: object + description: + Represents a single sensing channel. A channel is active if defined and + inactive otherwise. + + properties: + azoteq,ati-exclude: + type: boolean + description: + Prevents the channel from participating in an ATI event that is + manually triggered during initialization. + + azoteq,reseed-disable: + type: boolean + description: + Prevents the channel from being reseeded if the long-term average + timeout (defined in 'azoteq,timeout-lta') expires. + + azoteq,meas-cap-decrease: + type: boolean + description: + Decreases the internal measurement capacitance from 60 pF to 15 pF. + + azoteq,rx-inactive: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 0 + description: | + Specifies how inactive CRX pins are to be terminated as follows: + 0: VSS + 1: Floating + 2: VREG (generic channels only) + + azoteq,linearize: + type: boolean + description: + Enables linearization of the channel's counts (generic and Hall + channels) or inverts the polarity of the channel's proximity or + touch states (ULP channel). + + azoteq,dual-direction: + type: boolean + description: + Specifies that the channel's long-term average is to freeze in the + presence of either increasing or decreasing counts, thereby permit- + ting events to be reported in either direction. + + azoteq,filt-disable: + type: boolean + description: Disables raw count filtering for the channel. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the channel's ATI mode as follows: + 0: Disabled + 1: Semi-partial + 2: Partial + 3: Full + + The default value is a function of the channel and the device's reset + user interface (RUI); reference the datasheet for further information + about the available RUI options. + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [75, 100, 150, 200] + description: + Specifies the channel's ATI base. The default value is a function + of the channel and the device's RUI. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 32 + minimum: 0 + maximum: 2016 + description: + Specifies the channel's ATI target. The default value is a function + of the channel and the device's RUI. + + azoteq,cct-increase: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 16 + default: 0 + description: + Specifies the degree to which the channel's charge cycle time is to + be increased, with 0 representing no increase. The maximum value is + limited to 4 in the case of the ULP channel, and the property is un- + available entirely in the case of the Hall channel. + + azoteq,proj-bias: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the bias current applied during projected-capacitance + sensing as follows: + 0: 2.5 uA + 1: 5 uA + 2: 10 uA + 3: 20 uA + + This property is unavailable in the case of the Hall channel. + + azoteq,sense-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + description: | + Specifies the channel's sensing frequency as follows (parenthesized + numbers represent the frequency if 'azoteq,clk-div' is present): + 0: 4 MHz (1 MHz) + 1: 2 MHz (500 kHz) + 2: 1 MHz (250 kHz) + 3: 500 kHz (125 kHz) + + This property is unavailable in the case of the Hall channel. The + default value is a function of the channel and the device's RUI. + + azoteq,ati-band-tighten: + type: boolean + description: + Tightens the ATI band from 1/8 to 1/16 of the desired target (ULP and + generic channels only). + + azoteq,proj-enable: + type: boolean + description: Enables projected-capacitance sensing (ULP channel only). + + azoteq,filt-str-np-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during normal-power mode (ULP + and generic channels only). + + azoteq,filt-str-lp-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during low-power mode (ULP and + generic channels only). + + azoteq,filt-str-np-lta: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the long-term average filter strength during normal-power + mode (ULP and generic channels only). + + azoteq,filt-str-lp-lta: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the long-term average filter strength during low-power mode + (ULP and generic channels only). + + azoteq,rx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the CRX pin(s) associated with the channel. + + This property is unavailable in the case of the Hall channel. The + default value is a function of the channel and the device's RUI. + + azoteq,tx-enable: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 8 + items: + minimum: 0 + maximum: 7 + description: + Specifies the TX pin(s) associated with the channel. + + This property is unavailable in the case of the Hall channel. The + default value is a function of the channel and the device's RUI. + + azoteq,local-cap-size: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4] + default: 0 + description: | + Specifies the capacitance to be added to the channel as follows: + 0: 0 pF + 1: 0.5 pF + 2: 1.0 pF + 3: 1.5 pF + 4: 2.0 pF + + This property is unavailable in the case of the ULP or Hall channels. + + azoteq,sense-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 8, 9, 12, 14, 15] + description: | + Specifies the channel's sensing mode as follows: + 0: Self capacitance + 1: Projected capacitance + 8: Self inductance + 9: Mutual inductance + 12: External + 14: Hall effect + 15: Temperature + + This property is unavailable in the case of the ULP or Hall channels. + The default value is a function of the channel and the device's RUI. + + azoteq,tx-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the inductive sensing excitation frequency as follows + (parenthesized numbers represent the frequency if 'azoteq,clk-div' + is present): + 0: 16 MHz (4 MHz) + 1: 8 MHz (2 MHz) + 2: 4 MHz (1 MHz) + 3: 2 MHz (500 kHz) + + This property is unavailable in the case of the ULP or Hall channels. + + azoteq,invert-enable: + type: boolean + description: + Inverts the polarity of the states reported for proximity, touch and + deep-touch events relative to their respective thresholds (generic + channels only). + + azoteq,comp-disable: + type: boolean + description: + Disables compensation for the channel (generic channels only). + + azoteq,static-enable: + type: boolean + description: + Enables the static front-end for the channel (generic channels only). + + azoteq,assoc-select: + $ref: /schemas/types.yaml#/definitions/string-array + minItems: 1 + maxItems: 6 + items: + enum: + - ulp-0 + - trackpad-3x2 + - trackpad-3x3 + - generic-0 + - generic-1 + - generic-2 + - hall + description: + Specifies the associated channels for which the channel serves as a + reference channel. By default, no channels are selected. This prop- + erty is only available for the generic channels. + + azoteq,assoc-weight: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 0 + description: + Specifies the channel's impact weight if it acts as an associated + channel (0 = 0% impact, 255 = 200% impact). This property is only + available for the generic channels. + + patternProperties: + "^event-(prox|touch|deep)(-alt)?$": + type: object + description: + Represents a proximity, touch or deep-touch event reported by the + channel in response to a decrease in counts. Node names suffixed with + '-alt' instead correspond to an increase in counts. + + By default, the long-term average tracks an increase in counts such + that only events corresponding to a decrease in counts are reported + (refer to the datasheet for more information). + + Specify 'azoteq,dual-direction' to freeze the long-term average when + the counts increase or decrease such that events of either direction + can be reported. Alternatively, specify 'azoteq,invert-enable' to in- + vert the polarity of the states reported by the channel. + + Complementary events (e.g. event-touch and event-touch-alt) can both + be present and specify different key or switch codes, but not differ- + ent thresholds or hysteresis (if applicable). + + Proximity events are unavailable in the case of the Hall channel, and + deep-touch events are only available for the generic channels. Unless + otherwise specified, default values are a function of the channel and + the device's RUI. + + properties: + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + description: Specifies the threshold for the event. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: + Specifies the hysteresis for the event (touch and deep-touch + events only). + + linux,code: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Numeric key or switch code associated with the event. + + linux,input-type: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 5] + description: + Specifies whether the event is to be interpreted as a key (1) or + a switch (5). By default, Hall-channel events are interpreted as + switches and all others are interpreted as keys. + + dependencies: + linux,input-type: ["linux,code"] + + additionalProperties: false + + dependencies: + azoteq,assoc-weight: ["azoteq,assoc-select"] + + additionalProperties: false + + "^trackpad-3x[2-3]$": + type: object + description: + Represents all channels associated with the trackpad. The channels are + collectively active if the trackpad is defined and inactive otherwise. + + properties: + azoteq,ati-exclude: + type: boolean + description: + Prevents the trackpad channels from participating in an ATI event + that is manually triggered during initialization. + + azoteq,reseed-disable: + type: boolean + description: + Prevents the trackpad channels from being reseeded if the long-term + average timeout (defined in 'azoteq,timeout-lta') expires. + + azoteq,meas-cap-decrease: + type: boolean + description: + Decreases the internal measurement capacitance from 60 pF to 15 pF. + + azoteq,rx-inactive: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + default: 0 + description: | + Specifies how inactive CRX pins are to be terminated as follows: + 0: VSS + 1: Floating + + azoteq,linearize: + type: boolean + description: Inverts the polarity of the trackpad's touch state. + + azoteq,dual-direction: + type: boolean + description: + Specifies that the trackpad's long-term averages are to freeze in + the presence of either increasing or decreasing counts, thereby + permitting events to be reported in either direction. + + azoteq,filt-disable: + type: boolean + description: Disables raw count filtering for the trackpad channels. + + azoteq,ati-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the trackpad's ATI mode as follows: + 0: Disabled + 1: Semi-partial + 2: Partial + 3: Full + + azoteq,ati-base: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 6 + maxItems: 9 + items: + minimum: 45 + maximum: 300 + default: [45, 45, 45, 45, 45, 45, 45, 45, 45] + description: Specifies each individual trackpad channel's ATI base. + + azoteq,ati-target: + $ref: /schemas/types.yaml#/definitions/uint32 + multipleOf: 32 + minimum: 0 + maximum: 2016 + default: 0 + description: Specifies the trackpad's ATI target. + + azoteq,cct-increase: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 4 + default: 0 + description: + Specifies the degree to which the trackpad's charge cycle time is to + be increased, with 0 representing no increase. + + azoteq,proj-bias: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the bias current applied during projected-capacitance + sensing as follows: + 0: 2.5 uA + 1: 5 uA + 2: 10 uA + 3: 20 uA + + azoteq,sense-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: | + Specifies the trackpad's sensing frequency as follows (parenthesized + numbers represent the frequency if 'azoteq,clk-div' is present): + 0: 4 MHz (1 MHz) + 1: 2 MHz (500 kHz) + 2: 1 MHz (250 kHz) + 3: 500 kHz (125 kHz) + + azoteq,ati-band-tighten: + type: boolean + description: + Tightens the ATI band from 1/8 to 1/16 of the desired target. + + azoteq,thresh: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 6 + maxItems: 9 + items: + minimum: 0 + maximum: 255 + default: [0, 0, 0, 0, 0, 0, 0, 0, 0] + description: + Specifies each individual trackpad channel's touch threshold. + + azoteq,hyst: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 0 + description: Specifies the trackpad's touch hysteresis. + + azoteq,lta-update: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + default: 0 + description: | + Specifies the update rate of the trackpad's long-term average during + ultra-low-power mode as follows: + 0: 2 + 1: 4 + 2: 8 + 3: 16 + 4: 32 + 5: 64 + 6: 128 + 7: 255 + + azoteq,filt-str-trackpad: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: Specifies the trackpad coordinate filter strength. + + azoteq,filt-str-np-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during normal-power mode. + + azoteq,filt-str-lp-cnt: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + default: 0 + description: + Specifies the raw count filter strength during low-power mode. + + linux,keycodes: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 6 + description: | + Specifies the numeric keycodes associated with each available gesture + in the following order (enter 0 for unused gestures): + 0: Positive flick or swipe in X direction + 1: Negative flick or swipe in X direction + 2: Positive flick or swipe in Y direction + 3: Negative flick or swipe in Y direction + 4: Tap + 5: Hold + + azoteq,gesture-swipe: + type: boolean + description: + Directs the device to interpret axial gestures as a swipe (finger + remains on trackpad) instead of a flick (finger leaves trackpad). + + azoteq,timeout-tap-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + default: 0 + description: + Specifies the length of time (in ms) within which a trackpad touch + must be released in order to be interpreted as a tap. + + azoteq,timeout-swipe-ms: + multipleOf: 16 + minimum: 0 + maximum: 4080 + default: 0 + description: + Specifies the length of time (in ms) within which an axial gesture + must be completed in order to be interpreted as a flick or swipe. + + azoteq,thresh-swipe: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + default: 0 + description: + Specifies the number of points across which an axial gesture must + travel in order to be interpreted as a flick or swipe. + + dependencies: + azoteq,gesture-swipe: ["linux,keycodes"] + azoteq,timeout-tap-ms: ["linux,keycodes"] + azoteq,timeout-swipe-ms: ["linux,keycodes"] + azoteq,thresh-swipe: ["linux,keycodes"] + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + iqs626a@44 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "azoteq,iqs626a"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + + azoteq,rate-np-ms = <16>; + azoteq,rate-lp-ms = <160>; + + azoteq,timeout-pwr-ms = <2560>; + azoteq,timeout-lta-ms = <32768>; + + ulp-0 { + azoteq,meas-cap-decrease; + + azoteq,ati-base = <75>; + azoteq,ati-target = <1024>; + + azoteq,rx-enable = <2>, <3>, <4>, + <5>, <6>, <7>; + + event-prox { + linux,code = <KEY_POWER>; + }; + }; + + trackpad-3x3 { + azoteq,filt-str-np-cnt = <1>; + azoteq,filt-str-lp-cnt = <1>; + + azoteq,hyst = <4>; + azoteq,thresh = <35>, <40>, <40>, + <38>, <33>, <38>, + <35>, <35>, <35>; + + azoteq,ati-mode = <3>; + azoteq,ati-base = <195>, <195>, <195>, + <195>, <195>, <195>, + <195>, <195>, <195>; + azoteq,ati-target = <512>; + + azoteq,proj-bias = <1>; + azoteq,sense-freq = <2>; + + linux,keycodes = <KEY_VOLUMEUP>, + <KEY_VOLUMEDOWN>, + <KEY_NEXTSONG>, + <KEY_PREVIOUSSONG>, + <KEY_PLAYPAUSE>, + <KEY_STOPCD>; + + azoteq,gesture-swipe; + azoteq,timeout-swipe-ms = <800>; + azoteq,timeout-tap-ms = <400>; + azoteq,thresh-swipe = <40>; + }; + + /* + * Preserve the default register settings for + * the temperature-tracking channel leveraged + * by reset user interface (RUI) 1. + * + * Scalar properties (e.g. ATI mode) are left + * untouched by simply omitting them; boolean + * properties must be specified explicitly as + * needed. + */ + generic-2 { + azoteq,reseed-disable; + azoteq,meas-cap-decrease; + azoteq,dual-direction; + azoteq,comp-disable; + azoteq,static-enable; + }; + + hall { + azoteq,reseed-disable; + azoteq,meas-cap-decrease; + + event-touch { + linux,code = <SW_LID>; + }; + }; + }; + }; + +... diff --git a/Bindings/input/touchscreen/azoteq,iqs5xx.yaml b/Bindings/input/touchscreen/azoteq,iqs5xx.yaml new file mode 100644 index 000000000000..b5f377215c09 --- /dev/null +++ b/Bindings/input/touchscreen/azoteq,iqs5xx.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/azoteq,iqs5xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Azoteq IQS550/572/525 Trackpad/Touchscreen Controller + +maintainers: + - Jeff LaBundy <jeff@labundy.com> + +description: | + The Azoteq IQS550, IQS572 and IQS525 trackpad and touchscreen controllers + employ projected-capacitance sensing and can track up to five independent + contacts. + + Link to datasheet: https://www.azoteq.com/ + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - azoteq,iqs550 + - azoteq,iqs572 + - azoteq,iqs525 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + wakeup-source: true + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@74 { + compatible = "azoteq,iqs550"; + reg = <0x74>; + interrupt-parent = <&gpio>; + interrupts = <27 IRQ_TYPE_LEVEL_HIGH>; + reset-gpios = <&gpio 22 (GPIO_ACTIVE_LOW | + GPIO_PUSH_PULL)>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + }; + }; + +... diff --git a/Bindings/input/touchscreen/hycon,hy46xx.yaml b/Bindings/input/touchscreen/hycon,hy46xx.yaml new file mode 100644 index 000000000000..942562f1e45b --- /dev/null +++ b/Bindings/input/touchscreen/hycon,hy46xx.yaml @@ -0,0 +1,119 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/hycon,hy46xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hycon HY46XX series touchscreen controller bindings + +description: | + There are 6 variants of the chip for various touch panel sizes and cover lens material + Glass: 0.3mm--4.0mm + PET/PMMA: 0.2mm--2.0mm + HY4613(B)-N048 < 6" + HY4614(B)-N068 7" .. 10.1" + HY4621-NS32 < 5" + HY4623-NS48 5.1" .. 7" + Glass: 0.3mm--8.0mm + PET/PMMA: 0.2mm--4.0mm + HY4633(B)-N048 < 6" + HY4635(B)-N048 < 7" .. 10.1" + +maintainers: + - Giulio Benetti <giulio.benetti@benettiengineering.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - hycon,hy4613 + - hycon,hy4614 + - hycon,hy4621 + - hycon,hy4623 + - hycon,hy4633 + - hycon,hy4635 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + vcc-supply: true + + hycon,threshold: + description: Allows setting the sensitivity in the range from 0 to 255. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 255 + + hycon,glove-enable: + type: boolean + description: Allows enabling glove setting. + + hycon,report-speed-hz: + description: Allows setting the report speed in Hertz. + minimum: 1 + maximum: 255 + + hycon,noise-filter-enable: + type: boolean + description: Allows enabling power noise filter. + + hycon,filter-data: + description: Allows setting how many samples throw before reporting touch + in the range from 0 to 5. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 5 + + hycon,gain: + description: Allows setting the sensitivity distance in the range from 0 to 5. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 5 + + hycon,edge-offset: + description: Allows setting the edge compensation in the range from 0 to 16. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 16 + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + interrupt-controller: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@1c { + compatible = "hycon,hy4633"; + reg = <0x1c>; + interrupt-parent = <&gpio2>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; + }; + }; + +... diff --git a/Bindings/input/touchscreen/ilitek_ts_i2c.yaml b/Bindings/input/touchscreen/ilitek_ts_i2c.yaml new file mode 100644 index 000000000000..a190e7baac31 --- /dev/null +++ b/Bindings/input/touchscreen/ilitek_ts_i2c.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/ilitek_ts_i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ilitek I2C Touchscreen Controller + +maintainers: + - Dmitry Torokhov <dmitry.torokhov@gmail.com> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + enum: + - ilitek,ili2130 + - ilitek,ili2131 + - ilitek,ili2132 + - ilitek,ili2316 + - ilitek,ili2322 + - ilitek,ili2323 + - ilitek,ili2326 + - ilitek,ili2520 + - ilitek,ili2521 + + reg: + const: 0x41 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + wakeup-source: + type: boolean + description: touchscreen can be used as a wakeup source. + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - reset-gpios + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@41 { + compatible = "ilitek,ili2520"; + reg = <0x41>; + + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + touchscreen-inverted-y; + wakeup-source; + }; + }; diff --git a/Bindings/input/touchscreen/melfas,mms114.yaml b/Bindings/input/touchscreen/melfas,mms114.yaml new file mode 100644 index 000000000000..62366886fb3e --- /dev/null +++ b/Bindings/input/touchscreen/melfas,mms114.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/melfas,mms114.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Melfas MMS114 family touchscreen controller bindings + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: touchscreen.yaml# + +properties: + $nodename: + pattern: "^touchscreen(@.*)?$" + + compatible: + items: + - enum: + - melfas,mms114 + - melfas,mms134s + - melfas,mms136 + - melfas,mms152 + - melfas,mms345l + + reg: + description: I2C address + + clock-frequency: + description: I2C client clock frequency, defined for host + minimum: 100000 + maximum: 400000 + + interrupts: + maxItems: 1 + + avdd-supply: + description: Analog power supply regulator on AVDD pin + + vdd-supply: + description: Digital power supply regulator on VDD pin + + touchscreen-size-x: true + touchscreen-size-y: true + touchscreen-fuzz-x: true + touchscreen-fuzz-y: true + touchscreen-fuzz-pressure: true + touchscreen-inverted-x: true + touchscreen-inverted-y: true + touchscreen-swapped-x-y: true + touchscreen-max-pressure: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupt-parent = <&gpio>; + interrupts = <39 IRQ_TYPE_EDGE_FALLING>; + avdd-supply = <&ldo1_reg>; + vdd-supply = <&ldo2_reg>; + touchscreen-size-x = <720>; + touchscreen-size-y = <1280>; + touchscreen-fuzz-x = <10>; + touchscreen-fuzz-y = <10>; + touchscreen-fuzz-pressure = <10>; + touchscreen-inverted-x; + touchscreen-inverted-y; + }; + }; + +... diff --git a/Bindings/input/touchscreen/mstar,msg2638.yaml b/Bindings/input/touchscreen/mstar,msg2638.yaml new file mode 100644 index 000000000000..3a42c23faf6f --- /dev/null +++ b/Bindings/input/touchscreen/mstar,msg2638.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/mstar,msg2638.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MStar msg2638 touchscreen controller Bindings + +maintainers: + - Vincent Knecht <vincent.knecht@mailoo.org> + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: mstar,msg2638 + + reg: + const: 0x26 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + + vdd-supply: + description: Power supply regulator for the chip + + vddio-supply: + description: Power supply regulator for the I2C bus + + touchscreen-size-x: true + touchscreen-size-y: true + +additionalProperties: false + +required: + - compatible + - reg + - interrupts + - reset-gpios + - touchscreen-size-x + - touchscreen-size-y + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + touchscreen@26 { + compatible = "mstar,msg2638"; + reg = <0x26>; + interrupt-parent = <&msmgpio>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&msmgpio 100 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_reset_default>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + touchscreen-size-x = <2048>; + touchscreen-size-y = <2048>; + }; + }; + +... |