diff options
Diffstat (limited to 'Bindings/mfd')
| -rw-r--r-- | Bindings/mfd/ac100.txt | 54 | ||||
| -rw-r--r-- | Bindings/mfd/act8945a.txt | 22 | ||||
| -rw-r--r-- | Bindings/mfd/altera-a10sr.txt | 46 | ||||
| -rw-r--r-- | Bindings/mfd/arizona.txt | 18 | ||||
| -rw-r--r-- | Bindings/mfd/aspeed-scu.txt | 18 | ||||
| -rw-r--r-- | Bindings/mfd/axp20x.txt | 34 | ||||
| -rw-r--r-- | Bindings/mfd/da9052-i2c.txt | 22 | ||||
| -rw-r--r-- | Bindings/mfd/lp873x.txt | 67 | ||||
| -rw-r--r-- | Bindings/mfd/max77620.txt | 12 | ||||
| -rw-r--r-- | Bindings/mfd/max77693.txt | 12 | ||||
| -rw-r--r-- | Bindings/mfd/qcom-pm8xxx.txt | 2 | ||||
| -rw-r--r-- | Bindings/mfd/qcom-rpm.txt | 15 | ||||
| -rw-r--r-- | Bindings/mfd/rk808.txt | 37 | ||||
| -rw-r--r-- | Bindings/mfd/rn5t618.txt | 23 | ||||
| -rw-r--r-- | Bindings/mfd/samsung,exynos5433-lpass.txt | 70 | ||||
| -rw-r--r-- | Bindings/mfd/stmpe.txt | 2 | ||||
| -rw-r--r-- | Bindings/mfd/tps65086.txt | 2 | ||||
| -rw-r--r-- | Bindings/mfd/twl6040.txt | 5 |
18 files changed, 420 insertions, 41 deletions
diff --git a/Bindings/mfd/ac100.txt b/Bindings/mfd/ac100.txt new file mode 100644 index 000000000000..b8ef00667599 --- /dev/null +++ b/Bindings/mfd/ac100.txt @@ -0,0 +1,54 @@ +X-Powers AC100 Codec/RTC IC Device Tree bindings + +AC100 is a audio codec and RTC subsystem combo IC. The 2 parts are +separated, including power supplies and interrupt lines, but share +a common register address space and host interface. + +Required properties: +- compatible: "x-powers,ac100" +- reg: The I2C slave address or RSB hardware address for the chip +- sub-nodes: + - codec + - compatible: "x-powers,ac100-codec" + - interrupt-parent: The parent interrupt controller + - interrupts: SoC NMI / GPIO interrupt connected to the + IRQ_AUDIO pin + - #clock-cells: Shall be 0 + - clock-output-names: "4M_adda" + + - see clock/clock-bindings.txt for common clock bindings + + - rtc + - compatible: "x-powers,ac100-rtc" + - interrupt-parent: The parent interrupt controller + - interrupts: SoC NMI / GPIO interrupt connected to the + IRQ_RTC pin + - clocks: A phandle to the codec's "4M_adda" clock + - #clock-cells: Shall be 1 + - clock-output-names: "cko1_rtc", "cko2_rtc", "cko3_rtc" + + - see clock/clock-bindings.txt for common clock bindings + +Example: + +ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", "cko2_rtc", "cko3_rtc"; + }; +}; diff --git a/Bindings/mfd/act8945a.txt b/Bindings/mfd/act8945a.txt index f71283055685..462819ac3da8 100644 --- a/Bindings/mfd/act8945a.txt +++ b/Bindings/mfd/act8945a.txt @@ -14,13 +14,6 @@ Example: reg = <0x5b>; status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_charger_chglev>; - active-semi,chglev-gpio = <&pioA 12 GPIO_ACTIVE_HIGH>; - active-semi,input-voltage-threshold-microvolt = <6600>; - active-semi,precondition-timeout = <40>; - active-semi,total-timeout = <3>; - active-semi,vsel-high; regulators { @@ -73,4 +66,19 @@ Example: regulator-always-on; }; }; + + charger { + compatible = "active-semi,act8945a-charger"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; + interrupt-parent = <&pioA>; + interrupts = <45 GPIO_ACTIVE_LOW>; + + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + status = "okay"; + }; }; diff --git a/Bindings/mfd/altera-a10sr.txt b/Bindings/mfd/altera-a10sr.txt new file mode 100644 index 000000000000..ea151f295ad7 --- /dev/null +++ b/Bindings/mfd/altera-a10sr.txt @@ -0,0 +1,46 @@ +* Altera Arria10 Development Kit System Resource Chip + +Required parent device properties: +- compatible : "altr,a10sr" +- spi-max-frequency : Maximum SPI frequency. +- reg : The SPI Chip Select address for the Arria10 + System Resource chip +- interrupt-parent : The parent interrupt controller. +- interrupts : The interrupt line the device is connected to. +- interrupt-controller : Marks the device node as an interrupt controller. +- #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + +The A10SR consists of these sub-devices: + +Device Description +------ ---------- +a10sr_gpio GPIO Controller + +Arria10 GPIO +Required Properties: +- compatible : Should be "altr,a10sr-gpio" +- gpio-controller : Marks the device node as a GPIO Controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + +Example: + + resource-manager@0 { + compatible = "altr,a10sr"; + reg = <0>; + spi-max-frequency = <100000>; + interrupt-parent = <&portb>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + a10sr_gpio: gpio-controller { + compatible = "altr,a10sr-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; diff --git a/Bindings/mfd/arizona.txt b/Bindings/mfd/arizona.txt index a6e2ea41160c..8f2e2822238d 100644 --- a/Bindings/mfd/arizona.txt +++ b/Bindings/mfd/arizona.txt @@ -85,6 +85,24 @@ Optional properties: present, the number of values should be less than or equal to the number of inputs, unspecified inputs will use the chip default. + - wlf,max-channels-clocked : The maximum number of channels to be clocked on + each AIF, useful for I2S systems with multiple data lines being mastered. + Specify one cell for each AIF to be configured, specify zero for AIFs that + should be handled normally. + If present, number of cells must be less than or equal to the number of + AIFs. If less than the number of AIFs, for cells that have not been + specified the corresponding AIFs will be treated as default setting. + + - wlf,spk-fmt : PDM speaker data format, must contain 2 cells (OUT5 and OUT6). + See the datasheet for values. + The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, + wm8998, wm1814) + + - wlf,spk-mute : PDM speaker mute setting, must contain 2 cells (OUT5 and OUT6). + See the datasheet for values. + The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, + wm8998, wm1814) + - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if they are being externally supplied. As covered in Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Bindings/mfd/aspeed-scu.txt b/Bindings/mfd/aspeed-scu.txt new file mode 100644 index 000000000000..4fc5b83726d6 --- /dev/null +++ b/Bindings/mfd/aspeed-scu.txt @@ -0,0 +1,18 @@ +The Aspeed System Control Unit manages the global behaviour of the SoC, +configuring elements such as clocks, pinmux, and reset. + +Required properties: +- compatible: One of: + "aspeed,ast2400-scu", "syscon", "simple-mfd" + "aspeed,g4-scu", "syscon", "simple-mfd" + "aspeed,ast2500-scu", "syscon", "simple-mfd" + "aspeed,g5-scu", "syscon", "simple-mfd" + +- reg: contains the offset and length of the SCU memory region + +Example: + +syscon: syscon@1e6e2000 { + compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; +}; diff --git a/Bindings/mfd/axp20x.txt b/Bindings/mfd/axp20x.txt index d20b1034e967..8f3ad9ab4637 100644 --- a/Bindings/mfd/axp20x.txt +++ b/Bindings/mfd/axp20x.txt @@ -10,7 +10,8 @@ axp809 (X-Powers) Required properties: - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209", - "x-powers,axp221", "x-powers,axp223", "x-powers,axp809" + "x-powers,axp221", "x-powers,axp223", "x-powers,axp806", + "x-powers,axp809" - reg: The I2C slave address or RSB hardware address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin @@ -22,6 +23,11 @@ Optional properties: AXP152/20X: range: 750-1875, Default: 1.5 MHz AXP22X/80X: range: 1800-4050, Default: 3 MHz +- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the + N_VBUSEN pin is used as an output pin to control an external + regulator to drive the OTG VBus, rather then as an input pin + which signals whether the board is driving OTG VBus or not. + - <input>-supply: a phandle to the regulator supply node. May be omitted if inputs are unregulated, such as using the IPSOUT output from the PMIC. @@ -42,7 +48,6 @@ Optional properties for DCDC regulators: probably makes sense for HiFi audio related applications that aren't battery constrained. - AXP202/AXP209 regulators, type, and corresponding input supply names: Regulator Type Supply Name Notes @@ -79,6 +84,31 @@ ELDO3 : LDO : eldoin-supply : shared supply LDO_IO0 : LDO : ips-supply : GPIO 0 LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator + +AXP806 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDCA : DC-DC buck : vina-supply : poly-phase capable +DCDCB : DC-DC buck : vinb-supply : poly-phase capable +DCDCC : DC-DC buck : vinc-supply : poly-phase capable +DCDCD : DC-DC buck : vind-supply : poly-phase capable +DCDCE : DC-DC buck : vine-supply : poly-phase capable +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +BLDO1 : LDO : bldoin-supply : shared supply +BLDO2 : LDO : bldoin-supply : shared supply +BLDO3 : LDO : bldoin-supply : shared supply +BLDO4 : LDO : bldoin-supply : shared supply +CLDO1 : LDO : cldoin-supply : shared supply +CLDO2 : LDO : cldoin-supply : shared supply +CLDO3 : LDO : cldoin-supply : shared supply +SW : On/Off Switch : swin-supply + +Additionally, the AXP806 DC-DC regulators support poly-phase arrangements +for higher output current. The possible groupings are: A+B, A+B+C, D+E. AXP809 regulators, type, and corresponding input supply names: diff --git a/Bindings/mfd/da9052-i2c.txt b/Bindings/mfd/da9052-i2c.txt index 1857f4a6b9a9..9554292dc6cb 100644 --- a/Bindings/mfd/da9052-i2c.txt +++ b/Bindings/mfd/da9052-i2c.txt @@ -8,10 +8,13 @@ Sub-nodes: - regulators : Contain the regulator nodes. The DA9052/53 regulators are bound using their names as listed below: - buck0 : regulator BUCK0 - buck1 : regulator BUCK1 - buck2 : regulator BUCK2 - buck3 : regulator BUCK3 + buck1 : regulator BUCK CORE + buck2 : regulator BUCK PRO + buck3 : regulator BUCK MEM + buck4 : regulator BUCK PERI + ldo1 : regulator LDO1 + ldo2 : regulator LDO2 + ldo3 : regulator LDO3 ldo4 : regulator LDO4 ldo5 : regulator LDO5 ldo6 : regulator LDO6 @@ -19,9 +22,6 @@ Sub-nodes: ldo8 : regulator LDO8 ldo9 : regulator LDO9 ldo10 : regulator LDO10 - ldo11 : regulator LDO11 - ldo12 : regulator LDO12 - ldo13 : regulator LDO13 The bindings details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt @@ -36,22 +36,22 @@ i2c@63fc8000 { /* I2C1 */ reg = <0x48>; regulators { - buck0 { + buck1 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck1 { + buck2 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck2 { + buck3 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; - buck3 { + buck4 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; diff --git a/Bindings/mfd/lp873x.txt b/Bindings/mfd/lp873x.txt new file mode 100644 index 000000000000..ae9cf39bd101 --- /dev/null +++ b/Bindings/mfd/lp873x.txt @@ -0,0 +1,67 @@ +TI LP873X PMIC MFD driver + +Required properties: + - compatible: "ti,lp8732", "ti,lp8733" + - reg: I2C slave address. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - xxx-in-supply: Phandle to parent supply node of each regulator + populated under regulators node. xxx can be + buck0, buck1, ldo0 or ldo1. + - regulators: List of child nodes that specify the regulator + initialization data. +Example: + +pmic: lp8733@60 { + compatible = "ti,lp8733"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + + buck0-in-supply = <&vsys_3v3>; + buck1-in-supply = <&vsys_3v3>; + ldo0-in-supply = <&vsys_3v3>; + ldo1-in-supply = <&vsys_3v3>; + + regulators { + lp8733_buck0: buck0 { + regulator-name = "lp8733-buck0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-min-microamp = <1500000>; + regulator-max-microamp = <4000000>; + regulator-ramp-delay = <10000>; + regulator-always-on; + regulator-boot-on; + }; + + lp8733_buck1: buck1 { + regulator-name = "lp8733-buck1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-min-microamp = <1500000>; + regulator-max-microamp = <4000000>; + regulator-ramp-delay = <10000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8733_ldo0: ldo0 { + regulator-name = "lp8733-ldo0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8733_ldo1: ldo1 { + regulator-name = "lp8733-ldo1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-boot-on; + }; + }; +}; diff --git a/Bindings/mfd/max77620.txt b/Bindings/mfd/max77620.txt index 2ad44f7e4880..9c16d51cc15b 100644 --- a/Bindings/mfd/max77620.txt +++ b/Bindings/mfd/max77620.txt @@ -106,6 +106,18 @@ Here supported time periods by device in microseconds are as follows: MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. +-maxim,power-ok-control: configure map power ok bit + 1: Enables POK(Power OK) to control nRST_IO and GPIO1 + POK function. + 0: Disables POK control. + if property missing, do not configure MPOK bit. + If POK mapping is enabled for GPIO1/nRST_IO then, + GPIO1/nRST_IO pins are HIGH only if all rails + that have POK control enabled are HIGH. + If any of the rails goes down(which are enabled for POK + control) then, GPIO1/nRST_IO goes LOW. + this property is valid for max20024 only. + For DT binding details of different sub modules like GPIO, pincontrol, regulator, power, please refer respective device-tree binding document under their respective sub-system directories. diff --git a/Bindings/mfd/max77693.txt b/Bindings/mfd/max77693.txt index d3425846aa5b..6a1ae3a2b77f 100644 --- a/Bindings/mfd/max77693.txt +++ b/Bindings/mfd/max77693.txt @@ -17,28 +17,28 @@ Required properties: - interrupt-parent : The parent interrupt controller. Optional properties: -- regulators : The regulators of max77693 have to be instantiated under subnod +- regulators : The regulators of max77693 have to be instantiated under subnode named "regulators" using the following format. regulators { - regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER - standard regulator constratints[*]. + regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER + standard regulator constraints[*]. }; [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide users with tactile feedback. PWM period and duty-cycle are varied in - order to provide the approprite level of feedback. + order to provide the appropriate level of feedback. Required properties: - - compatible : Must be "maxim,max77693-hpatic" + - compatible : Must be "maxim,max77693-haptic" - haptic-supply : power supply for the haptic motor [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - pwms : phandle to the physical PWM(Pulse Width Modulation) device. PWM properties should be named "pwms". And number of cell is different for each pwm device. - To get more informations, please refer to documentaion. + To get more information, please refer to documentation. [*] refer Documentation/devicetree/bindings/pwm/pwm.txt - charger : Node configuring the charger driver. diff --git a/Bindings/mfd/qcom-pm8xxx.txt b/Bindings/mfd/qcom-pm8xxx.txt index f24f33409164..9e5eba4a4f0d 100644 --- a/Bindings/mfd/qcom-pm8xxx.txt +++ b/Bindings/mfd/qcom-pm8xxx.txt @@ -10,6 +10,7 @@ voltages and other various functionality to Qualcomm SoCs. Value type: <string> Definition: must be one of: "qcom,pm8058" + "qcom,pm8821" "qcom,pm8921" - #address-cells: @@ -62,6 +63,7 @@ The below bindings specify the set of valid subnodes. "qcom,pm8058-rtc" "qcom,pm8921-rtc" "qcom,pm8941-rtc" + "qcom,pm8018-rtc" - reg: Usage: required diff --git a/Bindings/mfd/qcom-rpm.txt b/Bindings/mfd/qcom-rpm.txt index b98b291a31ba..485bc59fcc48 100644 --- a/Bindings/mfd/qcom-rpm.txt +++ b/Bindings/mfd/qcom-rpm.txt @@ -13,6 +13,7 @@ frequencies. "qcom,rpm-msm8660" "qcom,rpm-msm8960" "qcom,rpm-ipq8064" + "qcom,rpm-mdm9615" - reg: Usage: required @@ -59,6 +60,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8058-regulators" "qcom,rpm-pm8901-regulators" "qcom,rpm-pm8921-regulators" + "qcom,rpm-pm8018-regulators" - vdd_l0_l1_lvs-supply: - vdd_l2_l11_l12-supply: @@ -137,6 +139,15 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vin_lvs1-supply: +- vdd_l7-supply: +- vdd_l8-supply: +- vdd_l9_l10_l11_l12-supply: + Usage: optional (pm8018 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -156,6 +167,10 @@ pm8921: l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch, ncp +pm8018: + s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, + l12, l14, lvs1 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt - with additional custom properties described below: diff --git a/Bindings/mfd/rk808.txt b/Bindings/mfd/rk808.txt index 4ca6aab4273a..9636ae8d8d41 100644 --- a/Bindings/mfd/rk808.txt +++ b/Bindings/mfd/rk808.txt @@ -1,7 +1,11 @@ -RK808 Power Management Integrated Circuit +RK8XX Power Management Integrated Circuit + +The rk8xx family current members: +rk808 +rk818 Required properties: -- compatible: "rockchip,rk808" +- compatible: "rockchip,rk808", "rockchip,rk818" - reg: I2C slave address - interrupt-parent: The parent interrupt controller. - interrupts: the interrupt outputs of the controller. @@ -13,6 +17,8 @@ Optional properties: default output clock name - rockchip,system-power-controller: Telling whether or not this pmic is controlling the system power. + +Optional RK808 properties: - vcc1-supply: The input supply for DCDC_REG1 - vcc2-supply: The input supply for DCDC_REG2 - vcc3-supply: The input supply for DCDC_REG3 @@ -29,7 +35,20 @@ Optional properties: the gpio controller. If DVS GPIOs aren't present, voltage changes will happen very quickly with no slow ramp time. -Regulators: All the regulators of RK808 to be instantiated shall be +Optional RK818 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- boost-supply: The input supply for DCDC_BOOST +- vcc6-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc7-supply: The input supply for LDO_REG3, LDO_REG5 and LDO_REG7 +- vcc8-supply: The input supply for LDO_REG4, LDO_REG6 and LDO_REG8 +- vcc9-supply: The input supply for LDO_REG9 and SWITCH_REG +- h_5v-supply: The input supply for HDMI_SWITCH +- usb-supply: The input supply for OTG_SWITCH + +Regulators: All the regulators of RK8XX to be instantiated shall be listed in a child node named 'regulators'. Each regulator is represented by a child node of the 'regulators' node. @@ -48,6 +67,18 @@ number as described in RK808 datasheet. - SWITCH_REGn - valid values for n are 1 to 2 +Following regulators of the RK818 PMIC block are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK818 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 9. + - SWITCH_REG + - HDMI_SWITCH + - OTG_SWITCH + Standard regulator bindings are used inside regulator subnodes. Check Documentation/devicetree/bindings/regulator/regulator.txt for more details diff --git a/Bindings/mfd/rn5t618.txt b/Bindings/mfd/rn5t618.txt index 937785a3eddc..65c23263cc54 100644 --- a/Bindings/mfd/rn5t618.txt +++ b/Bindings/mfd/rn5t618.txt @@ -1,18 +1,25 @@ -* Ricoh RN5T618 PMIC +* Ricoh RN5T567/RN5T618 PMIC -Ricoh RN5T618 is a power management IC which integrates 3 step-down -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled -through a I2C interface. +Ricoh RN5T567/RN5T618/RC5T619 is a power management IC family which +integrates 3 to 5 step-down DCDC converters, 7 to 10 low-dropout regulators, +GPIOs, and a watchdog timer. It can be controlled through an I2C interface. +The RN5T618/RC5T619 provides additionally a Li-ion battery charger, +fuel gauge, and an ADC. +The RC5T619 additionnally includes USB charger detection and an RTC. Required properties: - - compatible: should be "ricoh,rn5t618" + - compatible: must be one of + "ricoh,rn5t567" + "ricoh,rn5t618" + "ricoh,rc5t619" - reg: the I2C slave address of the device Sub-nodes: - regulators: the node is required if the regulator functionality is - needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, - LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 + (RN5T567/RC5T619), LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, LDO8, + LDO9, LDO10, LDORTC1 and LDORTC2. + LDO7-10 are specific to RC5T619. The common bindings for each individual regulator can be found in: Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Bindings/mfd/samsung,exynos5433-lpass.txt b/Bindings/mfd/samsung,exynos5433-lpass.txt new file mode 100644 index 000000000000..c110e118b79f --- /dev/null +++ b/Bindings/mfd/samsung,exynos5433-lpass.txt @@ -0,0 +1,70 @@ +Samsung Exynos SoC Low Power Audio Subsystem (LPASS) + +Required properties: + + - compatible : "samsung,exynos5433-lpass" + - reg : should contain the LPASS top SFR region location + and size + - samsung,pmu-syscon : the phandle to the Power Management Unit node + - #address-cells : should be 1 + - #size-cells : should be 1 + - ranges : must be present + +Each IP block of the Low Power Audio Subsystem should be specified as +an optional sub-node. For "samsung,exynos5433-lpass" compatible this includes: +UART, SLIMBUS, PCM, I2S, DMAC, Timers 0...4, VIC, WDT 0...1 devices. + +Bindings of the sub-nodes are described in: + ../serial/samsung_uart.txt + ../sound/samsung-i2s.txt + ../dma/arm-pl330.txt + + +Example: + +audio-subsystem { + compatible = "samsung,exynos5433-lpass"; + reg = <0x11400000 0x100>, <0x11500000 0x08>; + samsung,pmu-syscon = <&pmu_system_controller>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + adma: adma@11420000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x11420000 0x1000>; + interrupts = <0 73 0>; + clocks = <&cmu_aud CLK_ACLK_DMAC>; + clock-names = "apb_pclk"; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; + }; + + i2s0: i2s0@11440000 { + compatible = "samsung,exynos7-i2s"; + reg = <0x11440000 0x100>; + dmas = <&adma 0 &adma 2>; + dma-names = "tx", "rx"; + interrupts = <0 70 0>; + clocks = <&cmu_aud CLK_PCLK_AUD_I2S>, + <&cmu_aud CLK_SCLK_AUD_I2S>, + <&cmu_aud CLK_SCLK_I2S_BCLK>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_bus>; + status = "disabled"; + }; + + serial_3: serial@11460000 { + compatible = "samsung,exynos5433-uart"; + reg = <0x11460000 0x100>; + interrupts = <0 67 0>; + clocks = <&cmu_aud CLK_PCLK_AUD_UART>, + <&cmu_aud CLK_SCLK_AUD_UART>; + clock-names = "uart", "clk_uart_baud0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart_aud_bus>; + status = "disabled"; + }; + }; diff --git a/Bindings/mfd/stmpe.txt b/Bindings/mfd/stmpe.txt index 3fb68bfefc8b..f9065a5781a2 100644 --- a/Bindings/mfd/stmpe.txt +++ b/Bindings/mfd/stmpe.txt @@ -4,7 +4,7 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - reg : I2C/SPI address of the device Optional properties: diff --git a/Bindings/mfd/tps65086.txt b/Bindings/mfd/tps65086.txt index d3705612a846..9cfa886fe99f 100644 --- a/Bindings/mfd/tps65086.txt +++ b/Bindings/mfd/tps65086.txt @@ -23,7 +23,7 @@ Required properties: defined below. Optional regulator properties: - - ti,regulator-step-size-25mv : This is applicable for buck[1,2,6], set this + - ti,regulator-step-size-25mv : This is applicable for buck[1-6], set this if the regulator is factory set with a 25mv step voltage mapping. - ti,regulator-decay : This is applicable for buck[1-6], set this if diff --git a/Bindings/mfd/twl6040.txt b/Bindings/mfd/twl6040.txt index a41157b5d930..9a98ee7c323d 100644 --- a/Bindings/mfd/twl6040.txt +++ b/Bindings/mfd/twl6040.txt @@ -12,6 +12,7 @@ Required properties: - interrupt-parent: The parent interrupt controller - gpio-controller: - #gpio-cells = <1>: twl6040 provides GPO lines. +- #clock-cells = <0>; twl6040 is a provider of pdmclk which is used by McPDM - twl6040,audpwron-gpio: Power on GPIO line for the twl6040 - vio-supply: Regulator for the twl6040 VIO supply @@ -19,8 +20,8 @@ Required properties: Optional properties, nodes: - enable-active-high: To power on the twl6040 during boot. -- clocks: phandle to the clk32k clock provider -- clock-names: Must be "clk32k" +- clocks: phandle to the clk32k and/or to mclk clock provider +- clock-names: Must be "clk32k" for the 32K clock and "mclk" for the MCLK. Vibra functionality Required properties: |