diff options
Diffstat (limited to 'Bindings/mmc/nvidia,tegra20-sdhci.txt')
| -rw-r--r-- | Bindings/mmc/nvidia,tegra20-sdhci.txt | 72 |
1 files changed, 72 insertions, 0 deletions
diff --git a/Bindings/mmc/nvidia,tegra20-sdhci.txt b/Bindings/mmc/nvidia,tegra20-sdhci.txt index 9bce57862ed6..32b4b4e41923 100644 --- a/Bindings/mmc/nvidia,tegra20-sdhci.txt +++ b/Bindings/mmc/nvidia,tegra20-sdhci.txt @@ -38,3 +38,75 @@ sdhci@c8000200 { power-gpios = <&gpio 155 0>; /* gpio PT3 */ bus-width = <8>; }; + +Optional properties for Tegra210 and Tegra186: +- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage + configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8" + for controllers supporting multiple voltage levels. The order of names + should correspond to the pin configuration states in pinctrl-0 and + pinctrl-1. +- nvidia,only-1-8-v : The presence of this property indicates that the + controller operates at a 1.8 V fixed I/O voltage. +- nvidia,pad-autocal-pull-up-offset-3v3, + nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength + calibration offsets for 3.3 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-1v8, + nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength + calibration offsets for 1.8 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-3v3-timeout, + nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 3.3 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-1v8-timeout, + nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 1.8 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-sdr104, + nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength + calibration offsets for SDR104 mode. +- nvidia,pad-autocal-pull-up-offset-hs400, + nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength + calibration offsets for HS400 mode. +- nvidia,default-tap : Specify the default inbound sampling clock + trimmer value for non-tunable modes. +- nvidia,default-trim : Specify the default outbound clock trimmer + value. +- nvidia,dqs-trim : Specify DQS trim value for HS400 timing + + Notes on the pad calibration pull up and pulldown offset values: + - The property values are drive codes which are programmed into the + PD_OFFSET and PU_OFFSET sections of the + SDHCI_TEGRA_AUTO_CAL_CONFIG register. + - A higher value corresponds to higher drive strength. Please refer + to the reference manual of the SoC for correct values. + - The SDR104 and HS400 timing specific values are used in + corresponding modes if specified. + + Notes on tap and trim values: + - The values are used for compensating trace length differences + by adjusting the sampling point. + - The values are programmed to the Vendor Clock Control Register. + Please refer to the reference manual of the SoC for correct + values. + - The DQS trim values are only used on controllers which support + HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports + HS400. + +Example: +sdhci@700b0000 { + compatible = "nvidia,tegra210-sdhci", "nvidia,tegra124-sdhci"; + reg = <0x0 0x700b0000 0x0 0x200>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_SDMMC1>; + clock-names = "sdhci"; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; + nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; + nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; + nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; + status = "disabled"; +}; |