diff options
Diffstat (limited to 'Bindings/net')
33 files changed, 1233 insertions, 55 deletions
diff --git a/Bindings/net/amlogic,meson-dwmac.yaml b/Bindings/net/amlogic,meson-dwmac.yaml index ee7a65b528cd..d1e2bca3c503 100644 --- a/Bindings/net/amlogic,meson-dwmac.yaml +++ b/Bindings/net/amlogic,meson-dwmac.yaml @@ -58,18 +58,18 @@ allOf: - const: timing-adjustment amlogic,tx-delay-ns: - $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 2, 4, 6] + default: 2 description: - The internal RGMII TX clock delay (provided by this driver) in - nanoseconds. Allowed values are 0ns, 2ns, 4ns, 6ns. - When phy-mode is set to "rgmii" then the TX delay should be - explicitly configured. When not configured a fallback of 2ns is - used. When the phy-mode is set to either "rgmii-id" or "rgmii-txid" - the TX clock delay is already provided by the PHY. In that case - this property should be set to 0ns (which disables the TX clock - delay in the MAC to prevent the clock from going off because both - PHY and MAC are adding a delay). - Any configuration is ignored when the phy-mode is set to "rmii". + The internal RGMII TX clock delay (provided by this driver) + in nanoseconds. When phy-mode is set to "rgmii" then the TX + delay should be explicitly configured. When the phy-mode is + set to either "rgmii-id" or "rgmii-txid" the TX clock delay + is already provided by the PHY. In that case this property + should be set to 0ns (which disables the TX clock delay in + the MAC to prevent the clock from going off because both + PHY and MAC are adding a delay). Any configuration is + ignored when the phy-mode is set to "rmii". amlogic,rx-delay-ns: deprecated: true diff --git a/Bindings/net/bluetooth/amlogic,w155s2-bt.yaml b/Bindings/net/bluetooth/amlogic,w155s2-bt.yaml new file mode 100644 index 000000000000..6fd7557039d2 --- /dev/null +++ b/Bindings/net/bluetooth/amlogic,w155s2-bt.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2024 Amlogic, Inc. All rights reserved +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/bluetooth/amlogic,w155s2-bt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Bluetooth chips + +description: + The W155S2 is an Amlogic Bluetooth and Wi-Fi combo chip. It works on + the standard H4 protocol via a 4-wire UART interface, with baud rates + up to 4 Mbps. + +maintainers: + - Yang Li <yang.li@amlogic.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - amlogic,w265s1-bt + - amlogic,w265p1-bt + - const: amlogic,w155s2-bt + - enum: + - amlogic,w155s2-bt + - amlogic,w265s2-bt + + clocks: + maxItems: 1 + description: clock provided to the controller (32.768KHz) + + enable-gpios: + maxItems: 1 + + vddio-supply: + description: VDD_IO supply regulator handle + + firmware-name: + maxItems: 1 + description: specify the path of firmware bin to load + +required: + - compatible + - clocks + - enable-gpios + - vddio-supply + - firmware-name + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + bluetooth { + compatible = "amlogic,w155s2-bt"; + clocks = <&extclk>; + enable-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + vddio-supply = <&wcn_3v3>; + firmware-name = "amlogic/aml_w155s2_bt_uart.bin"; + }; + diff --git a/Bindings/net/bluetooth/brcm,bluetooth.yaml b/Bindings/net/bluetooth/brcm,bluetooth.yaml new file mode 100644 index 000000000000..3c410cadff23 --- /dev/null +++ b/Bindings/net/bluetooth/brcm,bluetooth.yaml @@ -0,0 +1,163 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/bluetooth/brcm,bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom Bluetooth Chips + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + This binding describes Broadcom UART-attached bluetooth chips. + +properties: + compatible: + oneOf: + - items: + - enum: + - infineon,cyw43439-bt + - const: brcm,bcm4329-bt + - enum: + - brcm,bcm20702a1 + - brcm,bcm4329-bt + - brcm,bcm4330-bt + - brcm,bcm4334-bt + - brcm,bcm43430a0-bt + - brcm,bcm43430a1-bt + - brcm,bcm43438-bt + - brcm,bcm4345c5 + - brcm,bcm43540-bt + - brcm,bcm4335a0 + - brcm,bcm4349-bt + - cypress,cyw4373a0-bt + - infineon,cyw55572-bt + + shutdown-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_REG_ON used to + power on the BT module + + reset-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_RST_N used to + reset the BT module. This should be marked as + GPIO_ACTIVE_LOW. + + device-wakeup-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_WAKE used to + wakeup the controller. This is using the BT_GPIO_0 + pin on the chip when in use. + + host-wakeup-gpios: + maxItems: 1 + deprecated: true + description: GPIO specifier for the line HOST_WAKE used + to wakeup the host processor. This is using he BT_GPIO_1 + pin on the chip when in use. This is deprecated and replaced + by interrupts and "host-wakeup" interrupt-names + + clocks: + minItems: 1 + maxItems: 2 + description: 1 or 2 clocks as defined in clock-names below, + in that order + + clock-names: + description: Names of the 1 to 2 supplied clocks + oneOf: + - const: extclk + deprecated: true + description: Deprecated in favor of txco + + - const: txco + description: > + external reference clock (not a standalone crystal) + + - const: lpo + description: > + external low power 32.768 kHz clock + + - items: + - const: txco + - const: lpo + + vbat-supply: + description: phandle to regulator supply for VBAT + + vddio-supply: + description: phandle to regulator supply for VDDIO + + brcm,bt-pcm-int-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 5 + maxItems: 5 + description: |- + configure PCM parameters via a 5-byte array: + sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S + pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps + pcm-frame-type: short, long + pcm-sync-mode: slave, master + pcm-clock-mode: slave, master + + brcm,requires-autobaud-mode: + type: boolean + description: + Set this property if autobaud mode is required. Autobaud mode is required + if the device's initial baud rate in normal mode is not supported by the + host or if the device requires autobaud mode startup before loading FW. + + interrupts: + items: + - description: Handle to the line HOST_WAKE used to wake + up the host processor. This uses the BT_GPIO_1 pin on + the chip when in use. + + interrupt-names: + items: + - const: host-wakeup + +required: + - compatible + +dependencies: + brcm,requires-autobaud-mode: [ shutdown-gpios ] + +allOf: + - $ref: /schemas/serial/serial-peripheral-props.yaml# + - if: + not: + properties: + compatible: + contains: + enum: + - brcm,bcm20702a1 + - brcm,bcm4329-bt + - brcm,bcm4330-bt + then: + properties: + reset-gpios: false + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + uart { + uart-has-rtscts; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + max-speed = <921600>; + brcm,bt-pcm-int-params = [01 02 00 01 01]; + shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>; + }; + }; diff --git a/Bindings/net/bluetooth/marvell,88w8897.yaml b/Bindings/net/bluetooth/marvell,88w8897.yaml new file mode 100644 index 000000000000..2fc36874deb7 --- /dev/null +++ b/Bindings/net/bluetooth/marvell,88w8897.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/bluetooth/marvell,88w8897.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Bluetooth chips + +description: | + This documents the binding structure and common properties for serial + attached Marvell Bluetooth devices. + +maintainers: + - Rob Herring <robh@kernel.org> + +properties: + compatible: + enum: + - mrvl,88w8897 + - mrvl,88w8997 + + max-speed: true + +required: + - compatible + +allOf: + - $ref: /schemas/serial/serial-peripheral-props.yaml# + - if: + properties: + compatible: + contains: + const: mrvl,88w8997 + then: + properties: + max-speed: true + else: + properties: + max-speed: false + +additionalProperties: false + +examples: + - | + serial { + bluetooth { + compatible = "mrvl,88w8897"; + }; + }; diff --git a/Bindings/net/bluetooth/mediatek,bluetooth.txt b/Bindings/net/bluetooth/mediatek,bluetooth.txt new file mode 100644 index 000000000000..988c72685cbf --- /dev/null +++ b/Bindings/net/bluetooth/mediatek,bluetooth.txt @@ -0,0 +1,80 @@ +MediaTek UART based Bluetooth Devices +================================== + +This device is a serial attached device to UART device and thus it must be a +child node of the serial node with UART. + +Please refer to the following documents for generic properties: + + Documentation/devicetree/bindings/serial/serial.yaml + +Required properties: + +- compatible: Must be + "mediatek,mt7663u-bluetooth": for MT7663U device + "mediatek,mt7668u-bluetooth": for MT7668U device +- vcc-supply: Main voltage regulator + +If the pin controller on the platform can support both pinmux and GPIO +control such as the most of MediaTek platform. Please use below properties. + +- pinctrl-names: Should be "default", "runtime" +- pinctrl-0: Should contain UART RXD low when the device is powered up to + enter proper bootstrap mode. +- pinctrl-1: Should contain UART mode pin ctrl + +Else, the pin controller on the platform only can support pinmux control and +the GPIO control still has to rely on the dedicated GPIO controller such as +a legacy MediaTek SoC, MT7621. Please use the below properties. + +- boot-gpios: GPIO same to the pin as UART RXD and used to keep LOW when + the device is powered up to enter proper bootstrap mode when +- pinctrl-names: Should be "default" +- pinctrl-0: Should contain UART mode pin ctrl + +Optional properties: + +- reset-gpios: GPIO used to reset the device whose initial state keeps low, + if the GPIO is missing, then board-level design should be + guaranteed. +- clocks: Should be the clock specifiers corresponding to the entry in + clock-names property. If the clock is missing, then board-level + design should be guaranteed. +- clock-names: Should contain "osc" entry for the external oscillator. +- current-speed: Current baud rate of the device whose defaults to 921600 + +Example: + + uart1_pins_boot: uart1-default { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_GPIO81>; + output-low; + }; + }; + + uart1_pins_runtime: uart1-runtime { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>, + <MT7623_PIN_82_UTXD1_FUNC_UTXD1>; + }; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt7623-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x400>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_UART1_SEL>, + <&pericfg CLK_PERI_UART1>; + clock-names = "baud", "bus"; + + bluetooth { + compatible = "mediatek,mt7663u-bluetooth"; + vcc-supply = <®_5v>; + reset-gpios = <&pio 24 GPIO_ACTIVE_LOW>; + pinctrl-names = "default", "runtime"; + pinctrl-0 = <&uart1_pins_boot>; + pinctrl-1 = <&uart1_pins_runtime>; + current-speed = <921600>; + }; + }; diff --git a/Bindings/net/bluetooth/nokia,h4p-bluetooth.txt b/Bindings/net/bluetooth/nokia,h4p-bluetooth.txt new file mode 100644 index 000000000000..42be7dc9a70b --- /dev/null +++ b/Bindings/net/bluetooth/nokia,h4p-bluetooth.txt @@ -0,0 +1,51 @@ +Nokia Bluetooth Chips +--------------------- + +Nokia phones often come with UART connected bluetooth chips from different +vendors and modified device API. Those devices speak a protocol named H4+ +(also known as h4p) by Nokia, which is similar to the H4 protocol from the +Bluetooth standard. In addition to the H4 protocol it specifies two more +UART status lines for wakeup of UART transceivers to improve power management +and a few new packet types used to negotiate uart speed. + +Required properties: + + - compatible: should contain "nokia,h4p-bluetooth" as well as one of the following: + * "brcm,bcm2048-nokia" + * "ti,wl1271-bluetooth-nokia" + - reset-gpios: GPIO specifier, used to reset the BT module (active low) + - bluetooth-wakeup-gpios: GPIO specifier, used to wakeup the BT module (active high) + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor (active high) + - clock-names: should be "sysclk" + - clocks: should contain a clock specifier for every name in clock-names + +Optional properties: + + - None + +Example: + +/ { + /* controlled (enabled/disabled) directly by BT module */ + bluetooth_clk: vctcxo { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + + bluetooth { + compatible = "ti,wl1271-bluetooth-nokia", "nokia,h4p-bluetooth"; + + reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; /* gpio26 */ + host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */ + bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* gpio37 */ + + clocks = <&bluetooth_clk>; + clock-names = "sysclk"; + }; +}; diff --git a/Bindings/net/bluetooth/qualcomm-bluetooth.yaml b/Bindings/net/bluetooth/qualcomm-bluetooth.yaml index 68c5ed111417..7bb68311c609 100644 --- a/Bindings/net/bluetooth/qualcomm-bluetooth.yaml +++ b/Bindings/net/bluetooth/qualcomm-bluetooth.yaml @@ -72,7 +72,7 @@ properties: description: VDD_RFA_CMN supply regulator handle vddrfa0p8-supply: - description: VDD_RFA_0P8 suppply regulator handle + description: VDD_RFA_0P8 supply regulator handle vddrfa1p7-supply: description: VDD_RFA_1P7 supply regulator handle @@ -98,8 +98,7 @@ properties: vddwlmx-supply: description: VDD_WLMX supply regulator handle - max-speed: - description: see Documentation/devicetree/bindings/serial/serial.yaml + max-speed: true firmware-name: description: specify the name of nvm firmware to load @@ -118,6 +117,7 @@ additionalProperties: false allOf: - $ref: bluetooth-controller.yaml# + - $ref: /schemas/serial/serial-peripheral-props.yaml# - if: properties: compatible: @@ -172,14 +172,14 @@ allOf: - qcom,wcn6855-bt then: required: - - enable-gpios - - swctrl-gpios - - vddio-supply - - vddbtcxmx-supply - vddrfacmn-supply + - vddaon-supply + - vddwlcx-supply + - vddwlmx-supply + - vddbtcmx-supply - vddrfa0p8-supply - vddrfa1p2-supply - - vddrfa1p7-supply + - vddrfa1p8-supply - if: properties: compatible: diff --git a/Bindings/net/bluetooth/realtek,bluetooth.yaml b/Bindings/net/bluetooth/realtek,bluetooth.yaml new file mode 100644 index 000000000000..7d567122bac9 --- /dev/null +++ b/Bindings/net/bluetooth/realtek,bluetooth.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/bluetooth/realtek,bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RTL8723BS/RTL8723CS/RTL8821CS/RTL8822CS Bluetooth + +maintainers: + - Vasily Khoruzhick <anarsoul@gmail.com> + - Alistair Francis <alistair@alistair23.me> + +description: + RTL8723BS/RTL8723CS/RTL8821CS/RTL8822CS is a WiFi + BT chip. WiFi part + is connected over SDIO, while BT is connected over serial. It speaks + H5 protocol with few extra commands to upload firmware and change + module speed. + +properties: + compatible: + oneOf: + - enum: + - realtek,rtl8723bs-bt + - realtek,rtl8723cs-bt + - realtek,rtl8723ds-bt + - realtek,rtl8822cs-bt + - items: + - enum: + - realtek,rtl8821cs-bt + - const: realtek,rtl8723bs-bt + + device-wake-gpios: + maxItems: 1 + description: GPIO specifier, used to wakeup the BT module + + enable-gpios: + maxItems: 1 + description: GPIO specifier, used to enable the BT module + + host-wake-gpios: + maxItems: 1 + description: GPIO specifier, used to wakeup the host processor + + max-speed: true + +required: + - compatible + +allOf: + - $ref: /schemas/serial/serial-peripheral-props.yaml# + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + uart-has-rtscts; + + bluetooth { + compatible = "realtek,rtl8723bs-bt"; + device-wake-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */ + host-wake-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + }; + }; diff --git a/Bindings/net/bluetooth/ti,bluetooth.yaml b/Bindings/net/bluetooth/ti,bluetooth.yaml new file mode 100644 index 000000000000..290abc22e18a --- /dev/null +++ b/Bindings/net/bluetooth/ti,bluetooth.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/bluetooth/ti,bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments Bluetooth Chips + +maintainers: + - David Lechner <david@lechnology.com> + +description: | + This documents the binding structure and common properties for serial + attached TI Bluetooth devices. The following chips are included in this + binding: + + * TI CC256x Bluetooth devices + * TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices + + TI WiLink devices have a UART interface for providing Bluetooth, FM radio, + and GPS over what's called "shared transport". The shared transport is + standard BT HCI protocol with additional channels for the other functions. + + TI WiLink devices also have a separate WiFi interface as described in + wireless/ti,wlcore.yaml. + + This bindings follows the UART slave device binding in ../serial/serial.yaml. + +properties: + compatible: + enum: + - ti,cc2560 + - ti,wl1271-st + - ti,wl1273-st + - ti,wl1281-st + - ti,wl1283-st + - ti,wl1285-st + - ti,wl1801-st + - ti,wl1805-st + - ti,wl1807-st + - ti,wl1831-st + - ti,wl1835-st + - ti,wl1837-st + + enable-gpios: + maxItems: 1 + + vio-supply: + description: Vio input supply (1.8V) + + vbat-supply: + description: Vbat input supply (2.9-4.8V) + + clocks: + maxItems: 1 + + clock-names: + items: + - const: ext_clock + + max-speed: + default: 3000000 + + nvmem-cells: + maxItems: 1 + description: + Nvmem data cell that contains a 6 byte BD address with the most + significant byte first (big-endian). + + nvmem-cell-names: + items: + - const: bd-address + +required: + - compatible + +allOf: + - $ref: /schemas/serial/serial-peripheral-props.yaml# + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + serial { + bluetooth { + compatible = "ti,wl1835-st"; + enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + clocks = <&clk32k_wl18xx>; + clock-names = "ext_clock"; + nvmem-cells = <&bd_address>; + nvmem-cell-names = "bd-address"; + }; + }; diff --git a/Bindings/net/brcm,unimac-mdio.yaml b/Bindings/net/brcm,unimac-mdio.yaml index 23dfe0838dca..63bee5b542f5 100644 --- a/Bindings/net/brcm,unimac-mdio.yaml +++ b/Bindings/net/brcm,unimac-mdio.yaml @@ -26,6 +26,7 @@ properties: - brcm,asp-v2.1-mdio - brcm,asp-v2.2-mdio - brcm,unimac-mdio + - brcm,bcm6846-mdio reg: minItems: 1 diff --git a/Bindings/net/can/fsl,flexcan.yaml b/Bindings/net/can/fsl,flexcan.yaml index f197d9b516bb..97dd1a7c5ed2 100644 --- a/Bindings/net/can/fsl,flexcan.yaml +++ b/Bindings/net/can/fsl,flexcan.yaml @@ -17,6 +17,7 @@ properties: compatible: oneOf: - enum: + - fsl,imx95-flexcan - fsl,imx93-flexcan - fsl,imx8qm-flexcan - fsl,imx8mp-flexcan @@ -39,9 +40,6 @@ properties: - fsl,imx6sx-flexcan - const: fsl,imx6q-flexcan - items: - - const: fsl,imx95-flexcan - - const: fsl,imx93-flexcan - - items: - enum: - fsl,ls1028ar1-flexcan - const: fsl,lx2160ar1-flexcan @@ -80,6 +78,10 @@ properties: node then controller is assumed to be little endian. If this property is present then controller is assumed to be big endian. + can-transceiver: + $ref: can-transceiver.yaml# + unevaluatedProperties: false + fsl,stop-mode: description: | Register bits of stop mode control. diff --git a/Bindings/net/can/microchip,mcp2510.yaml b/Bindings/net/can/microchip,mcp2510.yaml new file mode 100644 index 000000000000..db446dde6842 --- /dev/null +++ b/Bindings/net/can/microchip,mcp2510.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/can/microchip,mcp2510.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip MCP251X stand-alone CAN controller + +maintainers: + - Marc Kleine-Budde <mkl@pengutronix.de> + +properties: + compatible: + enum: + - microchip,mcp2510 + - microchip,mcp2515 + - microchip,mcp25625 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + interrupts: + maxItems: 1 + + vdd-supply: + description: Regulator that powers the CAN controller. + + xceiver-supply: + description: Regulator that powers the CAN transceiver. + + gpio-controller: true + + "#gpio-cells": + const: 2 + +required: + - compatible + - reg + - clocks + - interrupts + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + can@1 { + compatible = "microchip,mcp2515"; + reg = <1>; + clocks = <&clk24m>; + interrupt-parent = <&gpio4>; + interrupts = <13 IRQ_TYPE_LEVEL_LOW>; + vdd-supply = <®5v0>; + xceiver-supply = <®5v0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + diff --git a/Bindings/net/can/renesas,rcar-canfd.yaml b/Bindings/net/can/renesas,rcar-canfd.yaml index d3f45d29fa0a..7c5ac5d2e880 100644 --- a/Bindings/net/can/renesas,rcar-canfd.yaml +++ b/Bindings/net/can/renesas,rcar-canfd.yaml @@ -32,6 +32,7 @@ properties: - enum: - renesas,r8a779a0-canfd # R-Car V3U - renesas,r8a779g0-canfd # R-Car V4H + - renesas,r8a779h0-canfd # R-Car V4M - const: renesas,rcar-gen4-canfd # R-Car Gen4 - items: @@ -163,14 +164,23 @@ allOf: maxItems: 1 - if: - not: - properties: - compatible: - contains: - const: renesas,rcar-gen4-canfd + properties: + compatible: + contains: + const: renesas,r8a779h0-canfd then: patternProperties: - "^channel[2-7]$": false + "^channel[5-7]$": false + else: + if: + not: + properties: + compatible: + contains: + const: renesas,rcar-gen4-canfd + then: + patternProperties: + "^channel[2-7]$": false unevaluatedProperties: false diff --git a/Bindings/net/can/rockchip,rk3568v2-canfd.yaml b/Bindings/net/can/rockchip,rk3568v2-canfd.yaml new file mode 100644 index 000000000000..a077c0330013 --- /dev/null +++ b/Bindings/net/can/rockchip,rk3568v2-canfd.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/can/rockchip,rk3568v2-canfd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: + Rockchip CAN-FD controller + +maintainers: + - Marc Kleine-Budde <mkl@pengutronix.de> + +allOf: + - $ref: can-controller.yaml# + +properties: + compatible: + oneOf: + - const: rockchip,rk3568v2-canfd + - items: + - const: rockchip,rk3568v3-canfd + - const: rockchip,rk3568v2-canfd + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: baud + - const: pclk + + resets: + maxItems: 2 + + reset-names: + items: + - const: core + - const: apb + +required: + - compatible + - reg + - interrupts + - clocks + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3568-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + can@fe570000 { + compatible = "rockchip,rk3568v2-canfd"; + reg = <0x0 0xfe570000 0x0 0x1000>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru CLK_CAN0>, <&cru PCLK_CAN0>; + clock-names = "baud", "pclk"; + resets = <&cru SRST_CAN0>, <&cru SRST_P_CAN0>; + reset-names = "core", "apb"; + }; + }; diff --git a/Bindings/net/cirrus,ep9301-eth.yaml b/Bindings/net/cirrus,ep9301-eth.yaml new file mode 100644 index 000000000000..ad0915307095 --- /dev/null +++ b/Bindings/net/cirrus,ep9301-eth.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/cirrus,ep9301-eth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: EP93xx SoC Ethernet Controller + +maintainers: + - Alexander Sverdlin <alexander.sverdlin@gmail.com> + - Nikita Shubin <nikita.shubin@maquefel.me> + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + oneOf: + - const: cirrus,ep9301-eth + - items: + - enum: + - cirrus,ep9302-eth + - cirrus,ep9307-eth + - cirrus,ep9312-eth + - cirrus,ep9315-eth + - const: cirrus,ep9301-eth + + reg: + items: + - description: The physical base address and size of IO range + + interrupts: + items: + - description: Combined signal for various interrupt events + + phy-handle: true + + mdio: + $ref: mdio.yaml# + unevaluatedProperties: false + description: optional node for embedded MDIO controller + +required: + - compatible + - reg + - interrupts + - phy-handle + +additionalProperties: false + +examples: + - | + ethernet@80010000 { + compatible = "cirrus,ep9301-eth"; + reg = <0x80010000 0x10000>; + interrupt-parent = <&vic1>; + interrupts = <7>; + phy-handle = <&phy0>; + }; diff --git a/Bindings/net/dsa/mediatek,mt7530.yaml b/Bindings/net/dsa/mediatek,mt7530.yaml index 7e405ad96eb2..ea979bcae1d6 100644 --- a/Bindings/net/dsa/mediatek,mt7530.yaml +++ b/Bindings/net/dsa/mediatek,mt7530.yaml @@ -92,6 +92,10 @@ properties: Built-in switch of the MT7988 SoC const: mediatek,mt7988-switch + - description: + Built-in switch of the Airoha EN7581 SoC + const: airoha,en7581-switch + reg: maxItems: 1 @@ -284,7 +288,9 @@ allOf: - if: properties: compatible: - const: mediatek,mt7988-switch + enum: + - mediatek,mt7988-switch + - airoha,en7581-switch then: $ref: "#/$defs/mt7530-dsa-port" properties: diff --git a/Bindings/net/dsa/microchip,ksz.yaml b/Bindings/net/dsa/microchip,ksz.yaml index 52acc15ebcbf..30c0c3e6f37a 100644 --- a/Bindings/net/dsa/microchip,ksz.yaml +++ b/Bindings/net/dsa/microchip,ksz.yaml @@ -22,7 +22,9 @@ properties: - microchip,ksz8794 - microchip,ksz8795 - microchip,ksz8863 + - microchip,ksz8864 # 4-port version of KSZ8895 family switch - microchip,ksz8873 + - microchip,ksz8895 # 5-port version of KSZ8895 family switch - microchip,ksz9477 - microchip,ksz9897 - microchip,ksz9896 @@ -51,6 +53,11 @@ properties: Set if the output SYNCLKO clock should be disabled. Do not mix with microchip,synclko-125. + microchip,pme-active-high: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates if the PME pin polarity is active-high. + microchip,io-drive-strength-microamp: description: IO Pad Drive Strength diff --git a/Bindings/net/dsa/vitesse,vsc73xx.yaml b/Bindings/net/dsa/vitesse,vsc73xx.yaml index b99d7a694b70..51cf574249be 100644 --- a/Bindings/net/dsa/vitesse,vsc73xx.yaml +++ b/Bindings/net/dsa/vitesse,vsc73xx.yaml @@ -52,6 +52,25 @@ properties: allOf: - $ref: dsa.yaml#/$defs/ethernet-ports +patternProperties: + "^(ethernet-)?ports$": + additionalProperties: true + patternProperties: + "^(ethernet-)?port@6$": + allOf: + - if: + properties: + phy-mode: + contains: + enum: + - rgmii + then: + properties: + rx-internal-delay-ps: + $ref: "#/$defs/internal-delay-ps" + tx-internal-delay-ps: + $ref: "#/$defs/internal-delay-ps" + # This checks if reg is a chipselect so the device is on an SPI # bus, the if-clause will fail if reg is a tuple such as for a # platform device. @@ -67,6 +86,15 @@ required: - compatible - reg +$defs: + internal-delay-ps: + description: + Disable tunable delay lines using 0 ps, or enable them and select + the phase between 1400 ps and 2000 ps in increments of 300 ps. + default: 2000 + enum: + [0, 1400, 1700, 2000] + unevaluatedProperties: false examples: @@ -108,6 +136,8 @@ examples: reg = <6>; ethernet = <&gmac1>; phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; fixed-link { speed = <1000>; full-duplex; @@ -150,6 +180,8 @@ examples: ethernet-port@6 { reg = <6>; ethernet = <&enet0>; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; phy-mode = "rgmii"; fixed-link { speed = <1000>; diff --git a/Bindings/net/fsl,cpm-enet.yaml b/Bindings/net/fsl,cpm-enet.yaml new file mode 100644 index 000000000000..da836477e8ba --- /dev/null +++ b/Bindings/net/fsl,cpm-enet.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/fsl,cpm-enet.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Network for cpm enet + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +properties: + compatible: + oneOf: + - enum: + - fsl,cpm1-scc-enet + - fsl,cpm2-scc-enet + - fsl,cpm1-fec-enet + - fsl,cpm2-fcc-enet + - fsl,qe-enet + - items: + - enum: + - fsl,mpc8272-fcc-enet + - const: fsl,cpm2-fcc-enet + + reg: + minItems: 1 + maxItems: 3 + + interrupts: + maxItems: 1 + + fsl,cpm-command: + $ref: /schemas/types.yaml#/definitions/uint32 + description: cpm command + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: ethernet-controller.yaml + +unevaluatedProperties: false + +examples: + - | + ethernet@11300 { + compatible = "fsl,mpc8272-fcc-enet", + "fsl,cpm2-fcc-enet"; + reg = <0x11300 0x20 0x8400 0x100 0x11390 1>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <20 8>; + interrupt-parent = <&pic>; + phy-handle = <&phy0>; + fsl,cpm-command = <0x12000300>; + }; + diff --git a/Bindings/net/fsl,cpm-mdio.yaml b/Bindings/net/fsl,cpm-mdio.yaml new file mode 100644 index 000000000000..b1791a3c490e --- /dev/null +++ b/Bindings/net/fsl,cpm-mdio.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/fsl,cpm-mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale CPM MDIO Device + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +properties: + compatible: + oneOf: + - enum: + - fsl,pq1-fec-mdio + - fsl,cpm2-mdio-bitbang + - items: + - const: fsl,mpc8272ads-mdio-bitbang + - const: fsl,mpc8272-mdio-bitbang + - const: fsl,cpm2-mdio-bitbang + + reg: + maxItems: 1 + + fsl,mdio-pin: + $ref: /schemas/types.yaml#/definitions/uint32 + description: pin of port C controlling mdio data + + fsl,mdc-pin: + $ref: /schemas/types.yaml#/definitions/uint32 + description: pin of port C controlling mdio clock + +required: + - compatible + - reg + +allOf: + - $ref: mdio.yaml# + +unevaluatedProperties: false + +examples: + - | + mdio@10d40 { + compatible = "fsl,mpc8272ads-mdio-bitbang", + "fsl,mpc8272-mdio-bitbang", + "fsl,cpm2-mdio-bitbang"; + reg = <0x10d40 0x14>; + #address-cells = <1>; + #size-cells = <0>; + fsl,mdio-pin = <12>; + fsl,mdc-pin = <13>; + }; + diff --git a/Bindings/net/fsl,qoriq-mc-dpmac.yaml b/Bindings/net/fsl,qoriq-mc-dpmac.yaml index 42f9843d1868..be8a2163b73e 100644 --- a/Bindings/net/fsl,qoriq-mc-dpmac.yaml +++ b/Bindings/net/fsl,qoriq-mc-dpmac.yaml @@ -24,20 +24,12 @@ properties: maxItems: 1 description: The DPMAC number - phy-handle: true - - phy-connection-type: true - - phy-mode: true - pcs-handle: maxItems: 1 description: A reference to a node representing a PCS PHY device found on the internal MDIO bus. - managed: true - phys: description: A reference to the SerDes lane(s) maxItems: 1 @@ -45,7 +37,7 @@ properties: required: - reg -additionalProperties: false +unevaluatedProperties: false examples: - | diff --git a/Bindings/net/maxim,ds26522.yaml b/Bindings/net/maxim,ds26522.yaml new file mode 100644 index 000000000000..6c97eda217e8 --- /dev/null +++ b/Bindings/net/maxim,ds26522.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/maxim,ds26522.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim (Dallas) DS26522 Dual T1/E1/J1 Transceiver + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +properties: + compatible: + items: + - const: maxim,ds26522 + + reg: + maxItems: 1 + +required: + - compatible + - reg + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + transceiver@1 { + compatible = "maxim,ds26522"; + reg = <1>; + spi-max-frequency = <2000000>; /* input clock */ + }; + }; diff --git a/Bindings/net/mdio.yaml b/Bindings/net/mdio.yaml index a266ade918ca..bed3987a8fbf 100644 --- a/Bindings/net/mdio.yaml +++ b/Bindings/net/mdio.yaml @@ -19,7 +19,7 @@ description: properties: $nodename: - pattern: "^mdio(@.*)?" + pattern: '^mdio(-(bus|external))?(@.+|-([0-9]+))?$' "#address-cells": const: 1 diff --git a/Bindings/net/mediatek,net.yaml b/Bindings/net/mediatek,net.yaml index 686b5c2fae40..9e02fd80af83 100644 --- a/Bindings/net/mediatek,net.yaml +++ b/Bindings/net/mediatek,net.yaml @@ -30,8 +30,13 @@ properties: reg: maxItems: 1 - clocks: true - clock-names: true + clocks: + minItems: 2 + maxItems: 24 + + clock-names: + minItems: 2 + maxItems: 24 interrupts: minItems: 1 @@ -127,6 +132,7 @@ allOf: then: properties: interrupts: + minItems: 3 maxItems: 3 clocks: @@ -183,6 +189,7 @@ allOf: then: properties: interrupts: + minItems: 3 maxItems: 3 clocks: @@ -222,6 +229,7 @@ allOf: then: properties: interrupts: + minItems: 3 maxItems: 3 clocks: diff --git a/Bindings/net/microchip,lan8650.yaml b/Bindings/net/microchip,lan8650.yaml new file mode 100644 index 000000000000..61e11d4a07c4 --- /dev/null +++ b/Bindings/net/microchip,lan8650.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/microchip,lan8650.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip LAN8650/1 10BASE-T1S MACPHY Ethernet Controllers + +maintainers: + - Parthiban Veerasooran <parthiban.veerasooran@microchip.com> + +description: + The LAN8650/1 combines a Media Access Controller (MAC) and an Ethernet + PHY to enable 10BASE‑T1S networks. The Ethernet Media Access Controller + (MAC) module implements a 10 Mbps half duplex Ethernet MAC, compatible + with the IEEE 802.3 standard and a 10BASE-T1S physical layer transceiver + integrated into the LAN8650/1. The communication between the Host and + the MAC-PHY is specified in the OPEN Alliance 10BASE-T1x MACPHY Serial + Interface (TC6). + +allOf: + - $ref: /schemas/net/ethernet-controller.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + oneOf: + - const: microchip,lan8650 + - items: + - const: microchip,lan8651 + - const: microchip,lan8650 + + reg: + maxItems: 1 + + interrupts: + description: + Interrupt from MAC-PHY asserted in the event of Receive Chunks + Available, Transmit Chunk Credits Available and Extended Status + Event. + maxItems: 1 + + spi-max-frequency: + minimum: 15000000 + maximum: 25000000 + +required: + - compatible + - reg + - interrupts + - spi-max-frequency + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + ethernet@0 { + compatible = "microchip,lan8651", "microchip,lan8650"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <ð0_pins>; + interrupt-parent = <&gpio>; + interrupts = <6 IRQ_TYPE_EDGE_FALLING>; + local-mac-address = [04 05 06 01 02 03]; + spi-max-frequency = <15000000>; + }; + }; diff --git a/Bindings/net/pse-pd/ti,tps23881.yaml b/Bindings/net/pse-pd/ti,tps23881.yaml index 6992d56832bf..d08abcb01211 100644 --- a/Bindings/net/pse-pd/ti,tps23881.yaml +++ b/Bindings/net/pse-pd/ti,tps23881.yaml @@ -23,6 +23,9 @@ properties: '#pse-cells': const: 1 + reset-gpios: + maxItems: 1 + channels: description: each set of 8 ports can be assigned to one physical channels or two for PoE4. This parameter describes the configuration diff --git a/Bindings/net/renesas,etheravb.yaml b/Bindings/net/renesas,etheravb.yaml index 21a92f179093..1e00ef5b3acd 100644 --- a/Bindings/net/renesas,etheravb.yaml +++ b/Bindings/net/renesas,etheravb.yaml @@ -62,15 +62,27 @@ properties: - renesas,r9a08g045-gbeth # RZ/G3S - const: renesas,rzg2l-gbeth # RZ/{G2L,G2UL,V2L} family - reg: true + reg: + minItems: 1 + items: + - description: MAC register block + - description: Stream buffer - interrupts: true + interrupts: + minItems: 1 + maxItems: 29 - interrupt-names: true + interrupt-names: + minItems: 1 + maxItems: 29 - clocks: true + clocks: + minItems: 1 + maxItems: 3 - clock-names: true + clock-names: + minItems: 1 + maxItems: 3 iommus: maxItems: 1 @@ -150,14 +162,11 @@ allOf: then: properties: reg: - items: - - description: MAC register block - - description: Stream buffer + minItems: 2 else: properties: reg: - items: - - description: MAC register block + maxItems: 1 - if: properties: diff --git a/Bindings/net/rockchip-dwmac.yaml b/Bindings/net/rockchip-dwmac.yaml index 6bbe96e35250..f8a576611d6c 100644 --- a/Bindings/net/rockchip-dwmac.yaml +++ b/Bindings/net/rockchip-dwmac.yaml @@ -25,6 +25,7 @@ select: - rockchip,rk3368-gmac - rockchip,rk3399-gmac - rockchip,rk3568-gmac + - rockchip,rk3576-gmac - rockchip,rk3588-gmac - rockchip,rv1108-gmac - rockchip,rv1126-gmac @@ -52,6 +53,7 @@ properties: - items: - enum: - rockchip,rk3568-gmac + - rockchip,rk3576-gmac - rockchip,rk3588-gmac - rockchip,rv1126-gmac - const: snps,dwmac-4.20a diff --git a/Bindings/net/snps,dwmac.yaml b/Bindings/net/snps,dwmac.yaml index 3eb65e63fdae..4e2ba1bf788c 100644 --- a/Bindings/net/snps,dwmac.yaml +++ b/Bindings/net/snps,dwmac.yaml @@ -80,6 +80,7 @@ properties: - rockchip,rk3328-gmac - rockchip,rk3366-gmac - rockchip,rk3368-gmac + - rockchip,rk3576-gmac - rockchip,rk3588-gmac - rockchip,rk3399-gmac - rockchip,rv1108-gmac diff --git a/Bindings/net/socionext,uniphier-ave4.yaml b/Bindings/net/socionext,uniphier-ave4.yaml index b0ebcef6801c..4eb63b303cff 100644 --- a/Bindings/net/socionext,uniphier-ave4.yaml +++ b/Bindings/net/socionext,uniphier-ave4.yaml @@ -41,13 +41,17 @@ properties: minItems: 1 maxItems: 4 - clock-names: true + clock-names: + minItems: 1 + maxItems: 4 resets: minItems: 1 maxItems: 2 - reset-names: true + reset-names: + minItems: 1 + maxItems: 2 socionext,syscon-phy-mode: $ref: /schemas/types.yaml#/definitions/phandle-array diff --git a/Bindings/net/ti,cc1352p7.yaml b/Bindings/net/ti,cc1352p7.yaml index 3dde10de4630..4f4253441547 100644 --- a/Bindings/net/ti,cc1352p7.yaml +++ b/Bindings/net/ti,cc1352p7.yaml @@ -29,6 +29,12 @@ properties: reset-gpios: maxItems: 1 + bootloader-backdoor-gpios: + maxItems: 1 + description: | + gpios to enable bootloader backdoor in cc1352p7 bootloader to allow + flashing new firmware. + vdds-supply: true required: @@ -46,6 +52,7 @@ examples: clocks = <&sclk_hf 0>, <&sclk_lf 25>; clock-names = "sclk_hf", "sclk_lf"; reset-gpios = <&pio 35 GPIO_ACTIVE_LOW>; + bootloader-backdoor-gpios = <&pio 36 GPIO_ACTIVE_LOW>; vdds-supply = <&vdds>; }; }; diff --git a/Bindings/net/wireless/marvell,sd8787.yaml b/Bindings/net/wireless/marvell,sd8787.yaml new file mode 100644 index 000000000000..1715b22e0dcf --- /dev/null +++ b/Bindings/net/wireless/marvell,sd8787.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/marvell,sd8787.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell 8787/8897/8978/8997 (sd8787/sd8897/sd8978/sd8997/pcie8997) SDIO/PCIE devices + +maintainers: + - Brian Norris <briannorris@chromium.org> + - Frank Li <Frank.Li@nxp.com> + +description: + This node provides properties for describing the Marvell SDIO/PCIE wireless device. + The node is expected to be specified as a child node to the SDIO/PCIE controller that + connects the device to the system. + +properties: + compatible: + enum: + - marvell,sd8787 + - marvell,sd8897 + - marvell,sd8978 + - marvell,sd8997 + - nxp,iw416 + - pci11ab,2b42 + - pci1b4b,2b42 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + wakeup-source: true + + marvell,caldata-txpwrlimit-2g: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: Calibration data for the 2GHz band. + maxItems: 566 + + marvell,caldata-txpwrlimit-5g-sub0: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: Calibration data for sub-band 0 in the 5GHz band. + maxItems: 502 + + marvell,caldata-txpwrlimit-5g-sub1: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: Calibration data for sub-band 1 in the 5GHz band. + maxItems: 688 + + marvell,caldata-txpwrlimit-5g-sub2: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: Calibration data for sub-band 2 in the 5GHz band. + maxItems: 750 + + marvell,caldata-txpwrlimit-5g-sub3: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: Calibration data for sub-band 3 in the 5GHz band. + maxItems: 502 + + marvell,wakeup-pin: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Provides the pin number for the wakeup pin from the device's point of + view. The wakeup pin is used for the device to wake the host system + from sleep. This property is only necessary if the wakeup pin is + wired in a non-standard way, such that the default pin assignments + are invalid. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + mmc { + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "marvell,sd8897"; + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + marvell,wakeup-pin = <3>; + }; + }; + diff --git a/Bindings/net/xlnx,axi-ethernet.yaml b/Bindings/net/xlnx,axi-ethernet.yaml index bbe89ea9590c..fb02e579463c 100644 --- a/Bindings/net/xlnx,axi-ethernet.yaml +++ b/Bindings/net/xlnx,axi-ethernet.yaml @@ -34,6 +34,7 @@ properties: and length of the AXI DMA controller IO space, unless axistream-connected is specified, in which case the reg attribute of the node referenced by it is used. + minItems: 1 maxItems: 2 interrupts: @@ -60,7 +61,7 @@ properties: - gmii - rgmii - sgmii - - 1000BaseX + - 1000base-x xlnx,phy-type: description: @@ -181,7 +182,7 @@ examples: clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk"; clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>; phy-mode = "mii"; - reg = <0x00 0x40000000 0x00 0x40000>; + reg = <0x40000000 0x40000>; xlnx,rxcsum = <0x2>; xlnx,rxmem = <0x800>; xlnx,txcsum = <0x2>; |