diff options
Diffstat (limited to 'Bindings/phy/ti-phy.txt')
| -rw-r--r-- | Bindings/phy/ti-phy.txt | 36 |
1 files changed, 33 insertions, 3 deletions
diff --git a/Bindings/phy/ti-phy.txt b/Bindings/phy/ti-phy.txt index 305e3df3d9b1..a3b394587874 100644 --- a/Bindings/phy/ti-phy.txt +++ b/Bindings/phy/ti-phy.txt @@ -31,6 +31,8 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" + Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY + in DRA7x - reg : Address and length of the register set for the device. - #phy-cells: determine the number of cells that should be given in the phandle while referencing this phy. @@ -40,10 +42,14 @@ Required properties: * "wkupclk" - wakeup clock. * "refclk" - reference clock (optional). -Optional properties: +Deprecated properties: - ctrl-module : phandle of the control module used by PHY driver to power on the PHY. +Recommended properies: +- syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. + This is usually a subnode of ocp2scp to which it is connected. usb2phy@4a0ad080 { @@ -77,11 +83,22 @@ Required properties: * "div-clk" - apll clock Optional properties: - - ctrl-module : phandle of the control module used by PHY driver to power on - the PHY. - id: If there are multiple instance of the same type, in order to differentiate between each instance "id" can be used (e.g., multi-lane PCIe PHY). If "id" is not provided, it is set to default value of '1'. + - syscon-pllreset: Handle to system control region that contains the + CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0 + register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy. + - syscon-pcs : phandle/offset pair. Phandle to the system control module and the + register offset to write the PCS delay value. + +Deprecated properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +Recommended properies: + - syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. This is usually a subnode of ocp2scp to which it is connected. @@ -100,3 +117,16 @@ usb3phy@4a084400 { "sysclk", "refclk"; }; + +sata_phy: phy@4A096000 { + compatible = "ti,phy-pipe3-sata"; + reg = <0x4A096000 0x80>, /* phy_rx */ + <0x4A096400 0x64>, /* phy_tx */ + <0x4A096800 0x40>; /* pll_ctrl */ + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_sata>; + clocks = <&sys_clkin1>, <&sata_ref_clk>; + clock-names = "sysclk", "refclk"; + syscon-pllreset = <&scm_conf 0x3fc>; + #phy-cells = <0>; +}; |