diff options
Diffstat (limited to 'Bindings/pinctrl')
26 files changed, 1050 insertions, 52 deletions
diff --git a/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 69617220c5d6..de1378b4efad 100644 --- a/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -23,10 +23,25 @@ Required properties: "allwinner,sun8i-h3-pinctrl" "allwinner,sun8i-h3-r-pinctrl" "allwinner,sun50i-a64-pinctrl" + "nextthing,gr8-pinctrl" - reg: Should contain the register physical address and length for the pin controller. +- clocks: phandle to the clocks feeding the pin controller: + - "apb": the gated APB parent clock + - "hosc": the high frequency oscillator in the system + - "losc": the low frequency oscillator in the system + +Note: For backward compatibility reasons, the hosc and losc clocks are only +required if you need to use the optional input-debounce property. Any new +device tree should set them. + +Optional properties: + - input-debounce: Array of debouncing periods in microseconds. One period per + irq bank found in the controller. 0 if no setup required. + + Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. @@ -36,6 +51,22 @@ pins it needs, and how they should be configured, with regard to muxer configuration, drive strength and pullups. If one of these options is not set, its actual value will be unspecified. +This driver supports the generic pin multiplexing and configuration +bindings. For details on each properties, you can refer to +./pinctrl-bindings.txt. + +Required sub-node properties: + - pins + - function + +Optional sub-node properties: + - bias-disable + - bias-pull-up + - bias-pull-down + - drive-strength + +*** Deprecated pin configuration and multiplexing binding + Required subnode-properties: - allwinner,pins: List of strings containing the pin name. diff --git a/Bindings/pinctrl/atmel,at91-pinctrl.txt b/Bindings/pinctrl/atmel,at91-pinctrl.txt index b7a93e80a302..9a8a45d9d8ab 100644 --- a/Bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Bindings/pinctrl/atmel,at91-pinctrl.txt @@ -98,6 +98,8 @@ DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the 01 - Low 10 - Medium 11 - High +OUTPUT (1 << 7): indicate this pin need to be configured as an output. +OUTPUT_VAL (1 << 8): output val (1 = high, 0 = low) DEBOUNCE (1 << 16): indicate this pin needs debounce. DEBOUNCE_VAL (0x3fff << 17): debounce value. diff --git a/Bindings/pinctrl/brcm,iproc-gpio.txt b/Bindings/pinctrl/brcm,iproc-gpio.txt index e4277921f3e3..a73cbeb0f309 100644 --- a/Bindings/pinctrl/brcm,iproc-gpio.txt +++ b/Bindings/pinctrl/brcm,iproc-gpio.txt @@ -3,8 +3,22 @@ Broadcom iProc GPIO/PINCONF Controller Required properties: - compatible: - Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", - "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio" + "brcm,iproc-gpio" for the generic iProc based GPIO controller IP that + supports full-featured pinctrl and GPIO functions used in various iProc + based SoCs + + May contain an SoC-specific compatibility string to accommodate any + SoC-specific features + + "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or + "brcm,cygnus-crmu-gpio" for Cygnus SoCs + + "brcm,iproc-nsp-gpio" for the iProc NSP SoC that has drive strength support + disabled + + "brcm,iproc-stingray-gpio" for the iProc Stingray SoC that has the general + pinctrl support completely disabled in this IP block. In Stingray, a + different IP block is used to handle pinctrl related functions - reg: Define the base and range of the I/O address space that contains SoC diff --git a/Bindings/pinctrl/brcm,nsp-pinmux.txt b/Bindings/pinctrl/brcm,nsp-pinmux.txt new file mode 100644 index 000000000000..603564e5fe6f --- /dev/null +++ b/Bindings/pinctrl/brcm,nsp-pinmux.txt @@ -0,0 +1,79 @@ +Broadcom NSP (Northstar plus) IOMUX Controller + +The NSP IOMUX controller supports group based mux configuration. In +addition, certain pins can be muxed to GPIO function individually. + +Required properties: +- compatible: + Must be "brcm,nsp-pinmux" + +- reg: + Should contain the register physical address and length for each of + GPIO_CONTROL0, GP_AUX_SEL and IPROC_CONFIG IOMUX registers + +Properties in subnodes: +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinmux: pinmux@1803f1c0 { + compatible = "brcm,nsp-pinmux"; + reg = <0x1803f1c0 0x04>, + <0x18030028 0x04>, + <0x1803f408 0x04>; + + pinctrl-names = "default"; + pinctrl-0 = <&pwm &gpio_b &nand_sel>; + + pwm: pwm { + function = "pwm"; + groups = "pwm0_grp", "pwm1_grp"; + }; + + gpio_b: gpio_b { + function = "gpio_b"; + groups = "gpio_b_0_grp", "gpio_b_1_grp"; + }; + + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; + }; + +List of supported functions and groups in Northstar Plus: + +"spi": "spi_grp" + +"i2c": "i2c_grp" + +"mdio": "mdio_grp" + +"pwm": "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp" + +"gpio_b": "gpio_b_0_grp", "gpio_b_1_grp", "gpio_b_2_grp", "gpio_b_3_grp" + +"uart1": "uart1_grp" + +"uart2": "uart2_grp" + +"synce": "synce_grp" + +"sata_led_grps": "sata0_led_grp", "sata1_led_grp" + +"xtal_out": "xtal_out_grp" + +"sdio": "sdio_pwr_grp", "sdio_1p8v_grp" + +"switch_led": "switch_p05_led0_grp", "switch_p05_led1_grp" + +"nand": "nand_grp" + +"emmc": "emmc_grp" diff --git a/Bindings/pinctrl/marvell,orion-pinctrl.txt b/Bindings/pinctrl/marvell,orion-pinctrl.txt index 27570a3a1741..ec8aa3c6936b 100644 --- a/Bindings/pinctrl/marvell,orion-pinctrl.txt +++ b/Bindings/pinctrl/marvell,orion-pinctrl.txt @@ -4,7 +4,9 @@ Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding part and usage. Required properties: -- compatible: "marvell,88f5181l-pinctrl", "marvell,88f5182-pinctrl", +- compatible: "marvell,88f5181-pinctrl", + "marvell,88f5181l-pinctrl", + "marvell,88f5182-pinctrl", "marvell,88f5281-pinctrl" - reg: two register areas, the first one describing the first two diff --git a/Bindings/pinctrl/meson,pinctrl.txt b/Bindings/pinctrl/meson,pinctrl.txt index 32f4a2d6d0b3..2392557ede27 100644 --- a/Bindings/pinctrl/meson,pinctrl.txt +++ b/Bindings/pinctrl/meson,pinctrl.txt @@ -5,6 +5,10 @@ Required properties for the root node: "amlogic,meson8b-cbus-pinctrl" "amlogic,meson8-aobus-pinctrl" "amlogic,meson8b-aobus-pinctrl" + "amlogic,meson-gxbb-periphs-pinctrl" + "amlogic,meson-gxbb-aobus-pinctrl" + "amlogic,meson-gxl-periphs-pinctrl" + "amlogic,meson-gxl-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt b/Bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt new file mode 100644 index 000000000000..f2abdaee9022 --- /dev/null +++ b/Bindings/pinctrl/nvidia,tegra124-dpaux-padctl.txt @@ -0,0 +1,60 @@ +Device tree binding for NVIDIA Tegra DPAUX pad controller +======================================================== + +The Tegra Display Port Auxiliary (DPAUX) pad controller manages two pins +which can be assigned to either the DPAUX channel or to an I2C +controller. + +This document defines the device-specific binding for the DPAUX pad +controller. Refer to pinctrl-bindings.txt in this directory for generic +information about pin controller device tree bindings. Please refer to +the binding document ../display/tegra/nvidia,tegra20-host1x.txt for more +details on the DPAUX binding. + +Pin muxing: +----------- + +Child nodes contain the pinmux configurations following the conventions +from the pinctrl-bindings.txt document. + +Since only three configurations are possible, only three child nodes are +needed to describe the pin mux'ing options for the DPAUX pads. +Furthermore, given that the pad functions are only applicable to a +single set of pads, the child nodes only need to describe the pad group +the functions are being applied to rather than the individual pads. + +Required properties: +- groups: Must be "dpaux-io" +- function: Must be either "aux", "i2c" or "off". + +Example: +-------- + + dpaux@545c0000 { + ... + + state_dpaux_aux: pinmux-aux { + groups = "dpaux-io"; + function = "aux"; + }; + + state_dpaux_i2c: pinmux-i2c { + groups = "dpaux-io"; + function = "i2c"; + }; + + state_dpaux_off: pinmux-off { + groups = "dpaux-io"; + function = "off"; + }; + }; + + ... + + i2c@7000d100 { + ... + pinctrl-0 = <&state_dpaux_i2c>; + pinctrl-1 = <&state_dpaux_off>; + pinctrl-names = "default", "idle"; + status = "disabled"; + }; diff --git a/Bindings/pinctrl/oxnas,pinctrl.txt b/Bindings/pinctrl/oxnas,pinctrl.txt new file mode 100644 index 000000000000..09e81a95bbfd --- /dev/null +++ b/Bindings/pinctrl/oxnas,pinctrl.txt @@ -0,0 +1,57 @@ +* Oxford Semiconductor OXNAS SoC Family Pin Controller + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +OXNAS 'pin configuration node' is a node of a group of pins which can be +used for a specific device or function. This node represents configurations of +pins, optional function, and optional mux related configuration. + +Required properties for pin controller node: + - compatible: "oxsemi,ox810se-pinctrl" or "oxsemi,ox820-pinctrl" + - oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. + - bias-pull-up: Enable weak pull-up. + +Example: + +pinctrl: pinctrl { + compatible = "oxsemi,ox810se-pinctrl"; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + pinctrl_uart2: pinctrl_uart2 { + uart2a { + pins = "gpio31"; + function = "fct3"; + }; + uart2b { + pins = "gpio32"; + function = "fct3"; + }; + }; +}; + +uart2: serial@900000 { + compatible = "ns16550a"; + reg = <0x900000 0x100000>; + clocks = <&sysclk>; + interrupts = <29>; + reg-shift = <0>; + fifo-size = <16>; + reg-io-width = <1>; + current-speed = <115200>; + no-loopback-test; + status = "disabled"; + resets = <&reset 22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; diff --git a/Bindings/pinctrl/pinctrl-aspeed.txt b/Bindings/pinctrl/pinctrl-aspeed.txt new file mode 100644 index 000000000000..2ad18c4ea55c --- /dev/null +++ b/Bindings/pinctrl/pinctrl-aspeed.txt @@ -0,0 +1,67 @@ +Aspeed Pin Controllers +---------------------- + +The Aspeed SoCs vary in functionality inside a generation but have a common mux +device register layout. + +Required properties: +- compatible : Should be any one of the following: + "aspeed,ast2400-pinctrl" + "aspeed,g4-pinctrl" + "aspeed,ast2500-pinctrl" + "aspeed,g5-pinctrl" + +The pin controller node should be a child of a syscon node with the required +property: +- compatible: "syscon", "simple-mfd" + +Refer to the the bindings described in +Documentation/devicetree/bindings/mfd/syscon.txt + +Subnode Format +-------------- + +The required properties of child nodes are (as defined in pinctrl-bindings): +- function +- groups + +Each function has only one associated pin group. Each group is named by its +function. The following values for the function and groups properties are +supported: + +aspeed,ast2400-pinctrl, aspeed,g4-pinctrl: + +ACPI BMCINT DDCCLK DDCDAT FLACK FLBUSY FLWP GPID0 GPIE0 GPIE2 GPIE4 GPIE6 I2C10 +I2C11 I2C12 I2C13 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCSMI MDIO1 +MDIO2 NCTS1 NCTS3 NCTS4 NDCD1 NDCD3 NDCD4 NDSR1 NDSR3 NDTR1 NDTR3 NRI1 NRI3 +NRI4 NRTS1 NRTS3 PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RMII1 ROM16 +ROM8 ROMCS1 ROMCS2 ROMCS3 ROMCS4 RXD1 RXD3 RXD4 SD1 SGPMI SIOPBI SIOPBO TIMER3 +TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD3 TXD4 UART6 VGAHS VGAVS VPI18 VPI24 VPI30 +VPO12 VPO24 + +aspeed,ast2500-pinctrl, aspeed,g5-pinctrl: + +GPID0 GPID2 GPIE0 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 +I2C9 MAC1LINK MDIO1 MDIO2 OSCCLK PEWAKE PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 +RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 SPI1DEBUG SPI1PASSTHRU TIMER4 TIMER5 TIMER6 +TIMER7 TIMER8 VGABIOSROM + + +Examples: + +syscon: scu@1e6e2000 { + compatible = "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; + + pinctrl: pinctrl { + compatible = "aspeed,g4-pinctrl"; + + pinctrl_i2c3_default: i2c3_default { + function = "I2C3"; + groups = "I2C3"; + }; + }; +}; + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. diff --git a/Bindings/pinctrl/pinctrl-bindings.txt b/Bindings/pinctrl/pinctrl-bindings.txt index b73c96d24f59..bf3f7b014724 100644 --- a/Bindings/pinctrl/pinctrl-bindings.txt +++ b/Bindings/pinctrl/pinctrl-bindings.txt @@ -97,6 +97,11 @@ For example: }; == Pin controller devices == +Required properties: See the pin controller driver specific documentation + +Optional properties: +#pinctrl-cells: Number of pin control cells in addition to the index within the + pin controller device instance Pin controller devices should contain the pin configuration nodes that client devices reference. @@ -119,7 +124,8 @@ For example: The contents of each of those pin configuration child nodes is defined entirely by the binding for the individual pin controller device. There -exists no common standard for this content. +exists no common standard for this content. The pinctrl framework only +provides generic helper bindings that the pin controller driver can use. The pin configuration nodes need not be direct children of the pin controller device; they may be grandchildren, for example. Whether this is legal, and @@ -156,6 +162,42 @@ state_2_node_a { pins = "mfio29", "mfio30"; }; +Optionally an altenative binding can be used if more suitable depending on the +pin controller hardware. For hardaware where there is a large number of identical +pin controller instances, naming each pin and function can easily become +unmaintainable. This is especially the case if the same controller is used for +different pins and functions depending on the SoC revision and packaging. + +For cases like this, the pin controller driver may use pinctrl-pin-array helper +binding with a hardware based index and a number of pin configuration values: + +pincontroller { + ... /* Standard DT properties for the device itself elided */ + #pinctrl-cells = <2>; + + state_0_node_a { + pinctrl-pin-array = < + 0 A_DELAY_PS(0) G_DELAY_PS(120) + 4 A_DELAY_PS(0) G_DELAY_PS(360) + ... + >; + }; + ... +}; + +Above #pinctrl-cells specifies the number of value cells in addition to the +index of the registers. This is similar to the interrupts-extended binding with +one exception. There is no need to specify the phandle for each entry as that +is already known as the defined pins are always children of the pin controller +node. Further having the phandle pointing to another pin controller would not +currently work as the pinctrl framework uses named modes to group pins for each +pin control device. + +The index for pinctrl-pin-array must relate to the hardware for the pinctrl +registers, and must not be a virtual index of pin instances. The reason for +this is to avoid mapping of the index in the dts files and the pin controller +driver as it can change. + == Generic pin configuration node content == Many data items that are represented in a pin configuration node are common diff --git a/Bindings/pinctrl/pinctrl-max77620.txt b/Bindings/pinctrl/pinctrl-max77620.txt new file mode 100644 index 000000000000..ad4fce3552bb --- /dev/null +++ b/Bindings/pinctrl/pinctrl-max77620.txt @@ -0,0 +1,127 @@ +Pincontrol driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt> +for details of the common pinctrl bindings used by client devices, +including the meaning of the phrase "pin configuration node". + +Optional Pinmux properties: +-------------------------- +Following properties are required if default setting of pins are required +at boot. +- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per + <pinctrl-binding.txt>. + +The pin configurations are defined as child of the pinctrl states node. Each +sub-node have following properties: + +Required properties: +------------------ +- pins: List of pins. Valid values of pins properties are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7. + +Optional properties: +------------------- +Following are optional properties defined as pinmux DT binding document +<pinctrl-bindings.txt>. Absence of properties will leave the configuration +on default. + function, + drive-push-pull, + drive-open-drain, + bias-pull-up, + bias-pull-down. + +Valid values for function properties are: + gpio, lpm-control-in, fps-out, 32k-out, sd0-dvs-in, sd1-dvs-in, + reference-out + +Theres is also customised properties for the GPIO1, GPIO2 and GPIO3. These +customised properties are required to configure FPS configuration parameters +of these GPIOs. Please refer <devicetree/bindings/mfd/max77620.txt> for more +detail of Flexible Power Sequence (FPS). + +- maxim,active-fps-source: FPS source for the GPIOs to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + GPIO is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + GPIO to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the GPIO get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the GPIO get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + + pinctrl-names = "default"; + pinctrl-0 = <&spmic_default>; + + spmic_default: pinmux@0 { + pin_gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + pin_gpio1 { + pins = "gpio1"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + pin_gpio2 { + pins = "gpio2"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + }; +}; diff --git a/Bindings/pinctrl/pinctrl-palmas.txt b/Bindings/pinctrl/pinctrl-palmas.txt index caf297bee1fb..c28d4eb83b76 100644 --- a/Bindings/pinctrl/pinctrl-palmas.txt +++ b/Bindings/pinctrl/pinctrl-palmas.txt @@ -35,6 +35,15 @@ Optional properties: - ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode. Selection primary or secondary function associated to GPADC_START and SYSEN2 pin/pad for DVFS2 interface +- ti,palmas-override-powerhold: This is applicable for PMICs for which + GPIO7 is configured in POWERHOLD mode which has higher priority + over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON + bit is turned off. This property enables driver to over ride the + POWERHOLD value to GPIO7 so as to turn off the PMIC in power off + scenarios. So for GPIO7 if ti,palmas-override-powerhold is set + then the GPIO_7 field should never be muxed to anything else. + It should be set to POWERHOLD by default and only in case of + power off scenarios the driver will over ride the mux value. This binding uses the following generic properties as defined in pinctrl-bindings.txt: diff --git a/Bindings/pinctrl/pinctrl-single.txt b/Bindings/pinctrl/pinctrl-single.txt index 66dcaa9efd74..e705acd3612c 100644 --- a/Bindings/pinctrl/pinctrl-single.txt +++ b/Bindings/pinctrl/pinctrl-single.txt @@ -7,6 +7,9 @@ Required properties: - reg : offset and length of the register set for the mux registers +- #pinctrl-cells : number of cells in addition to the index, set to 1 + for pinctrl-single,pins and 2 for pinctrl-single,bits + - pinctrl-single,register-width : pinmux register access width in bits - pinctrl-single,function-mask : mask of allowed pinmux function bits diff --git a/Bindings/pinctrl/pinctrl-st.txt b/Bindings/pinctrl/pinctrl-st.txt index 26bcb18f4e60..013c675b5b64 100644 --- a/Bindings/pinctrl/pinctrl-st.txt +++ b/Bindings/pinctrl/pinctrl-st.txt @@ -30,8 +30,7 @@ Second type has a dedicated interrupt per gpio bank. Pin controller node: Required properties: -- compatible : should be "st,<SOC>-<pio-block>-pinctrl" - like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on. +- compatible : should be "st,stih407-<pio-block>-pinctrl" - st,syscfg : Should be a phandle of the syscfg node. - st,retime-pin-mask : Should be mask to specify which pins can be retimed. If the property is not present, it is assumed that all the pins in the @@ -50,7 +49,11 @@ Optional properties: GPIO controller/bank node. Required properties: - gpio-controller : Indicates this device is a GPIO controller -- #gpio-cells : Should be one. The first cell is the pin number. +- #gpio-cells : Must be two. + - First cell: specifies the pin number inside the controller + - Second cell: specifies whether the pin is logically inverted. + - 0 = active high + - 1 = active low - st,bank-name : Should be a name string for this bank as specified in datasheet. @@ -76,23 +79,23 @@ include/dt-bindings/interrupt-controller/irq.h Example: pin-controller-sbc { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stih415-sbc-pinctrl"; - st,syscfg = <&syscfg_sbc>; - reg = <0xfe61f080 0x4>; - reg-names = "irqmux"; - interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "irqmux"; - ranges = <0 0xfe610000 0x5000>; - - PIO0: gpio@fe610000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stih407-sbc-pinctrl"; + st,syscfg = <&syscfg_sbc>; + reg = <0x0961f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>; + interrupt-names = "irqmux"; + ranges = <0 0x09610000 0x6000>; + + pio0: gpio@09610000 { gpio-controller; - #gpio-cells = <1>; + #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - reg = <0 0x100>; - st,bank-name = "PIO0"; + reg = <0x0 0x100>; + st,bank-name = "PIO0"; }; ... pin-functions nodes follow... @@ -162,7 +165,7 @@ pin-controller { sdhci0:sdhci@fe810000{ ... - interrupt-parent = <&PIO3>; + interrupt-parent = <&pio3>; #interrupt-cells = <2>; interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; /* Interrupt line via PIO3-3 */ interrupt-names = "card-detect"; diff --git a/Bindings/pinctrl/pinctrl-sx150x.txt b/Bindings/pinctrl/pinctrl-sx150x.txt new file mode 100644 index 000000000000..bf76867168e9 --- /dev/null +++ b/Bindings/pinctrl/pinctrl-sx150x.txt @@ -0,0 +1,74 @@ +SEMTECH SX150x GPIO expander bindings + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +Required properties: +- compatible: should be one of : + "semtech,sx1501q", + "semtech,sx1502q", + "semtech,sx1503q", + "semtech,sx1504q", + "semtech,sx1505q", + "semtech,sx1506q", + "semtech,sx1507q", + "semtech,sx1508q", + "semtech,sx1509q". + +- reg: The I2C slave address for this device. + +- #gpio-cells: Should be 2. The first cell is the GPIO number and the + second cell is used to specify optional parameters: + bit 0: polarity (0: normal, 1: inverted) + +- gpio-controller: Marks the device as a GPIO controller. + +Optional properties : +- interrupt-parent: phandle of the parent interrupt controller. + +- interrupts: Interrupt specifier for the controllers interrupt. + +- interrupt-controller: Marks the device as a interrupt controller. + +- semtech,probe-reset: Will trigger a reset of the GPIO expander on probe, + only for sx1507q, sx1508q and sx1509q + +The GPIO expander can optionally be used as an interrupt controller, in +which case it uses the default two cell specifier. + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - bias-disable: disable any pin bias, except the OSCIO pin + - bias-pull-up: pull up the pin, except the OSCIO pin + - bias-pull-down: pull down the pin, except the OSCIO pin + - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin + - drive-push-pull: drive actively high and low + - drive-open-drain: drive with open drain only for sx1507q, sx1508q and sx1509q and except the OSCIO pin + - output-low: set the pin to output mode with low level + - output-high: set the pin to output mode with high level + +Example: + + i2c0gpio-expander@20{ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1506q"; + reg = <0x20>; + interrupt-parent = <&gpio_1>; + interrupts = <16 0>; + + gpio-controller; + interrupt-controller; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio1_cfg_pins>; + + gpio1_cfg_pins: gpio1-cfg { + pins = "gpio1"; + bias-pull-up; + }; + }; diff --git a/Bindings/pinctrl/qcom,mdm9615-pinctrl.txt b/Bindings/pinctrl/qcom,mdm9615-pinctrl.txt new file mode 100644 index 000000000000..1b52f01ddcb7 --- /dev/null +++ b/Bindings/pinctrl/qcom,mdm9615-pinctrl.txt @@ -0,0 +1,152 @@ +Qualcomm MDM9615 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MDM9615 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,mdm9615-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio87 + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. + Valid values are: + gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart, + sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio, + cdc_mclk + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + msmgpio: pinctrl@800000 { + compatible = "qcom,mdm9615-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 16 0x4>; + + gsbi8_uart: gsbi8-uart { + mux { + pins = "gpio34", "gpio35"; + function = "gsbi8"; + }; + + tx { + pins = "gpio34"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio35"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/Bindings/pinctrl/qcom,msm8660-pinctrl.txt b/Bindings/pinctrl/qcom,msm8660-pinctrl.txt index 77aa11790163..df9a838ec5f9 100644 --- a/Bindings/pinctrl/qcom,msm8660-pinctrl.txt +++ b/Bindings/pinctrl/qcom,msm8660-pinctrl.txt @@ -52,7 +52,7 @@ Valid values for function are: gsbi2_spi_cs3_n, gsbi3, gsbi3_spi_cs1_n, gsbi3_spi_cs2_n, gsbi3_spi_cs3_n, gsbi4, gsbi5, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10, gsbi11, gsbi12, hdmi, i2s, lcdc, mdp_vsync, mi2s, pcm, ps_hold, sdc1, sdc2, sdc5, tsif1, tsif2, usb_fs1, - usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, + usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, ebi2, ebi2cs Example: diff --git a/Bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Bindings/pinctrl/qcom,msm8974-pinctrl.txt index e4d6a9d20f7d..453bd7c76d6b 100644 --- a/Bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -49,6 +49,9 @@ Valid values for pins are: sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data Supports bias and drive-strength + hsic_data, hsic_strobe + Supports only mux + Valid values for function are: cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm, blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1, @@ -70,7 +73,7 @@ Valid values for function are: cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc, hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk, gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s, - ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, gpio + ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl, gpio (Note that this is not yet the complete list of functions) diff --git a/Bindings/pinctrl/qcom,msm8994-pinctrl.txt b/Bindings/pinctrl/qcom,msm8994-pinctrl.txt new file mode 100644 index 000000000000..13cd629f896e --- /dev/null +++ b/Bindings/pinctrl/qcom,msm8994-pinctrl.txt @@ -0,0 +1,177 @@ +Qualcomm MSM8994 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8994 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain one of: + "qcom,msm8992-pinctrl", + "qcom,msm8994-pinctrl". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio145 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data sdc1_rclk, sdc2_clk, + sdc2_cmd, sdc2_data + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + audio_ref_clk, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, + blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_i2c9, blsp_i2c10, blsp_i2c11, + blsp_i2c12, blsp_spi1, blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, + blsp_spi2, blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3, + blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, + blsp_spi10, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3, blsp_spi11, + blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3, blsp_uart4, blsp_uart5, + blsp_uart6, blsp_uart7, blsp_uart8, blsp_uart9, blsp_uart10, blsp_uart11, + blsp_uart12, blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5, + blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10, blsp_uim11, + blsp_uim12, blsp11_i2c_scl_b, blsp11_i2c_sda_b, blsp11_uart_rx_b, + blsp11_uart_tx_b, cam_mclk0, cam_mclk1, cam_mclk2, cam_mclk3, + cci_async_in0, cci_async_in1, cci_async_in2, cci_i2c0, cci_i2c1, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, + gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a, + gcc_gp3_clk_b, gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, + gp1_clk, gps_tx, gsm_tx, hdmi_cec, hdmi_ddc, hdmi_hpd, hdmi_rcv, + mdp_vsync, mss_lte, nav_pps, nav_tsync, qdss_cti_trig_in_a, + qdss_cti_trig_in_b, qdss_cti_trig_in_c, qdss_cti_trig_in_d, + qdss_cti_trig_out_a, qdss_cti_trig_out_b, qdss_cti_trig_out_c, + qdss_cti_trig_out_d, qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, + qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b, qua_mi2s, pci_e0, + pci_e1, pri_mi2s, sdc4, sec_mi2s, slimbus, spkr_i2s, ter_mi2s, tsif1, + tsif2, uim_batt_alarm, uim1, uim2, uim3, uim4, gpio + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + msmgpio: pinctrl@fd510000 { + compatible = "qcom,msm8994-pinctrl"; + reg = <0xfd510000 0x4000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + blsp1_uart2_default: blsp1_uart2_default { + pinmux { + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; + }; + pinconf { + pins = "gpio4", "gpio5"; + drive-strength = <16>; + bias-disable; + }; + }; + }; diff --git a/Bindings/pinctrl/qcom,pmic-gpio.txt b/Bindings/pinctrl/qcom,pmic-gpio.txt index a54c39ebbf8b..8d893a874634 100644 --- a/Bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Bindings/pinctrl/qcom,pmic-gpio.txt @@ -17,6 +17,9 @@ PMIC's from Qualcomm. "qcom,pm8994-gpio" "qcom,pma8084-gpio" + And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" + if the device is on an spmi bus or an ssbi bus respectively + - reg: Usage: required Value type: <prop-encoded-array> @@ -183,7 +186,7 @@ to specify in a pin configuration subnode: Example: pm8921_gpio: gpio@150 { - compatible = "qcom,pm8921-gpio"; + compatible = "qcom,pm8921-gpio", "qcom,ssbi-gpio"; reg = <0x150 0x160>; interrupts = <192 1>, <193 1>, <194 1>, <195 1>, <196 1>, <197 1>, diff --git a/Bindings/pinctrl/qcom,pmic-mpp.txt b/Bindings/pinctrl/qcom,pmic-mpp.txt index d74e631e10da..2ab95bc26066 100644 --- a/Bindings/pinctrl/qcom,pmic-mpp.txt +++ b/Bindings/pinctrl/qcom,pmic-mpp.txt @@ -9,6 +9,7 @@ of PMIC's from Qualcomm. Definition: Should contain one of: "qcom,pm8018-mpp", "qcom,pm8038-mpp", + "qcom,pm8058-mpp", "qcom,pm8821-mpp", "qcom,pm8841-mpp", "qcom,pm8916-mpp", @@ -18,6 +19,9 @@ of PMIC's from Qualcomm. "qcom,pm8994-mpp", "qcom,pma8084-mpp", + And must contain either "qcom,spmi-mpp" or "qcom,ssbi-mpp" + if the device is on an spmi bus or an ssbi bus respectively. + - reg: Usage: required Value type: <prop-encoded-array> @@ -157,7 +161,7 @@ to specify in a pin configuration subnode: Example: mpps@a000 { - compatible = "qcom,pm8841-mpp"; + compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp"; reg = <0xa000>; gpio-controller; #gpio-cells = <2>; diff --git a/Bindings/pinctrl/renesas,pfc-pinctrl.txt b/Bindings/pinctrl/renesas,pfc-pinctrl.txt index 74e6ec0339d6..13df9498311a 100644 --- a/Bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -17,9 +17,11 @@ Required Properties: - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2-W) compatible pin-controller. + - "renesas,pfc-r8a7792": for R8A7792 (R-Car V2H) compatible pin-controller. - "renesas,pfc-r8a7793": for R8A7793 (R-Car M2-N) compatible pin-controller. - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. + - "renesas,pfc-r8a7796": for R8A7796 (R-Car M3-W) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. - reg: Base address and length of each memory resource used by the pin @@ -72,7 +74,7 @@ Pin Configuration Node Properties: The pin configuration parameters use the generic pinconf bindings defined in pinctrl-bindings.txt in this directory. The supported parameters are -bias-disable, bias-pull-up, bias-pull-down, drive strength and power-source. For +bias-disable, bias-pull-up, bias-pull-down, drive-strength and power-source. For pins that have a configurable I/O voltage, the power-source value should be the nominal I/O voltage in millivolts. diff --git a/Bindings/pinctrl/rockchip,pinctrl.txt b/Bindings/pinctrl/rockchip,pinctrl.txt index c68b9554561f..4722bc61a1a2 100644 --- a/Bindings/pinctrl/rockchip,pinctrl.txt +++ b/Bindings/pinctrl/rockchip,pinctrl.txt @@ -19,10 +19,11 @@ The pins are grouped into up to 5 individual pin banks which need to be defined as gpio sub-nodes of the pinmux controller. Required properties for iomux controller: - - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" - "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" - "rockchip,rk3228-pinctrl", "rockchip,rk3288-pinctrl" - "rockchip,rk3368-pinctrl", "rockchip,rk3399-pinctrl" + - compatible: one of "rockchip,rk1108-pinctrl", "rockchip,rk2928-pinctrl" + "rockchip,rk3066a-pinctrl", "rockchip,rk3066b-pinctrl" + "rockchip,rk3188-pinctrl", "rockchip,rk3228-pinctrl" + "rockchip,rk3288-pinctrl", "rockchip,rk3368-pinctrl" + "rockchip,rk3399-pinctrl" - rockchip,grf: phandle referencing a syscon providing the "general register files" diff --git a/Bindings/pinctrl/samsung-pinctrl.txt b/Bindings/pinctrl/samsung-pinctrl.txt index 6db16b90873a..1baf19eecabf 100644 --- a/Bindings/pinctrl/samsung-pinctrl.txt +++ b/Bindings/pinctrl/samsung-pinctrl.txt @@ -19,11 +19,30 @@ Required Properties: - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller. - "samsung,exynos5410-pinctrl": for Exynos5410 compatible pin-controller. - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller. + - "samsung,exynos5433-pinctrl": for Exynos5433 compatible pin-controller. - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of the address space it occupies. + - reg: Second base address of the pin controller if the specific registers + of the pin controller are separated into the different base address. + + Eg: GPF[1-5] of Exynos5433 are separated into the two base address. + - First base address is for GPAx and GPF[1-5] external interrupt + registers. + - Second base address is for GPF[1-5] pinctrl registers. + + pinctrl_0: pinctrl@10580000 { + compatible = "samsung,exynos5433-pinctrl"; + reg = <0x10580000 0x1a20>, <0x11090000 0x100>; + + wakeup-interrupt-controller { + compatible = "samsung,exynos7-wakeup-eint"; + interrupts = <0 16 0>; + }; + }; + - Pin banks as child nodes: Pin banks of the controller are represented by child nodes of the controller node. Bank name is taken from name of the node. Each bank node must contain following properties: @@ -229,6 +248,8 @@ Example: A pin-controller node with pin banks: Example 1: A pin-controller node with pin groups. + #include <dt-bindings/pinctrl/samsung.h> + pinctrl_0: pinctrl@11400000 { compatible = "samsung,exynos4210-pinctrl"; reg = <0x11400000 0x1000>; @@ -238,53 +259,53 @@ Example 1: A pin-controller node with pin groups. uart0_data: uart0-data { samsung,pins = "gpa0-0", "gpa0-1"; - samsung,pin-function = <2>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; uart0_fctl: uart0-fctl { samsung,pins = "gpa0-2", "gpa0-3"; - samsung,pin-function = <2>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; uart1_data: uart1-data { samsung,pins = "gpa0-4", "gpa0-5"; - samsung,pin-function = <2>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; uart1_fctl: uart1-fctl { samsung,pins = "gpa0-6", "gpa0-7"; - samsung,pin-function = <2>; - samsung,pin-pud = <0>; - samsung,pin-drv = <0>; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; i2c2_bus: i2c2-bus { samsung,pins = "gpa0-6", "gpa0-7"; - samsung,pin-function = <3>; - samsung,pin-pud = <3>; - samsung,pin-drv = <0>; + samsung,pin-function = <EXYNOS_PIN_FUNC_3>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; sd4_bus8: sd4-bus-width8 { part-1 { samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6"; - samsung,pin-function = <3>; - samsung,pin-pud = <3>; - samsung,pin-drv = <3>; + samsung,pin-function = <EXYNOS_PIN_FUNC_3>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; }; part-2 { samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6"; - samsung,pin-function = <4>; - samsung,pin-pud = <4>; - samsung,pin-drv = <3>; + samsung,pin-function = <EXYNOS_PIN_FUNC_4>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; }; }; }; diff --git a/Bindings/pinctrl/st,stm32-pinctrl.txt b/Bindings/pinctrl/st,stm32-pinctrl.txt index 7b4800cc251e..b24583aa34c3 100644 --- a/Bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Bindings/pinctrl/st,stm32-pinctrl.txt @@ -9,6 +9,7 @@ Pin controller node: Required properies: - compatible: value should be one of the following: (a) "st,stm32f429-pinctrl" + (b) "st,stm32f746-pinctrl" - #address-cells: The value of this property must be 1 - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to @@ -31,6 +32,11 @@ Required properties: Optional properties: - reset: : Reference to the reset controller + - interrupt-parent: phandle of the interrupt parent to which the external + GPIO interrupts are forwarded to. + - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node + which includes IRQ mux selection register, and the offset of the IRQ mux + selection register. Example: #include <dt-bindings/pinctrl/stm32f429-pinfunc.h> diff --git a/Bindings/pinctrl/ti,da850-pupd.txt b/Bindings/pinctrl/ti,da850-pupd.txt new file mode 100644 index 000000000000..7f2980567c9f --- /dev/null +++ b/Bindings/pinctrl/ti,da850-pupd.txt @@ -0,0 +1,55 @@ +* Pin configuration for TI DA850/OMAP-L138/AM18x + +These SoCs have a separate controller for setting bias (internal pullup/down). +Bias can only be selected for groups rather than individual pins. + +Required Properties: + + - compatible: Must be "ti,da850-pupd" + - reg: Base address and length of the memory resource used by the pullup/down + controller hardware module. + +The controller node also acts as a container for pin group configuration nodes. +The names of these groups are ignored. + +Pin Group Node Properties: + +- groups: An array of strings, each string containing the name of a pin group. + Valid names are "cp0".."cp31". + +The pin configuration parameters use the generic pinconf bindings defined in +pinctrl-bindings.txt in this directory. The supported parameters are +bias-disable, bias-pull-up, bias-pull-down. + + +Example +------- + +In common dtsi file: + + pinconf: pin-controller@22c00c { + compatible = "ti,da850-pupd"; + reg = <0x22c00c 0x8>; + }; + +In board-specific file: + + &pinconf { + pinctrl-0 = <&pinconf_bias_groups>; + pinctrl-names = "default"; + + pinconf_bias_groups: bias-groups { + pull-up { + groups = "cp30", "cp31"; + bias-pull-up; + }; + pull-down { + groups = "cp29", "cp28"; + bias-pull-down; + }; + disable { + groups = "cp27", "cp26"; + bias-disable; + }; + }; + }; |