diff options
Diffstat (limited to 'src/arm/am57xx-idk-common.dtsi')
| -rw-r--r-- | src/arm/am57xx-idk-common.dtsi | 133 |
1 files changed, 132 insertions, 1 deletions
diff --git a/src/arm/am57xx-idk-common.dtsi b/src/arm/am57xx-idk-common.dtsi index 0e63b9dff6e7..814a720d5c3d 100644 --- a/src/arm/am57xx-idk-common.dtsi +++ b/src/arm/am57xx-idk-common.dtsi @@ -43,6 +43,58 @@ regulator-always-on; regulator-boot-on; }; + + leds-iio { + status = "disabled"; + compatible = "gpio-leds"; + led-out0 { + label = "out0"; + gpios = <&tpic2810 0 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out1 { + label = "out1"; + gpios = <&tpic2810 1 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out2 { + label = "out2"; + gpios = <&tpic2810 2 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out3 { + label = "out3"; + gpios = <&tpic2810 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out4 { + label = "out4"; + gpios = <&tpic2810 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out5 { + label = "out5"; + gpios = <&tpic2810 5 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out6 { + label = "out6"; + gpios = <&tpic2810 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-out7 { + label = "out7"; + gpios = <&tpic2810 7 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; }; &i2c1 { @@ -57,6 +109,7 @@ #interrupt-cells = <2>; interrupt-controller; ti,system-power-controller; + ti,palmas-override-powerhold; tps659038_pmic { compatible = "ti,tps659038-pmic"; @@ -250,6 +303,35 @@ gpio-controller; #gpio-cells = <2>; }; + + extcon_usb2: tps659038_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + /* ID & VBUS GPIOs provided in board dts */ + }; + }; +}; + +&mcspi3 { + status = "okay"; + ti,pindir-d0-out-d1-in; + + sn65hvs882: sn65hvs882@0 { + compatible = "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + }; + + tpic2810: tpic2810@60 { + compatible = "ti,tpic2810"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; }; }; @@ -294,7 +376,7 @@ }; &usb2 { - dr_mode = "otg"; + dr_mode = "peripheral"; }; &mmc2 { @@ -304,3 +386,52 @@ ti,non-removable; max-frequency = <96000000>; }; + +&qspi { + status = "okay"; + + spi-max-frequency = <76800000>; + m25p80@0 { + compatible = "s25fl256s1", "jedec,spi-nor"; + spi-max-frequency = <76800000>; + reg = <0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + #address-cells = <1>; + #size-cells = <1>; + + /* MTD partition table. + * The ROM checks the first four physical blocks + * for a valid file to boot and the flash here is + * 64KiB block size. + */ + partition@0 { + label = "QSPI.SPL"; + reg = <0x00000000 0x000040000>; + }; + partition@1 { + label = "QSPI.u-boot"; + reg = <0x00040000 0x00100000>; + }; + partition@2 { + label = "QSPI.u-boot-spl-os"; + reg = <0x00140000 0x00080000>; + }; + partition@3 { + label = "QSPI.u-boot-env"; + reg = <0x001c0000 0x00010000>; + }; + partition@4 { + label = "QSPI.u-boot-env.backup1"; + reg = <0x001d0000 0x0010000>; + }; + partition@5 { + label = "QSPI.kernel"; + reg = <0x001e0000 0x0800000>; + }; + partition@6 { + label = "QSPI.file-system"; + reg = <0x009e0000 0x01620000>; + }; + }; +}; |