diff options
Diffstat (limited to 'src/arm/sun9i-a80-cubieboard4.dts')
| -rw-r--r-- | src/arm/sun9i-a80-cubieboard4.dts | 337 |
1 files changed, 320 insertions, 17 deletions
diff --git a/src/arm/sun9i-a80-cubieboard4.dts b/src/arm/sun9i-a80-cubieboard4.dts index eb2ccd0a3bd5..67b02fe7f11c 100644 --- a/src/arm/sun9i-a80-cubieboard4.dts +++ b/src/arm/sun9i-a80-cubieboard4.dts @@ -45,7 +45,6 @@ /dts-v1/; #include "sun9i-a80.dtsi" -#include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/pinctrl/sun4i-a10.h> @@ -77,38 +76,45 @@ gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ }; }; -}; -&pio { - led_pins_cubieboard4: led-pins@0 { - allwinner,pins = "PH6", "PH17"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; - }; - - mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 { - allwinner,pins = "PH18"; - allwinner,function = "gpio_in"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ }; }; &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */ cd-inverted; status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>, <&wifi_en_pin_cubieboard4>; + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_cldo3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&mmc1_pins { + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -120,14 +126,311 @@ allwinner,drive = <SUN4I_PINCTRL_40_MA>; }; +&osc32k { + /* osc32k input is from AC100 */ + clocks = <&ac100_rtc 0>; +}; + +&pio { + led_pins_cubieboard4: led-pins@0 { + allwinner,pins = "PH6", "PH17"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 { + allwinner,pins = "PH18"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + &r_ir { status = "okay"; }; +&r_pio { + wifi_en_pin_cubieboard4: wifi_en_pin@0 { + allwinner,pins = "PL2"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + &r_rsb { status = "okay"; + + axp809: pmic@3a3 { + reg = <0x3a3>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + regulators { + reg_aldo1: aldo1 { + /* + * TODO: This should be handled by the + * USB PHY driver. + */ + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc33-usbh"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pb-io-cam"; + }; + + aldo3 { + /* unused */ + }; + + reg_dc5ldo: dc5ldo { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus-09-usbh"; + }; + + reg_dcdc1: dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v"; + }; + + reg_dcdc2: dcdc2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; + }; + + reg_dcdc3: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; + }; + + reg_dcdc4: dcdc4 { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys-usb0-hdmi"; + }; + + reg_dcdc5: dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1425000>; + regulator-max-microvolt = <1575000>; + regulator-name = "vcc-dram"; + }; + + reg_dldo1: dldo1 { + /* + * The WiFi chip supports a wide range + * (3.0 ~ 4.8V) of voltages, and so does + * this regulator (3.0 ~ 4.2V), but + * Allwinner SDK always sets it to 3.3V. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; + }; + + reg_dldo2: dldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pl"; + }; + + reg_eldo1: eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dvdd-cam"; + }; + + reg_eldo2: eldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pe"; + }; + + reg_eldo3: eldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pm-codec-io1"; + }; + + reg_ldo_io0: ldo_io0 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pg"; + }; + + reg_ldo_io1: ldo_io1 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pa-gmac-2v5"; + }; + + reg_rtc_ldo: rtc_ldo { + regulator-name = "vcc-rtc-vdd1v8-io"; + }; + + sw { + /* unused */ + }; + }; + }; + + axp806: pmic@745 { + compatible = "x-powers,axp806"; + reg = <0x745>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + bldoin-supply = <®_dcdce>; + + regulators { + reg_s_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; + }; + + aldo2 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo2"; + }; + + aldo3 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo3"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-name = "vcc18-efuse-adc-display-csi"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-name = + "vdd18-drampll-vcc18-pll-cpvdd"; + }; + + bldo3 { + /* unused */ + }; + + reg_bldo4: bldo4 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vcc12-hsic"; + }; + + reg_cldo1: cldo1 { + /* + * This was 3V in the original design, but + * 3.3V is the recommended supply voltage + * for the Ethernet PHY. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-gmac-phy"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "afvcc-cam"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-io-wifi-codec-io2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-vpu"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2100000>; + regulator-name = "vcc-bldo-codec-ldoin"; + }; + + sw { + /* + * unused, but use a different name to + * avoid name clash with axp809's sw + */ + regulator-name = "s_sw"; + }; + }; + }; + + ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", + "cko2_rtc", + "cko3_rtc"; + }; + }; }; +#include "axp809.dtsi" + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; |