.\" Copyright (c) 2013, Sean Bruno .\" All rights reserved. .\" .\" Redistribution and use in source and binary forms, with or without .\" modification, are permitted provided that the following conditions .\" are met: .\" 1. Redistributions of source code must retain the above copyright .\" notice, this list of conditions and the following disclaimer. .\" 2. Redistributions in binary form must reproduce the above copyright .\" notice, this list of conditions and the following disclaimer in the .\" documentation and/or other materials provided with the distribution. .\" .\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE .\" ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE .\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL .\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS .\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) .\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT .\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY .\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF .\" SUCH DAMAGE. .\" .\" $FreeBSD$ .\" .Dd June 27, 2019 .Dt GPIO 4 .Os .Sh NAME .Nm gpiobus .Nd GPIO bus system .Sh SYNOPSIS To compile these devices into your kernel and use the device hints, place the following lines in your kernel configuration file: .Bd -ragged -offset indent .Cd "device gpio" .Cd "device gpioc" .Cd "device gpioiic" .Cd "device gpioled" .Ed .Pp Additional device entries for the .Li ARM architecture include: .Bd -ragged -offset indent .Cd "device a10_gpio" .Cd "device bcm_gpio" .Cd "device imx51_gpio" .Cd "device lpcgpio" .Cd "device mv_gpio" .Cd "device ti_gpio" .Cd "device gpio_avila" .Cd "device gpio_cambria" .Cd "device zy7_gpio" .Cd "device pxagpio" .Ed .Pp Additional device entries for the .Li MIPS architecture include: .Bd -ragged -offset indent .Cd "device ar71xxx_gpio" .Cd "device octeon_gpio" .Cd "device rt305_gpio" .Ed .Pp Additional device entries for the .Li POWERPC architecture include: .Bd -ragged -offset indent .Cd "device wiigpio" .Cd "device macgpio" .Ed .Sh DESCRIPTION The .Nm system provides a simple interface to the GPIO pins that are usually available on embedded architectures and can provide bit banging style devices to the system. .Pp The acronym .Li GPIO means .Dq General-Purpose Input/Output. .Pp The BUS physically consists of multiple pins that can be configured for input/output, IRQ delivery, SDA/SCL .Em iicbus use, etc. .Pp On some embedded architectures (like MIPS), discovery of the bus and configuration of the pins is done via .Xr device.hints 5 in the platform's kernel .Xr config 5 file. .Pp On some others (like ARM), where .Xr FDT 4 is used to describe the device tree, the bus discovery is done via the DTS passed to the kernel, being either statically compiled in, or by a variety of ways where the boot loader (or Open Firmware enabled system) passes the DTS blob to the kernel at boot. .Pp On a .Xr device.hints 5 based system these hints can be used to configure drivers for devices attached to .Nm pins: .Bl -tag -width ".Va hint.driver.unit.pin_list" .It Va hint.driver.unit.at The .Nm gpiobus where the device is attached. For example, .Qq gpiobus0 . .Ar driver and .Ar unit are the driver name and the unit number for the device driver. .It Va hint.driver.unit.pins This is a bitmask of the pins on the .Nm gpiobus that are connected to the device. The pins will be allocated to the specified driver instance. Only pins with numbers from 0 to 31 can be specified using this hint. .It Va hint.driver.unit.pin_list This is a list of pin numbers of pins on the .Nm gpiobus that are connected to the device. The pins will be allocated to the specified driver instance. This is a more user friendly alternative to the .Ar pins hint. Additionally, this hint allows specifying pin numbers greater than 31. The numbers can be decimal or hexadecimal with 0x prefix. Any non-digit character can be used as a separator. For example, it can be a comma, a slash or a space. The separator can be followed by any number of space characters. .El .Pp The following .Xr device.hints 5 are only provided by the .Cd ar71xx_gpio driver: .Bl -tag -width ".Va hint.gpio.function_clear" .It Va hint.gpio.%d.pinmask This is a bitmask of pins on the GPIO board that we would like to expose for use to the host operating system. To expose pin 0, 4 and 7, use the bitmask of 10010001 converted to the hexadecimal value 0x0091. .It Va hint.gpio.%d.pinon This is a bitmask of pins on the GPIO board that will be set to ON at host start. To set pin 2, 5 and 13 to be set ON at boot, use the bitmask of 10000000010010 converted to the hexadecimal value 0x2012. .It Va hint.gpio.function_set .It Va hint.gpio.function_clear These are bitmasks of pins that will remap a pin to handle a specific function (USB, UART TX/RX, etc) in the Atheros function registers. This is mainly used to set/clear functions that we need when they are set up or not set up by uBoot. .El .Pp Simply put, each pin of the GPIO interface is connected to an input/output of some device in a system. .Sh SEE ALSO .Xr gpioiic 4 , .Xr gpioled 4 , .Xr iicbus 4 , .Xr device.hints 5 , .Xr gpioctl 8 .Sh HISTORY The .Nm manual page first appeared in .Fx 10.0 . .Sh AUTHORS This manual page was written by .An Sean Bruno Aq Mt sbruno@FreeBSD.org .