# $FreeBSD$

# arge1 MDIO bus
hint.argemdio.0.at="nexus0"
hint.argemdio.0.maddr=0x1a000000
hint.argemdio.0.msize=0x1000
hint.argemdio.0.order=0

# Override MAC Address with the one on EEPROM
hint.arge.0.eeprommac=0x1fff0000

# arge0: dedicated switch port; RMII; dedicated PHY 4 on switch, connected
# via internal switch MDIO bus.
hint.arge.0.media=100           # Map to 100/full
hint.arge.0.fduplex=1           #
hint.arge.0.phymask=0x10        # PHY4
hint.arge.0.mdio=mdioproxy1     # .. off of the switch mdiobus

# arge1: nail to 1000/full, RMII - connected to the switch
hint.arge.1.media=1000          # Map to 1000/full
hint.arge.1.fduplex=1           #
hint.arge.1.phymask=0x0         # no directly mapped PHYs

#
# AR7240 switch config
#
hint.arswitch.0.at="mdio0"
hint.arswitch.0.is_7240=1       # We need to be explicitly told this
hint.arswitch.0.numphys=4       # 4 active switch PHYs (PHY 0 -> 3)
hint.arswitch.0.phy4cpu=1       # Yes, PHY 4 == dedicated PHY
hint.arswitch.0.is_rgmii=0      # No, not RGMII
hint.arswitch.0.is_gmii=0       # No, not GMII

# ath0 hint - pcie slot 0
hint.pcib.0.bus.0.0.0.ath_fixup_addr=0x1fff1000
hint.pcib.0.bus.0.0.0.ath_fixup_size=4096

# ath
hint.ath.0.eeprom_firmware="pcib.0.bus.0.0.0.eeprom_firmware"

# GPIO pins
# Pin 0: red led (sig1)
# Pin 1: yellow led (sig2)
# Pin 11: green len (sig3)
# Pin 7: green len (sig4)
# Pin 12: Reset switch
hint.gpio.0.pinmask=0x1883

# Signal leds
hint.gpioled.0.at="gpiobus0"
hint.gpioled.0.name="sig1"
hint.gpioled.0.pins=0x0001     # pin 0
hint.gpioled.1.at="gpiobus0"
hint.gpioled.1.name="sig2"
hint.gpioled.1.pins=0x0002     # pin 1
hint.gpioled.2.at="gpiobus0"
hint.gpioled.2.name="sig3"
hint.gpioled.2.pins=0x0800     # pin 11
hint.gpioled.3.at="gpiobus0"
hint.gpioled.3.name="sig4"
hint.gpioled.3.pins=0x0080     # pin 7

# GEOM_MAP
#
# Rocket M2 HP
#
# mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1024k(kernel),6528k(rootfs),256k(cfg),64k(EEPROM)

hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x00040000       # 256k u-boot
hint.map.0.name="u-boot"
hint.map.0.readonly=1

hint.map.1.at="flash/spi0"
hint.map.1.start=0x00040000
hint.map.1.end=0x00050000       # 64k u-boot-env 
hint.map.1.name="u-boot-env"
hint.map.1.readonly=1

hint.map.2.at="flash/spi0"
hint.map.2.start=0x00050000
hint.map.2.end="search:0x00100000:0x10000:.!/bin/sh"
hint.map.2.name="kernel"
hint.map.2.readonly=1

hint.map.3.at="flash/spi0"
hint.map.3.start="search:0x00100000:0x10000:.!/bin/sh"
hint.map.3.end=0x007b0000
hint.map.3.name="rootfs"
hint.map.3.readonly=0

hint.map.4.at="flash/spi0"
hint.map.4.start=0x007b0000
hint.map.4.end=0x007f0000       # 256k cfg
hint.map.4.name="cfg"
hint.map.4.readonly=0

hint.map.5.at="flash/spi0"
hint.map.5.start=0x007f0000
hint.map.5.end=0x00800000       # 64k EEPROM
hint.map.5.name="eeprom"
hint.map.5.readonly=1