Add more s/FreeBSD/&os; replacements to the article where possible.

Approved by:    jkois (mentor)

1 files changed, 10 insertions, 10 deletions

diff --git a/en_US.ISO8859-1/articles/solid-state/article.sgml b/en_US.ISO8859-1/articles/solid-state/article.sgml
index a50abe521e..d9b93068f0 100644
--- a/en_US.ISO8859-1/articles/solid-state/article.sgml
+++ b/en_US.ISO8859-1/articles/solid-state/article.sgml
@@ -38,7 +38,7 @@
 
 <article>
   <articleinfo>
-    <title>FreeBSD and Solid State Devices</title>
+    <title>&os; and Solid State Devices</title>
 
     <authorgroup>
       <author>
@@ -67,7 +67,7 @@
     &legalnotice;
     
     <abstract>
-      <para>This article covers the use of solid state disk devices in FreeBSD
+      <para>This article covers the use of solid state disk devices in &os;
 	to create embedded systems.</para>
     
       <para>Embedded systems have the advantage of increased stability due to
@@ -114,7 +114,7 @@
       to the IDE bus and are compatible with the ATA command set.  Therefore,
       with a very simple and low-cost adaptor, these devices can be attached
       directly to an IDE bus in a computer.  Once implemented in this manner,
-      operating systems such as FreeBSD see the device as a normal hard disk
+      operating systems such as &os; see the device as a normal hard disk
       (albeit small).</para>
 
     <para>Other solid state disk solutions do exist, but their expense,
@@ -136,7 +136,7 @@
       <filename>/tmp</filename> and <filename>/var</filename> are mounted as
       memory filesystems to allow the system to create logs and update
       counters and temporary files.  Memory filesystems are a critical
-      component to a successful solid state FreeBSD implementation.</para>
+      component to a successful solid state &os; implementation.</para>
 
     <para>You should make sure the following lines exist in your kernel
       configuration file:</para>
@@ -210,12 +210,12 @@ pseudo-device   md              # memory disk</programlisting>
   <sect1>
     <title>Building a File System From Scratch</title>
 
-    <para>Because ATA compatible compact-flash cards are seen by FreeBSD as
+    <para>Because ATA compatible compact-flash cards are seen by &os; as
       normal IDE hard drives, you could
-      theoretically install FreeBSD from the network using the kern and
+      theoretically install &os; from the network using the kern and
       mfsroot floppies or from a CD.</para>
 
-    <para>However, even a small installation of FreeBSD using normal
+    <para>However, even a small installation of &os; using normal
       installation procedures can produce a system in size of greater than 200
       megabytes.  Because most people will be using smaller flash memory
       devices (128 megabytes is considered fairly large - 32 or even 16
@@ -224,7 +224,7 @@ pseudo-device   md              # memory disk</programlisting>
       smallest of conventional installations.</para>
 
     <para>The easiest way to overcome this space limitation is to install
-      FreeBSD using conventional means to a normal hard disk.  After the
+      &os; using conventional means to a normal hard disk.  After the
       installation is complete, pare down the operating system to a size that
       will fit onto your flash media, then tar the entire filesystem.  The
       following steps will guide you through the process of preparing a piece
@@ -249,7 +249,7 @@ pseudo-device   md              # memory disk</programlisting>
 	  <literal>165</literal>.  Now write this partition table to the disk
 	  by pressing the <keycap>w</keycap> key (this is a hidden option on
 	  this screen).  If you are using an ATA compatible compact
-	  flash card, you should choose the FreeBSD Boot Manager.  Now press
+	  flash card, you should choose the &os; Boot Manager.  Now press
 	  the <keycap>q</keycap> key to quit the partition menu.  You will be
 	  shown the boot manager menu once more - repeat the choice you made
 	  earlier.</para>
@@ -324,7 +324,7 @@ pseudo-device   md              # memory disk</programlisting>
 	<para>Assuming that you configured your filesystem correctly when it
 	  was built on the normal hard disk (with your filesystems mounted
 	  read-only, and with the necessary options compiled into the kernel)
-	  you should now be successfully booting your FreeBSD embedded
+	  you should now be successfully booting your &os; embedded
 	  system.</para>
       </step>
     </procedure>