/*
* Data structures and definitions for the CAM system.
*
* Copyright (c) 1997 Justin T. Gibbs.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
*/
#ifndef _CAM_CAM_H
#define _CAM_CAM_H 1
#ifdef _KERNEL
#include <opt_cam.h>
#endif
#include <sys/cdefs.h>
typedef u_int path_id_t;
typedef u_int target_id_t;
typedef u_int lun_id_t;
#define CAM_XPT_PATH_ID ((path_id_t)~0)
#define CAM_BUS_WILDCARD ((path_id_t)~0)
#define CAM_TARGET_WILDCARD ((target_id_t)~0)
#define CAM_LUN_WILDCARD ((lun_id_t)~0)
/*
* Maximum length for a CAM CDB.
*/
#define CAM_MAX_CDBLEN 16
/*
* Definition of a CAM peripheral driver entry. Peripheral drivers instantiate
* one of these for each device they wish to communicate with and pass it into
* the xpt layer when they wish to schedule work on that device via the
* xpt_schedule API.
*/
struct cam_periph;
/*
* Priority information for a CAM structure. The generation number is
* incremented everytime a new entry is entered into the queue giving round
* robin per priority level scheduling.
*/
typedef struct {
u_int32_t priority;
#define CAM_PRIORITY_NONE (u_int32_t)-1
u_int32_t generation;
int index;
#define CAM_UNQUEUED_INDEX -1
#define CAM_ACTIVE_INDEX -2
#define CAM_DONEQ_INDEX -3
} cam_pinfo;
/*
* Macro to compare two generation numbers. It is used like this:
*
* if (GENERATIONCMP(a, >=, b))
* ...;
*
* GERERATIONCMP uses modular arithmetic to guard against wraps
* wraps in the generation number.
*/
#define GENERATIONCMP(x, op, y) ((int32_t)((x) - (y)) op 0)
/* CAM flags */
typedef enum {
CAM_FLAG_NONE = 0x00,
CAM_EXPECT_INQ_CHANGE = 0x01
} cam_flags;
/* CAM Status field values */
typedef enum {
CAM_REQ_INPROG, /* CCB request is in progress */
CAM_REQ_CMP, /* CCB request completed without error */
CAM_REQ_ABORTED, /* CCB request aborted by the host */
CAM_UA_ABORT, /* Unable to abort CCB request */
CAM_REQ_CMP_ERR, /* CCB request completed with an error */
CAM_BUSY, /* CAM subsytem is busy */
CAM_REQ_INVALID, /* CCB request was invalid */
CAM_PATH_INVALID, /* Supplied Path ID is invalid */
CAM_DEV_NOT_THERE, /* SCSI Device Not Installed/there */
CAM_UA_TERMIO, /* Unable to terminate I/O CCB request */
CAM_SEL_TIMEOUT, /* Target Selection Timeout */
CAM_CMD_TIMEOUT, /* Command timeout */
CAM_SCSI_STATUS_ERROR, /* SCSI error, look at error code in CCB */
CAM_MSG_REJECT_REC, /* Message Reject Received */
CAM_SCSI_BUS_RESET, /* SCSI Bus Reset Sent/Received */
CAM_UNCOR_PARITY, /* Uncorrectable parity error occurred */
CAM_AUTOSENSE_FAIL = 0x10,/* Autosense: request sense cmd fail */
CAM_NO_HBA, /* No HBA Detected error */
CAM_DATA_RUN_ERR, /* Data Overrun error */
CAM_UNEXP_BUSFREE, /* Unexpected Bus Free */
CAM_SEQUENCE_FAIL, /* Target Bus Phase Sequence Failure */
CAM_CCB_LEN_ERR, /* CCB length supplied is inadequate */
CAM_PROVIDE_FAIL, /* Unable to provide requested capability */
CAM_BDR_SENT, /* A SCSI BDR msg was sent to target */
CAM_REQ_TERMIO, /* CCB request terminated by the host */
CAM_UNREC_HBA_ERROR, /* Unrecoverable Host Bus Adapter Error */
CAM_REQ_TOO_BIG, /* The request was too large for this host */
CAM_REQUEUE_REQ, /*
* This request should be requeued to preserve
* transaction ordering. This typically occurs
* when the SIM recognizes an error that should
* freeze the queue and must place additional
* requests for the target at the sim level
* back into the XPT queue.
*/
CAM_IDE = 0x33, /* Initiator Detected Error */
CAM_RESRC_UNAVAIL, /* Resource Unavailable */
CAM_UNACKED_EVENT, /* Unacknowledged Event by Host */
CAM_MESSAGE_RECV, /* Message Received in Host Target Mode */
CAM_INVALID_CDB, /* Invalid CDB received in Host Target Mode */
CAM_LUN_INVALID, /* Lun supplied is invalid */
CAM_TID_INVALID, /* Target ID supplied is invalid */
CAM_FUNC_NOTAVAIL, /* The requested function is not available */
CAM_NO_NEXUS, /* Nexus is not established */
CAM_IID_INVALID, /* The initiator ID is invalid */
CAM_CDB_RECVD, /* The SCSI CDB has been received */
CAM_LUN_ALRDY_ENA, /* The LUN is already eanbeld for target mode */
CAM_SCSI_BUSY, /* SCSI Bus Busy */
CAM_DEV_QFRZN = 0x40, /* The DEV queue is frozen w/this err */
/* Autosense data valid for target */
CAM_AUTOSNS_VALID = 0x80,
CAM_RELEASE_SIMQ = 0x100,/* SIM ready to take more commands */
CAM_SIM_QUEUED = 0x200,/* SIM has this command in it's queue */
CAM_STATUS_MASK = 0x3F, /* Mask bits for just the status # */
/* Target Specific Adjunct Status */
CAM_SENT_SENSE = 0x40000000 /* sent sense with status */
} cam_status;
__BEGIN_DECLS
typedef int (cam_quirkmatch_t)(caddr_t, caddr_t);
caddr_t cam_quirkmatch(caddr_t target, caddr_t quirk_table, int num_entries,
int entry_size, cam_quirkmatch_t *comp_func);
void cam_strvis(u_int8_t *dst, const u_int8_t *src, int srclen, int dstlen);
int cam_strmatch(const u_int8_t *str, const u_int8_t *pattern, int str_len);
__END_DECLS
#ifdef _KERNEL
static __inline void cam_init_pinfo(cam_pinfo *pinfo);
static __inline void cam_init_pinfo(cam_pinfo *pinfo)
{
pinfo->priority = CAM_PRIORITY_NONE;
pinfo->index = CAM_UNQUEUED_INDEX;
}
#endif
#endif /* _CAM_CAM_H */
