diff options
Diffstat (limited to 'sys/contrib/device-tree/Bindings/mfd')
43 files changed, 3192 insertions, 310 deletions
diff --git a/sys/contrib/device-tree/Bindings/mfd/adi,adp5585.yaml b/sys/contrib/device-tree/Bindings/mfd/adi,adp5585.yaml index ee2272f754a3..2d4ecee3f254 100644 --- a/sys/contrib/device-tree/Bindings/mfd/adi,adp5585.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/adi,adp5585.yaml @@ -15,14 +15,21 @@ description: properties: compatible: - items: - - enum: - - adi,adp5585-00 # Default - - adi,adp5585-01 # 11 GPIOs - - adi,adp5585-02 # No pull-up resistors by default on special pins - - adi,adp5585-03 # Alternate I2C address - - adi,adp5585-04 # Pull-down resistors on all pins by default - - const: adi,adp5585 + oneOf: + - items: + - enum: + - adi,adp5585-00 # Default + - adi,adp5585-01 # 11 GPIOs + - adi,adp5585-02 # No pull-up resistors by default on special pins + - adi,adp5585-03 # Alternate I2C address + - adi,adp5585-04 # Pull-down resistors on all pins by default + - const: adi,adp5585 + - items: + - enum: + - adi,adp5589-00 # Default + - adi,adp5589-01 # R4 defaulted to RESET1 output + - adi,adp5589-02 # Pull-down resistors by default on special pins + - const: adi,adp5589 reg: maxItems: 1 @@ -32,6 +39,9 @@ properties: vdd-supply: true + reset-gpios: + maxItems: 1 + gpio-controller: true '#gpio-cells': @@ -42,6 +52,84 @@ properties: "#pwm-cells": const: 3 + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + poll-interval: + enum: [10, 20, 30, 40] + default: 10 + + adi,keypad-pins: + description: Specifies the pins used for the keypad matrix. + $ref: /schemas/types.yaml#/definitions/uint32-array + + adi,unlock-events: + description: + Specifies a maximum of 2 events that can be used to unlock the keypad. + If this property is set, the keyboard will be locked and only unlocked + after these keys/gpis are pressed. The value 127 serves as a wildcard which + means any key can be used for unlocking. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 2 + items: + anyOf: + - minimum: 1 + maximum: 88 + - minimum: 97 + maximum: 115 + - const: 127 + + adi,unlock-trigger-sec: + description: + Defines the time in which the second unlock event must occur after the + first unlock event has occurred. + maximum: 7 + default: 0 + + adi,reset1-events: + description: + Defines the trigger events (key/gpi presses) that can generate reset + conditions one the reset1 block. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 3 + + adi,reset2-events: + description: + Defines the trigger events (key/gpi presses) that can generate reset + conditions one the reset2 block. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 2 + + adi,reset1-active-high: + description: Sets the reset1 signal as active high. + type: boolean + + adi,reset2-active-high: + description: Sets the reset2 signal as active high. + type: boolean + + adi,rst-passthrough-enable: + description: Allows the RST pin to override (OR with) the reset1 signal. + type: boolean + + adi,reset-trigger-ms: + description: + Defines the length of time that the reset events must be active before a + reset signal is generated. All events must be active at the same time for + the same duration. + enum: [0, 1000, 1500, 2000, 2500, 3000, 3500, 4000] + default: 0 + + adi,reset-pulse-width-us: + description: Defines the pulse width of the reset signals. + enum: [500, 1000, 2000, 10000] + default: 500 + patternProperties: "-hog(-[0-9]+)?$": type: object @@ -49,14 +137,28 @@ patternProperties: required: - gpio-hog +dependencies: + linux,keymap: + - adi,keypad-pins + - interrupts + interrupt-controller: + - interrupts + adi,unlock-trigger-sec: + - adi,unlock-events + adi,reset1-active-high: + - adi,reset1-events + adi,rst-passtrough-enable: + - adi,reset1-events + adi,reset2-active-high: + - adi,reset2-events + required: - compatible - reg - - gpio-controller - - "#gpio-cells" - - "#pwm-cells" allOf: + - $ref: /schemas/input/matrix-keymap.yaml# + - $ref: /schemas/input/input.yaml# - if: properties: compatible: @@ -64,9 +166,60 @@ allOf: const: adi,adp5585-01 then: properties: + adi,unlock-events: false + adi,unlock-trigger-sec: false gpio-reserved-ranges: false - else: + reset-gpios: false + adi,keypad-pins: + minItems: 2 + maxItems: 11 + items: + minimum: 0 + maximum: 10 + adi,reset1-events: + items: + anyOf: + - minimum: 1 + maximum: 30 + - minimum: 37 + maximum: 47 + adi,reset2-events: + items: + anyOf: + - minimum: 1 + maximum: 30 + - minimum: 37 + maximum: 47 + - if: properties: + compatible: + contains: + enum: + - adi,adp5585-00 + - adi,adp5585-02 + - adi,adp5585-03 + - adi,adp5585-04 + then: + properties: + adi,unlock-events: false + adi,unlock-trigger-sec: false + adi,keypad-pins: + minItems: 2 + maxItems: 10 + items: + enum: [0, 1, 2, 3, 4, 6, 7, 8, 9, 10] + adi,reset1-events: + items: + anyOf: + - minimum: 1 + maximum: 25 + - enum: [37, 38, 39, 40, 41, 43, 44, 45, 46, 47] + adi,reset2-events: + items: + anyOf: + - minimum: 1 + maximum: 25 + - enum: [37, 38, 39, 40, 41, 43, 44, 45, 46, 47] gpio-reserved-ranges: maxItems: 1 items: @@ -74,10 +227,44 @@ allOf: - const: 5 - const: 1 -additionalProperties: false + - if: + properties: + compatible: + contains: + enum: + - adi,adp5589-00 + - adi,adp5589-01 + - adi,adp5589-02 + then: + properties: + gpio-reserved-ranges: false + adi,keypad-pins: + minItems: 2 + maxItems: 19 + items: + minimum: 0 + maximum: 18 + adi,reset1-events: + items: + anyOf: + - minimum: 1 + maximum: 88 + - minimum: 97 + maximum: 115 + adi,reset2-events: + items: + anyOf: + - minimum: 1 + maximum: 88 + - minimum: 97 + maximum: 115 + +unevaluatedProperties: false examples: - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/irq.h> i2c { #address-cells = <1>; #size-cells = <0>; @@ -93,6 +280,33 @@ examples: gpio-reserved-ranges = <5 1>; #pwm-cells = <3>; + + interrupts = <16 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,reset1-events = <1 43>; + adi,reset2-events = <2 3>; + adi,reset-trigger-ms = <2000>; + + /* + * col0, col1, col2 + * row0, row1, row2 + */ + adi,keypad-pins = <0 1 2 6 7 8>; + + linux,keymap = < + MATRIX_KEY(0x00, 0x00, KEY_1) + MATRIX_KEY(0x00, 0x01, KEY_2) + MATRIX_KEY(0x00, 0x02, KEY_3) + + MATRIX_KEY(0x01, 0x00, KEY_A) + MATRIX_KEY(0x01, 0x01, KEY_B) + MATRIX_KEY(0x01, 0x02, KEY_C) + + MATRIX_KEY(0x02, 0x00, BTN_1) + MATRIX_KEY(0x02, 0x01, BTN_2) + MATRIX_KEY(0x02, 0x02, BTN_3) + >; }; }; diff --git a/sys/contrib/device-tree/Bindings/mfd/airoha,en7581-gpio-sysctl.yaml b/sys/contrib/device-tree/Bindings/mfd/airoha,en7581-gpio-sysctl.yaml new file mode 100644 index 000000000000..4a81ed82ef34 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/airoha,en7581-gpio-sysctl.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/airoha,en7581-gpio-sysctl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Airoha EN7581 GPIO System Controller + +maintainers: + - Christian Marangi <ansuelsmth@gmail.com> + - Lorenzo Bianconi <lorenzo@kernel.org> + +description: + Airoha EN7581 SoC GPIO system controller which provided a register map + for controlling the GPIO, pins and PWM of the SoC. + +properties: + compatible: + items: + - const: airoha,en7581-gpio-sysctl + - const: syscon + - const: simple-mfd + + reg: + maxItems: 1 + + pinctrl: + type: object + $ref: /schemas/pinctrl/airoha,en7581-pinctrl.yaml + description: + Child node definition for EN7581 Pin controller + + pwm: + type: object + $ref: /schemas/pwm/airoha,en7581-pwm.yaml + description: + Child node definition for EN7581 PWM controller + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + system-controller@1fbf0200 { + compatible = "airoha,en7581-gpio-sysctl", "syscon", "simple-mfd"; + reg = <0x1fbf0200 0xc0>; + + pinctrl { + compatible = "airoha,en7581-pinctrl"; + + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + mmc-pins { + mux { + function = "emmc"; + groups = "emmc"; + }; + }; + + mdio-pins { + mux { + function = "mdio"; + groups = "mdio"; + }; + + conf { + pins = "gpio2"; + output-enable; + }; + }; + }; + + pwm { + compatible = "airoha,en7581-pwm"; + + #pwm-cells = <3>; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/apple,smc.yaml b/sys/contrib/device-tree/Bindings/mfd/apple,smc.yaml new file mode 100644 index 000000000000..8a10e270d421 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/apple,smc.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/apple,smc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Apple Mac System Management Controller + +maintainers: + - Sven Peter <sven@kernel.org> + +description: + Apple Mac System Management Controller implements various functions + such as GPIO, RTC, power, reboot. + +properties: + compatible: + items: + - enum: + - apple,t6000-smc + - apple,t8103-smc + - apple,t8112-smc + - const: apple,smc + + reg: + items: + - description: SMC area + - description: SRAM area + + reg-names: + items: + - const: smc + - const: sram + + mboxes: + maxItems: 1 + + gpio: + $ref: /schemas/gpio/apple,smc-gpio.yaml + + reboot: + $ref: /schemas/power/reset/apple,smc-reboot.yaml + +additionalProperties: false + +required: + - compatible + - reg + - reg-names + - mboxes + +examples: + - | + soc { + #address-cells = <2>; + #size-cells = <2>; + + smc@23e400000 { + compatible = "apple,t8103-smc", "apple,smc"; + reg = <0x2 0x3e400000 0x0 0x4000>, + <0x2 0x3fe00000 0x0 0x100000>; + reg-names = "smc", "sram"; + mboxes = <&smc_mbox>; + + smc_gpio: gpio { + compatible = "apple,smc-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + reboot { + compatible = "apple,smc-reboot"; + nvmem-cells = <&shutdown_flag>, <&boot_stage>, + <&boot_error_count>, <&panic_count>; + nvmem-cell-names = "shutdown_flag", "boot_stage", + "boot_error_count", "panic_count"; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/aspeed,ast2x00-scu.yaml b/sys/contrib/device-tree/Bindings/mfd/aspeed,ast2x00-scu.yaml index 86ee69c0f45b..5eccd10d95ce 100644 --- a/sys/contrib/device-tree/Bindings/mfd/aspeed,ast2x00-scu.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/aspeed,ast2x00-scu.yaml @@ -9,6 +9,8 @@ title: Aspeed System Control Unit description: The Aspeed System Control Unit manages the global behaviour of the SoC, configuring elements such as clocks, pinmux, and reset. + In AST2700 SOC which has two soc connection, each soc have its own scu + register control, ast2700-scu0 for soc0, ast2700-scu1 for soc1. maintainers: - Joel Stanley <joel@jms.id.au> @@ -21,6 +23,8 @@ properties: - aspeed,ast2400-scu - aspeed,ast2500-scu - aspeed,ast2600-scu + - aspeed,ast2700-scu0 + - aspeed,ast2700-scu1 - const: syscon - const: simple-mfd @@ -30,7 +34,8 @@ properties: ranges: true '#address-cells': - const: 1 + minimum: 1 + maximum: 2 '#size-cells': const: 1 @@ -61,8 +66,15 @@ patternProperties: - compatible '^interrupt-controller@[0-9a-f]+$': - description: See Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2xxx-scu-ic.txt type: object + additionalProperties: true + properties: + compatible: + contains: + enum: + - aspeed,ast2500-scu-ic + - aspeed,ast2600-scu-ic0 + - aspeed,ast2600-scu-ic1 '^silicon-id@[0-9a-f]+$': description: Unique hardware silicon identifiers within the SoC @@ -76,6 +88,7 @@ patternProperties: - aspeed,ast2400-silicon-id - aspeed,ast2500-silicon-id - aspeed,ast2600-silicon-id + - aspeed,ast2700-silicon-id - const: aspeed,silicon-id reg: diff --git a/sys/contrib/device-tree/Bindings/mfd/aspeed-lpc.yaml b/sys/contrib/device-tree/Bindings/mfd/aspeed-lpc.yaml index 5dfe77aca167..d88854e60b7f 100644 --- a/sys/contrib/device-tree/Bindings/mfd/aspeed-lpc.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/aspeed-lpc.yaml @@ -1,5 +1,5 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) -# # Copyright (c) 2021 Aspeed Tehchnology Inc. +# # Copyright (c) 2021 Aspeed Technology Inc. %YAML 1.2 --- $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml# diff --git a/sys/contrib/device-tree/Bindings/mfd/atmel,at91sam9260-gpbr.yaml b/sys/contrib/device-tree/Bindings/mfd/atmel,at91sam9260-gpbr.yaml new file mode 100644 index 000000000000..f6f47999c6c1 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/atmel,at91sam9260-gpbr.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/atmel,at91sam9260-gpbr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip AT91 General Purpose Backup Registers + +maintainers: + - Nicolas Ferre <nicolas.ferre@microchip.com> + +description: + The system controller embeds 256 bits of General Purpose Backup + registers organized as 8 32-bit registers. + +properties: + compatible: + oneOf: + - items: + - enum: + - atmel,at91sam9260-gpbr + - microchip,sama7d65-gpbr + - const: syscon + - items: + - enum: + - microchip,sam9x60-gpbr + - microchip,sam9x7-gpbr + - const: atmel,at91sam9260-gpbr + - const: syscon + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + syscon@fffffd50 { + compatible = "atmel,at91sam9260-gpbr", "syscon"; + reg = <0xfffffd50 0x10>; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/atmel,at91sam9260-matrix.yaml b/sys/contrib/device-tree/Bindings/mfd/atmel,at91sam9260-matrix.yaml new file mode 100644 index 000000000000..447b3a3edbfc --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/atmel,at91sam9260-matrix.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/atmel,at91sam9260-matrix.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip AT91 Bus Matrix + +maintainers: + - Nicolas Ferre <nicolas.ferre@microchip.com> + +description: + The Bus Matrix (MATRIX) implements a multi-layer AHB, based on the + AHB-Lite protocol, that enables parallel access paths between multiple + masters and slaves in a system, thus increasing the overall bandwidth. + +properties: + compatible: + oneOf: + - items: + - enum: + - atmel,at91sam9260-matrix + - atmel,at91sam9261-matrix + - atmel,at91sam9263-matrix + - atmel,at91sam9rl-matrix + - atmel,at91sam9g45-matrix + - atmel,at91sam9n12-matrix + - atmel,at91sam9x5-matrix + - atmel,sama5d3-matrix + - const: syscon + - items: + - enum: + - microchip,sam9x60-matrix + - microchip,sam9x7-matrix + - const: atmel,at91sam9x5-matrix + - const: syscon + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + syscon@ffffec00 { + compatible = "atmel,sama5d3-matrix", "syscon"; + reg = <0xffffec00 0x200>; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/atmel,sama5d2-flexcom.yaml b/sys/contrib/device-tree/Bindings/mfd/atmel,sama5d2-flexcom.yaml index 0dc6a40b63f4..c7d6cf96796c 100644 --- a/sys/contrib/device-tree/Bindings/mfd/atmel,sama5d2-flexcom.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/atmel,sama5d2-flexcom.yaml @@ -19,12 +19,11 @@ properties: oneOf: - const: atmel,sama5d2-flexcom - items: - - const: microchip,sam9x7-flexcom + - enum: + - microchip,sam9x7-flexcom + - microchip,sama7d65-flexcom + - microchip,sama7g5-flexcom - const: atmel,sama5d2-flexcom - - items: - - const: microchip,sama7g5-flexcom - - const: atmel,sama5d2-flexcom - reg: maxItems: 1 diff --git a/sys/contrib/device-tree/Bindings/mfd/brcm,bcm59056.yaml b/sys/contrib/device-tree/Bindings/mfd/brcm,bcm59056.yaml new file mode 100644 index 000000000000..b67d7a723fc2 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/brcm,bcm59056.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/brcm,bcm59056.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM590xx Power Management Units + +maintainers: + - Artur Weber <aweber.kernel@gmail.com> + +properties: + compatible: + enum: + - brcm,bcm59054 + - brcm,bcm59056 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + regulators: + type: object + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: brcm,bcm59054 + then: + properties: + regulators: + $ref: /schemas/regulator/brcm,bcm59054.yaml# + + - if: + properties: + compatible: + contains: + const: brcm,bcm59056 + then: + properties: + regulators: + $ref: /schemas/regulator/brcm,bcm59056.yaml# + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@8 { + compatible = "brcm,bcm59056"; + reg = <0x08>; + interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>; + + regulators { + rfldo { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/fsl,mcu-mpc8349emitx.yaml b/sys/contrib/device-tree/Bindings/mfd/fsl,mcu-mpc8349emitx.yaml new file mode 100644 index 000000000000..8beb2ed9edb7 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/fsl,mcu-mpc8349emitx.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/fsl,mcu-mpc8349emitx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MPC8349E-mITX-compatible Power Management Micro Controller Unit (MCU) + +maintainers: + - J. Neuschäfer <j.ne@posteo.net> + +properties: + compatible: + oneOf: + - items: + - enum: + - fsl,mc9s08qg8-mpc8315erdb + - fsl,mc9s08qg8-mpc8349emitx + - fsl,mc9s08qg8-mpc8377erdb + - fsl,mc9s08qg8-mpc8378erdb + - fsl,mc9s08qg8-mpc8379erdb + - const: fsl,mcu-mpc8349emitx + + reg: + maxItems: 1 + + "#gpio-cells": + const: 2 + + gpio-controller: true + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + mcu@a { + #gpio-cells = <2>; + compatible = "fsl,mc9s08qg8-mpc8349emitx", + "fsl,mcu-mpc8349emitx"; + reg = <0x0a>; + gpio-controller; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/google,cros-ec.yaml b/sys/contrib/device-tree/Bindings/mfd/google,cros-ec.yaml index aac8819bd00b..50f457090066 100644 --- a/sys/contrib/device-tree/Bindings/mfd/google,cros-ec.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/google,cros-ec.yaml @@ -108,9 +108,6 @@ properties: pwm: $ref: /schemas/pwm/google,cros-ec-pwm.yaml# - kbd-led-backlight: - $ref: /schemas/chrome/google,cros-kbd-led-backlight.yaml# - keyboard-controller: $ref: /schemas/input/google,cros-ec-keyb.yaml# diff --git a/sys/contrib/device-tree/Bindings/mfd/iqs62x.yaml b/sys/contrib/device-tree/Bindings/mfd/iqs62x.yaml index e79ce447a800..f242dd0e18fd 100644 --- a/sys/contrib/device-tree/Bindings/mfd/iqs62x.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/iqs62x.yaml @@ -60,43 +60,34 @@ examples: #include <dt-bindings/interrupt-controller/irq.h> i2c { - #address-cells = <1>; - #size-cells = <0>; - - iqs620a@44 { - compatible = "azoteq,iqs620a"; - reg = <0x44>; - interrupt-parent = <&gpio>; - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; - - keys { - compatible = "azoteq,iqs620a-keys"; - - linux,keycodes = <KEY_SELECT>, - <KEY_MENU>, - <KEY_OK>, - <KEY_MENU>; - - hall-switch-south { - linux,code = <SW_LID>; - azoteq,use-prox; - }; - }; - - iqs620a_pwm: pwm { - compatible = "azoteq,iqs620a-pwm"; - #pwm-cells = <2>; - }; + #address-cells = <1>; + #size-cells = <0>; + + iqs620a@44 { + compatible = "azoteq,iqs620a"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + + keys { + compatible = "azoteq,iqs620a-keys"; + + linux,keycodes = <KEY_SELECT>, + <KEY_MENU>, + <KEY_OK>, + <KEY_MENU>; + + hall-switch-south { + linux,code = <SW_LID>; + azoteq,use-prox; + }; }; - }; - - pwmleds { - compatible = "pwm-leds"; - led-1 { - pwms = <&iqs620a_pwm 0 1000000>; - max-brightness = <255>; + iqs620a_pwm: pwm { + compatible = "azoteq,iqs620a-pwm"; + #pwm-cells = <2>; }; + }; }; - | @@ -105,37 +96,37 @@ examples: #include <dt-bindings/interrupt-controller/irq.h> i2c { - #address-cells = <1>; - #size-cells = <0>; - - iqs620a@44 { - compatible = "azoteq,iqs620a"; - reg = <0x44>; - interrupt-parent = <&gpio>; - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; - - firmware-name = "iqs620a_coil.bin"; - - keys { - compatible = "azoteq,iqs620a-keys"; - - linux,keycodes = <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <KEY_MUTE>; - - hall-switch-north { - linux,code = <SW_DOCK>; - }; - - hall-switch-south { - linux,code = <SW_TABLET_MODE>; - }; - }; + #address-cells = <1>; + #size-cells = <0>; + + iqs620a@44 { + compatible = "azoteq,iqs620a"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + + firmware-name = "iqs620a_coil.bin"; + + keys { + compatible = "azoteq,iqs620a-keys"; + + linux,keycodes = <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <KEY_MUTE>; + + hall-switch-north { + linux,code = <SW_DOCK>; + }; + + hall-switch-south { + linux,code = <SW_TABLET_MODE>; + }; }; + }; }; - | @@ -144,36 +135,36 @@ examples: #include <dt-bindings/interrupt-controller/irq.h> i2c { - #address-cells = <1>; - #size-cells = <0>; - - iqs624@44 { - compatible = "azoteq,iqs624"; - reg = <0x44>; - interrupt-parent = <&gpio>; - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; - - keys { - compatible = "azoteq,iqs624-keys"; - - linux,keycodes = <BTN_0>, - <0>, - <BTN_1>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <KEY_VOLUMEUP>, - <KEY_VOLUMEDOWN>; - }; + #address-cells = <1>; + #size-cells = <0>; + + iqs624@44 { + compatible = "azoteq,iqs624"; + reg = <0x44>; + interrupt-parent = <&gpio>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + + keys { + compatible = "azoteq,iqs624-keys"; + + linux,keycodes = <BTN_0>, + <0>, + <BTN_1>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <KEY_VOLUMEUP>, + <KEY_VOLUMEDOWN>; }; + }; }; ... diff --git a/sys/contrib/device-tree/Bindings/mfd/lp3943.txt b/sys/contrib/device-tree/Bindings/mfd/lp3943.txt index e8591d6b11b4..ca5324ed0df4 100644 --- a/sys/contrib/device-tree/Bindings/mfd/lp3943.txt +++ b/sys/contrib/device-tree/Bindings/mfd/lp3943.txt @@ -7,7 +7,7 @@ Required properties: LP3943 consists of two sub-devices, lp3943-gpio and lp3943-pwm. For the LP3943 GPIO properties please refer to: -Documentation/devicetree/bindings/gpio/gpio-lp3943.txt +Documentation/devicetree/bindings/gpio/trivial-gpio.yaml For the LP3943 PWM properties please refer to: Documentation/devicetree/bindings/pwm/pwm-lp3943.txt diff --git a/sys/contrib/device-tree/Bindings/mfd/maxim,max77705.yaml b/sys/contrib/device-tree/Bindings/mfd/maxim,max77705.yaml new file mode 100644 index 000000000000..0ec89f0adc64 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/maxim,max77705.yaml @@ -0,0 +1,158 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/maxim,max77705.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX77705 Companion Power Management and USB Type-C interface + +maintainers: + - Dzmitry Sankouski <dsankouski@gmail.com> + +description: | + This is a part of device tree bindings for Maxim MAX77705. + + Maxim MAX77705 is a Companion Power Management and Type-C + interface IC which includes charger, fuelgauge, LED, haptic motor driver and + Type-C management. + +properties: + compatible: + const: maxim,max77705 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + haptic: + type: object + additionalProperties: false + + properties: + compatible: + const: maxim,max77705-haptic + + haptic-supply: true + + pwms: + maxItems: 1 + + required: + - compatible + - haptic-supply + - pwms + + leds: + type: object + additionalProperties: false + description: + Up to 4 LED channels supported. + + properties: + compatible: + const: maxim,max77705-rgb + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + multi-led: + type: object + $ref: /schemas/leds/leds-class-multicolor.yaml# + unevaluatedProperties: false + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + patternProperties: + "^led@[0-3]$": + type: object + $ref: /schemas/leds/common.yaml# + unevaluatedProperties: false + + properties: + reg: + maxItems: 1 + + required: + - reg + + patternProperties: + "^led@[0-3]$": + type: object + $ref: /schemas/leds/common.yaml# + unevaluatedProperties: false + + properties: + reg: + maxItems: 1 + + required: + - reg + + required: + - compatible + +required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/leds/common.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@66 { + compatible = "maxim,max77705"; + reg = <0x66>; + interrupt-parent = <&pm8998_gpios>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&chg_int_default>; + pinctrl-names = "default"; + + leds { + compatible = "maxim,max77705-rgb"; + + multi-led { + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_STATUS; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_RED>; + }; + + led@2 { + reg = <2>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@3 { + reg = <3>; + color = <LED_COLOR_ID_BLUE>; + }; + }; + }; + + haptic { + compatible = "maxim,max77705-haptic"; + haptic-supply = <&vib_regulator>; + pwms = <&vib_pwm 0 50000>; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/maxim,max77759.yaml b/sys/contrib/device-tree/Bindings/mfd/maxim,max77759.yaml new file mode 100644 index 000000000000..525de9ab3c2b --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/maxim,max77759.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/maxim,max77759.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated MAX77759 PMIC for USB Type-C applications + +maintainers: + - André Draszik <andre.draszik@linaro.org> + +description: | + This is a part of device tree bindings for the MAX77759 companion Power + Management IC for USB Type-C applications. + + The MAX77759 includes Battery Charger, Fuel Gauge, temperature sensors, USB + Type-C Port Controller (TCPC), NVMEM, and a GPIO expander. + +properties: + compatible: + const: maxim,max77759 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + reg: + maxItems: 1 + + gpio: + $ref: /schemas/gpio/maxim,max77759-gpio.yaml + + nvmem-0: + $ref: /schemas/nvmem/maxim,max77759-nvmem.yaml + +required: + - compatible + - interrupts + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@66 { + compatible = "maxim,max77759"; + reg = <0x66>; + interrupts-extended = <&gpa8 3 IRQ_TYPE_LEVEL_LOW>; + + interrupt-controller; + #interrupt-cells = <2>; + + gpio { + compatible = "maxim,max77759-gpio"; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + nvmem-0 { + compatible = "maxim,max77759-nvmem"; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + reboot-mode@0 { + reg = <0x0 0x4>; + }; + + boot-reason@4 { + reg = <0x4 0x4>; + }; + + shutdown-user-flag@8 { + reg = <0x8 0x1>; + }; + + rsoc@10 { + reg = <0xa 0x2>; + }; + }; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/mediatek,mt6397.yaml b/sys/contrib/device-tree/Bindings/mfd/mediatek,mt6397.yaml new file mode 100644 index 000000000000..6a89b479d10f --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/mediatek,mt6397.yaml @@ -0,0 +1,600 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/mediatek,mt6397.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek MT6397/MT6323 PMIC + +maintainers: + - Sen Chu <sen.chu@mediatek.com> + - Macpaul Lin <macpaul.lin@mediatek.com> + +description: | + MT6397/MT6323 is a power management system chip. + Please see the sub-modules below for supported features. + + MT6397/MT6323 is a multifunction device with the following sub modules: + - Regulators + - RTC + - ADC + - Audio codec + - GPIO + - Clock + - LED + - Keys + - Power controller + + It is interfaced to host controller using SPI interface by a proprietary hardware + called PMIC wrapper or pwrap. MT6397/MT6323 PMIC is a child device of pwrap. + See the following for pwrap node definitions: + Documentation/devicetree/bindings/soc/mediatek/mediatek,pwrap.yaml + +properties: + compatible: + oneOf: + - enum: + - mediatek,mt6323 + - mediatek,mt6331 # "mediatek,mt6331" for PMIC MT6331 and MT6332. + - mediatek,mt6328 + - mediatek,mt6358 + - mediatek,mt6359 + - mediatek,mt6397 + - items: + - enum: + - mediatek,mt6366 + - const: mediatek,mt6358 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + rtc: + type: object + $ref: /schemas/rtc/rtc.yaml# + unevaluatedProperties: false + description: + MT6397 Real Time Clock. + + properties: + compatible: + oneOf: + - enum: + - mediatek,mt6323-rtc + - mediatek,mt6331-rtc + - mediatek,mt6358-rtc + - mediatek,mt6397-rtc + - items: + - enum: + - mediatek,mt6366-rtc + - const: mediatek,mt6358-rtc + + start-year: true + + required: + - compatible + + regulators: + type: object + description: + List of child nodes that specify the regulators. + additionalProperties: true + + properties: + compatible: + oneOf: + - enum: + - mediatek,mt6323-regulator + - mediatek,mt6328-regulator + - mediatek,mt6358-regulator + - mediatek,mt6359-regulator + - mediatek,mt6397-regulator + - items: + - enum: + - mediatek,mt6366-regulator + - const: mediatek,mt6358-regulator + + required: + - compatible + + adc: + type: object + $ref: /schemas/iio/adc/mediatek,mt6359-auxadc.yaml# + unevaluatedProperties: false + + audio-codec: + type: object + description: + Audio codec support with MT6358 and MT6397. + additionalProperties: true + + properties: + compatible: + oneOf: + - enum: + - mediatek,mt6358-sound + - mediatek,mt6359-codec + - mediatek,mt6397-codec + - items: + - enum: + - mediatek,mt6366-sound + - const: mediatek,mt6358-sound + + required: + - compatible + + clocks: + type: object + additionalProperties: false + description: + This is a clock buffer node for mt6397. However, there are no sub nodes + or any public document exposed in public. + + properties: + compatible: + const: mediatek,mt6397-clk + + '#clock-cells': + const: 1 + + required: + - compatible + + leds: + type: object + additionalProperties: false + description: | + MT6323 LED controller is subfunction provided by MT6323 PMIC, so the LED + controllers are defined as the subnode of the function node provided by MT6323 + PMIC controller that is being defined as one kind of Muti-Function Device (MFD) + using shared bus called PMIC wrapper for each subfunction to access remote + MT6323 PMIC hardware. + + Each led is represented as a child node of the mediatek,mt6323-led that + describes the initial behavior for each LED physically and currently only four + LED child nodes can be supported. + + properties: + compatible: + enum: + - mediatek,mt6323-led + - mediatek,mt6331-led + - mediatek,mt6332-led + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + patternProperties: + "^led@[0-3]$": + type: object + $ref: /schemas/leds/common.yaml# + unevaluatedProperties: false + + properties: + reg: + description: + LED channel number (0..3) + minimum: 0 + maximum: 3 + + required: + - reg + + required: + - compatible + - "#address-cells" + - "#size-cells" + + keys: + type: object + $ref: /schemas/input/mediatek,pmic-keys.yaml + unevaluatedProperties: false + description: + Power and Home keys. + + power-controller: + type: object + additionalProperties: false + description: + The power controller which could be found on PMIC is responsible for + externally powering off or on the remote MediaTek SoC through the + circuit BBPU (baseband power up). + + properties: + compatible: + const: mediatek,mt6323-pwrc + + '#power-domain-cells': + const: 0 + + pinctrl: + type: object + $ref: /schemas/pinctrl/mediatek,mt65xx-pinctrl.yaml + unevaluatedProperties: false + description: + Pin controller + +required: + - compatible + - regulators + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/leds/common.h> + + pmic { + compatible = "mediatek,mt6323"; + interrupt-parent = <&pio>; + interrupts = <150 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + + leds { + compatible = "mediatek,mt6323-led"; + #address-cells = <1>; + #size-cells = <0>; + }; + + regulators { + compatible = "mediatek,mt6323-regulator"; + + buck_vproc { + regulator-name = "vproc"; + regulator-min-microvolt = < 700000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-always-on; + regulator-boot-on; + }; + + buck_vsys { + regulator-name = "vsys"; + regulator-min-microvolt = <1400000>; + regulator-max-microvolt = <2987500>; + regulator-ramp-delay = <25000>; + regulator-always-on; + regulator-boot-on; + }; + + buck_vpa { + regulator-name = "vpa"; + regulator-min-microvolt = < 500000>; + regulator-max-microvolt = <3650000>; + }; + + ldo_vtcxo { + regulator-name = "vtcxo"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <90>; + regulator-always-on; + regulator-boot-on; + }; + + ldo_vcn28 { + regulator-name = "vcn28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <185>; + }; + + ldo_vcn33_bt { + regulator-name = "vcn33_bt"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3600000>; + regulator-enable-ramp-delay = <185>; + }; + + ldo_vcn33_wifi { + regulator-name = "vcn33_wifi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3600000>; + regulator-enable-ramp-delay = <185>; + }; + + ldo_va { + regulator-name = "va"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + ldo_vcama { + regulator-name = "vcama"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vio28 { + regulator-name = "vio28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + ldo_vusb { + regulator-name = "vusb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + regulator-boot-on; + }; + + ldo_vmc { + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + ldo_vmch { + regulator-name = "vmch"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + ldo_vemc3v3 { + regulator-name = "vemc3v3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + ldo_vgp1 { + regulator-name = "vgp1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vgp2 { + regulator-name = "vgp2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vgp3 { + regulator-name = "vgp3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vcn18 { + regulator-name = "vcn18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vsim1 { + regulator-name = "vsim1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vsim2 { + regulator-name = "vsim2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vrtc { + regulator-name = "vrtc"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo_vcamaf { + regulator-name = "vcamaf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vibr { + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + }; + + ldo_vrf18 { + regulator-name = "vrf18"; + regulator-min-microvolt = <1825000>; + regulator-max-microvolt = <1825000>; + regulator-enable-ramp-delay = <187>; + }; + + ldo_vm { + regulator-name = "vm"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + ldo_vio18 { + regulator-name = "vio18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + ldo_vcamd { + regulator-name = "vcamd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + ldo_vcamio { + regulator-name = "vcamio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + }; + + keys { + compatible = "mediatek,mt6323-keys"; + mediatek,long-press-mode = <1>; + power-off-time-sec = <0>; + + power { + linux,keycodes = <116>; + wakeup-source; + }; + + home { + linux,keycodes = <114>; + }; + }; + + power-controller { + compatible = "mediatek,mt6323-pwrc"; + #power-domain-cells = <0>; + }; + + rtc { + compatible = "mediatek,mt6323-rtc"; + }; + }; + + - | + #include <dt-bindings/input/input.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pmic { + compatible = "mediatek,mt6358"; + interrupt-controller; + #interrupt-cells = <2>; + + audio-codec { + compatible = "mediatek,mt6358-sound"; + Avdd-supply = <&mt6358_vaud28_reg>; + mediatek,dmic-mode = <0>; + }; + + regulators { + compatible = "mediatek,mt6358-regulator"; + + buck_vdram1 { + regulator-name = "vdram1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2087500>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <0>; + regulator-always-on; + regulator-allowed-modes = <0 1>; + }; + + // ... + + ldo_vsim2 { + regulator-name = "vsim2"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <3100000>; + regulator-enable-ramp-delay = <540>; + }; + }; + + rtc { + compatible = "mediatek,mt6358-rtc"; + }; + + keys { + compatible = "mediatek,mt6358-keys"; + + power { + linux,keycodes = <KEY_POWER>; + wakeup-source; + }; + + home { + linux,keycodes = <KEY_HOME>; + }; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pmic { + compatible = "mediatek,mt6397"; + + interrupt-parent = <&pio>; + interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + + audio-codec { + compatible = "mediatek,mt6397-codec"; + }; + + clocks { + compatible = "mediatek,mt6397-clk"; + #clock-cells = <1>; + }; + + pinctrl { + compatible = "mediatek,mt6397-pinctrl"; + gpio-controller; + #gpio-cells = <2>; + }; + + regulators { + compatible = "mediatek,mt6397-regulator"; + + buck_vpca15 { + regulator-name = "vpca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <200>; + }; + + // ... + + ldo_vibr { + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + }; + + rtc { + compatible = "mediatek,mt6397-rtc"; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/mediatek,mt8195-scpsys.yaml b/sys/contrib/device-tree/Bindings/mfd/mediatek,mt8195-scpsys.yaml index 768390b92682..0e1d43c96fb9 100644 --- a/sys/contrib/device-tree/Bindings/mfd/mediatek,mt8195-scpsys.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/mediatek,mt8195-scpsys.yaml @@ -18,6 +18,7 @@ properties: compatible: items: - enum: + - mediatek,mt6893-scpsys - mediatek,mt8167-scpsys - mediatek,mt8173-scpsys - mediatek,mt8183-scpsys diff --git a/sys/contrib/device-tree/Bindings/mfd/motorola-cpcap.txt b/sys/contrib/device-tree/Bindings/mfd/motorola-cpcap.txt index 190230216de8..18c3fc26ca93 100644 --- a/sys/contrib/device-tree/Bindings/mfd/motorola-cpcap.txt +++ b/sys/contrib/device-tree/Bindings/mfd/motorola-cpcap.txt @@ -19,7 +19,7 @@ which are described in the following files: - Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml - Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml - Documentation/devicetree/bindings/regulator/cpcap-regulator.txt -- Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt +- Documentation/devicetree/bindings/phy/motorola,cpcap-usb-phy.yaml - Documentation/devicetree/bindings/input/cpcap-pwrbutton.txt - Documentation/devicetree/bindings/rtc/cpcap-rtc.txt - Documentation/devicetree/bindings/leds/leds-cpcap.txt @@ -31,6 +31,10 @@ node must be named "audio-codec". Required properties for the audio-codec subnode: - #sound-dai-cells = <1>; +- interrupts : should contain jack detection interrupts, with headset + detect interrupt matching "hs" and microphone bias 2 + detect interrupt matching "mb2" in interrupt-names. +- interrupt-names : Contains "hs", "mb2" The audio-codec provides two DAIs. The first one is connected to the Stereo HiFi DAC and the second one is connected to the Voice DAC. @@ -52,6 +56,8 @@ Example: audio-codec { #sound-dai-cells = <1>; + interrupts-extended = <&cpcap 9 0>, <&cpcap 10 0>; + interrupt-names = "hs", "mb2"; /* HiFi */ port@0 { diff --git a/sys/contrib/device-tree/Bindings/mfd/mscc,ocelot.yaml b/sys/contrib/device-tree/Bindings/mfd/mscc,ocelot.yaml index 8bd1abfc44d9..b613da83dca4 100644 --- a/sys/contrib/device-tree/Bindings/mfd/mscc,ocelot.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/mscc,ocelot.yaml @@ -76,12 +76,6 @@ additionalProperties: false examples: - | - ocelot_clock: ocelot-clock { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <125000000>; - }; - spi { #address-cells = <1>; #size-cells = <0>; diff --git a/sys/contrib/device-tree/Bindings/mfd/mxs-lradc.yaml b/sys/contrib/device-tree/Bindings/mfd/mxs-lradc.yaml new file mode 100644 index 000000000000..782b2f4005a0 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/mxs-lradc.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/mxs-lradc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MXS Low-Resolution ADC (LRADC) + +maintainers: + - Dario Binacchi <dario.binacchi@amarulasolutions.com> + +description: + The LRADC provides 16 physical channels of 12-bit resolution for + analog-to-digital conversion and includes an integrated 4-wire/5-wire + touchscreen controller. + +properties: + compatible: + items: + - enum: + - fsl,imx23-lradc + - fsl,imx28-lradc + + reg: + maxItems: 1 + + clocks: + minItems: 1 + + interrupts: + minItems: 9 + maxItems: 13 + + fsl,lradc-touchscreen-wires: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [4, 5] + description: > + Number of wires used to connect the touchscreen to LRADC. + + If this property is not present, then the touchscreen is disabled. + + fsl,ave-ctrl: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 32 + default: 4 + description: + Number of samples per direction to calculate an average value. + + fsl,ave-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 2 + maximum: 2048 + default: 2 + description: > + Delay between consecutive samples. + + It is used if 'fsl,ave-ctrl' > 1, counts at 2 kHz and its default value (2) + is 1 ms. + + fsl,settling: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 2047 + default: 10 + description: > + Delay between plate switch to next sample. + + It counts at 2 kHz and its default (10) is 5 ms. + + "#io-channel-cells": + const: 1 + +required: + - compatible + - reg + - clocks + - interrupts + +if: + properties: + compatible: + contains: + enum: + - fsl,imx23-lradc +then: + properties: + interrupts: + items: + - description: channel 0 + - description: channel 1 + - description: channel 2 + - description: channel 3 + - description: channel 4 + - description: channel 5 + - description: touchscreen + - description: channel 6 + - description: channel 7 + fsl,lradc-touchscreen-wires: + const: 4 +else: + properties: + interrupts: + items: + - description: threshold 0 + - description: threshold 1 + - description: channel 0 + - description: channel 1 + - description: channel 2 + - description: channel 3 + - description: channel 4 + - description: channel 5 + - description: button 0 + - description: button 1 + - description: touchscreen + - description: channel 6 + - description: channel 7 + +additionalProperties: false + +examples: + - | + lradc@80050000 { + compatible = "fsl,imx23-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <36>, <37>, <38>, <39>, <40>, + <41>, <42>, <43>, <44>; + clocks = <&clks 26>; + #io-channel-cells = <1>; + fsl,lradc-touchscreen-wires = <4>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/netronix,ntxec.yaml b/sys/contrib/device-tree/Bindings/mfd/netronix,ntxec.yaml index 59a630025f52..37fbb953ea12 100644 --- a/sys/contrib/device-tree/Bindings/mfd/netronix,ntxec.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/netronix,ntxec.yaml @@ -48,29 +48,18 @@ examples: - | #include <dt-bindings/interrupt-controller/irq.h> i2c { - #address-cells = <1>; - #size-cells = <0>; - - ec: embedded-controller@43 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ntxec>; - - compatible = "netronix,ntxec"; - reg = <0x43>; - system-power-controller; - interrupt-parent = <&gpio4>; - interrupts = <11 IRQ_TYPE_EDGE_FALLING>; - #pwm-cells = <2>; - }; - }; - - backlight { - compatible = "pwm-backlight"; - pwms = <&ec 0 50000>; - power-supply = <&backlight_regulator>; - }; - - backlight_regulator: regulator-dummy { - compatible = "regulator-fixed"; - regulator-name = "backlight"; + #address-cells = <1>; + #size-cells = <0>; + + ec: embedded-controller@43 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ntxec>; + + compatible = "netronix,ntxec"; + reg = <0x43>; + system-power-controller; + interrupt-parent = <&gpio4>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + #pwm-cells = <2>; + }; }; diff --git a/sys/contrib/device-tree/Bindings/mfd/nxp,lpc1850-creg.yaml b/sys/contrib/device-tree/Bindings/mfd/nxp,lpc1850-creg.yaml new file mode 100644 index 000000000000..89b4892e9ca7 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/nxp,lpc1850-creg.yaml @@ -0,0 +1,148 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/nxp,lpc1850-creg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: The NXP LPC18xx/43xx CREG (Configuration Registers) block + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +properties: + compatible: + items: + - enum: + - nxp,lpc1850-creg + - const: syscon + - const: simple-mfd + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + clock-controller: + type: object + description: + The NXP LPC18xx/43xx CREG (Configuration Registers) block contains + control registers for two low speed clocks. One of the clocks is a + 32 kHz oscillator driver with power up/down and clock gating. Next + is a fixed divider that creates a 1 kHz clock from the 32 kHz osc. + + These clocks are used by the RTC and the Event Router peripherals. + The 32 kHz can also be routed to other peripherals to enable low + power modes. + + properties: + compatible: + const: nxp,lpc1850-creg-clk + + clocks: + maxItems: 1 + + '#clock-cells': + const: 1 + description: | + 0 1 kHz clock + 1 32 kHz Oscillator + + required: + - compatible + - clocks + - '#clock-cells' + + additionalProperties: false + + phy: + type: object + description: the internal USB OTG PHY in NXP LPC18xx and LPC43xx SoCs + properties: + compatible: + const: nxp,lpc1850-usb-otg-phy + + clocks: + maxItems: 1 + + '#phy-cells': + const: 0 + + required: + - compatible + - clocks + - '#phy-cells' + + additionalProperties: false + + dma-mux: + type: object + description: NXP LPC18xx/43xx DMA MUX (DMA request router) + properties: + compatible: + const: nxp,lpc1850-dmamux + + '#dma-cells': + const: 3 + description: | + Should be set to <3>. + * 1st cell contain the master dma request signal + * 2nd cell contain the mux value (0-3) for the peripheral + * 3rd cell contain either 1 or 2 depending on the AHB master used. + + dma-requests: + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 64 + description: Number of DMA requests the controller can handle + + dma-masters: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle pointing to the DMA controller + + required: + - compatible + - '#dma-cells' + - dma-masters + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/lpc18xx-ccu.h> + + syscon@40043000 { + compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; + reg = <0x40043000 0x1000>; + clocks = <&ccu1 CLK_CPU_CREG>; + resets = <&rgu 5>; + + clock-controller { + compatible = "nxp,lpc1850-creg-clk"; + clocks = <&xtal32>; + #clock-cells = <1>; + }; + + phy { + compatible = "nxp,lpc1850-usb-otg-phy"; + clocks = <&ccu1 CLK_USB0>; + #phy-cells = <0>; + }; + + dma-mux { + compatible = "nxp,lpc1850-dmamux"; + #dma-cells = <3>; + dma-requests = <64>; + dma-masters = <&dmac>; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/qcom,spmi-pmic.yaml b/sys/contrib/device-tree/Bindings/mfd/qcom,spmi-pmic.yaml index a2b2fbf77d5c..078a6886f8b1 100644 --- a/sys/contrib/device-tree/Bindings/mfd/qcom,spmi-pmic.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/qcom,spmi-pmic.yaml @@ -76,12 +76,14 @@ properties: - qcom,pmc8180 - qcom,pmc8180c - qcom,pmc8380 + - qcom,pmd8028 - qcom,pmd9635 - qcom,pmi632 - qcom,pmi8950 - qcom,pmi8962 - qcom,pmi8994 - qcom,pmi8998 + - qcom,pmih0108 - qcom,pmk8002 - qcom,pmk8350 - qcom,pmk8550 diff --git a/sys/contrib/device-tree/Bindings/mfd/qcom,tcsr.yaml b/sys/contrib/device-tree/Bindings/mfd/qcom,tcsr.yaml index 7d0b0b403150..14ae3f00ef7e 100644 --- a/sys/contrib/device-tree/Bindings/mfd/qcom,tcsr.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/qcom,tcsr.yaml @@ -21,6 +21,9 @@ properties: - qcom,msm8998-tcsr - qcom,qcm2290-tcsr - qcom,qcs404-tcsr + - qcom,qcs615-tcsr + - qcom,qcs8300-tcsr + - qcom,sa8255p-tcsr - qcom,sa8775p-tcsr - qcom,sc7180-tcsr - qcom,sc7280-tcsr @@ -38,7 +41,9 @@ properties: - qcom,sm8450-tcsr - qcom,tcsr-apq8064 - qcom,tcsr-apq8084 + - qcom,tcsr-ipq5018 - qcom,tcsr-ipq5332 + - qcom,tcsr-ipq5424 - qcom,tcsr-ipq6018 - qcom,tcsr-ipq8064 - qcom,tcsr-ipq8074 @@ -47,6 +52,8 @@ properties: - qcom,tcsr-msm8226 - qcom,tcsr-msm8660 - qcom,tcsr-msm8916 + - qcom,tcsr-msm8917 + - qcom,tcsr-msm8937 - qcom,tcsr-msm8953 - qcom,tcsr-msm8960 - qcom,tcsr-msm8974 diff --git a/sys/contrib/device-tree/Bindings/mfd/qnap,ts433-mcu.yaml b/sys/contrib/device-tree/Bindings/mfd/qnap,ts433-mcu.yaml new file mode 100644 index 000000000000..877078ac172f --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/qnap,ts433-mcu.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/qnap,ts433-mcu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: QNAP NAS on-board Microcontroller + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +description: + QNAP embeds a microcontroller on their NAS devices adding system feature + as PWM Fan control, additional LEDs, power button status and more. + +properties: + compatible: + enum: + - qnap,ts433-mcu + +patternProperties: + "^fan-[0-9]+$": + $ref: /schemas/hwmon/fan-common.yaml# + unevaluatedProperties: false + +required: + - compatible + +additionalProperties: false + +examples: + - | + uart { + mcu { + compatible = "qnap,ts433-mcu"; + + fan-0 { + #cooling-cells = <2>; + cooling-levels = <0 64 89 128 166 204 221 238>; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/realtek,rtl9301-switch.yaml b/sys/contrib/device-tree/Bindings/mfd/realtek,rtl9301-switch.yaml new file mode 100644 index 000000000000..f053303ab1e6 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/realtek,rtl9301-switch.yaml @@ -0,0 +1,114 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/realtek,rtl9301-switch.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek Switch with Internal CPU + +maintainers: + - Chris Packham <chris.packham@alliedtelesis.co.nz> + +description: + The RTL9300 is a series of is an Ethernet switches with an integrated CPU. A + number of different peripherals are accessed through a common register block, + represented here as a syscon node. + +properties: + compatible: + items: + - enum: + - realtek,rtl9301-switch + - realtek,rtl9302b-switch + - realtek,rtl9302c-switch + - realtek,rtl9303-switch + - const: syscon + - const: simple-mfd + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 1 + +patternProperties: + 'reboot@[0-9a-f]+$': + $ref: /schemas/power/reset/syscon-reboot.yaml# + + 'i2c@[0-9a-f]+$': + $ref: /schemas/i2c/realtek,rtl9301-i2c.yaml# + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + ethernet-switch@1b000000 { + compatible = "realtek,rtl9301-switch", "syscon", "simple-mfd"; + reg = <0x1b000000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + + reboot@c { + compatible = "syscon-reboot"; + reg = <0x0c 0x4>; + value = <0x01>; + }; + + i2c@36c { + compatible = "realtek,rtl9301-i2c"; + reg = <0x36c 0x14>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + gpio@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + + i2c@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + gpio@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; + + i2c@388 { + compatible = "realtek,rtl9301-i2c"; + reg = <0x388 0x14>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@7 { + reg = <7>; + #address-cells = <1>; + #size-cells = <0>; + gpio@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; + }; + diff --git a/sys/contrib/device-tree/Bindings/mfd/rockchip,rk806.yaml b/sys/contrib/device-tree/Bindings/mfd/rockchip,rk806.yaml index 3c2b06629b75..eb5bca31948e 100644 --- a/sys/contrib/device-tree/Bindings/mfd/rockchip,rk806.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/rockchip,rk806.yaml @@ -31,6 +31,27 @@ properties: system-power-controller: true + rockchip,reset-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + description: + Mode to use when a reset of the PMIC is triggered. + + The reset can be triggered either programmatically, via one of + the PWRCTRL pins (provided additional configuration) or + asserting RESETB pin low. + + The following modes are supported + + - 0; restart PMU, + - 1; reset all power off reset registers and force state to + switch to ACTIVE mode, + - 2; same as mode 1 and also pull RESETB pin down for 5ms, + + For example, some hardware may require a full restart (mode 0) + in order to function properly as regulators are shortly + interrupted in this mode. + vcc1-supply: description: The input supply for dcdc-reg1. diff --git a/sys/contrib/device-tree/Bindings/mfd/rohm,bd71815-pmic.yaml b/sys/contrib/device-tree/Bindings/mfd/rohm,bd71815-pmic.yaml index bb81307dc11b..4fc78efaa550 100644 --- a/sys/contrib/device-tree/Bindings/mfd/rohm,bd71815-pmic.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/rohm,bd71815-pmic.yaml @@ -50,15 +50,15 @@ properties: minimum: 0 maximum: 1 - rohm,charger-sense-resistor-ohms: - minimum: 10000000 - maximum: 50000000 + rohm,charger-sense-resistor-micro-ohms: + minimum: 10000 + maximum: 50000 description: | - BD71827 and BD71828 have SAR ADC for measuring charging currents. - External sense resistor (RSENSE in data sheet) should be used. If - something other but 30MOhm resistor is used the resistance value - should be given here in Ohms. - default: 30000000 + BD71815 has SAR ADC for measuring charging currents. External sense + resistor (RSENSE in data sheet) should be used. If something other + but a 30 mOhm resistor is used the resistance value should be given + here in micro Ohms. + default: 30000 regulators: $ref: /schemas/regulator/rohm,bd71815-regulator.yaml @@ -67,7 +67,7 @@ properties: gpio-reserved-ranges: description: | - Usage of BD71828 GPIO pins can be changed via OTP. This property can be + Usage of BD71815 GPIO pins can be changed via OTP. This property can be used to mark the pins which should not be configured for GPIO. Please see the ../gpio/gpio.txt for more information. @@ -113,7 +113,7 @@ examples: gpio-controller; #gpio-cells = <2>; - rohm,charger-sense-resistor-ohms = <10000000>; + rohm,charger-sense-resistor-micro-ohms = <10000>; regulators { buck1: buck1 { diff --git a/sys/contrib/device-tree/Bindings/mfd/rohm,bd71828-pmic.yaml b/sys/contrib/device-tree/Bindings/mfd/rohm,bd71828-pmic.yaml index fa17686a64f7..09e7d68e92bf 100644 --- a/sys/contrib/device-tree/Bindings/mfd/rohm,bd71828-pmic.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/rohm,bd71828-pmic.yaml @@ -55,14 +55,15 @@ properties: minimum: 0 maximum: 1 - rohm,charger-sense-resistor-ohms: - minimum: 10000000 - maximum: 50000000 + rohm,charger-sense-resistor-micro-ohms: + minimum: 10000 + maximum: 50000 + default: 30000 description: | BD71827 and BD71828 have SAR ADC for measuring charging currents. External sense resistor (RSENSE in data sheet) should be used. If some - other but 30MOhm resistor is used the resistance value should be given - here in Ohms. + other but 30mOhm resistor is used the resistance value should be given + here in microohms. regulators: $ref: /schemas/regulator/rohm,bd71828-regulator.yaml @@ -114,7 +115,7 @@ examples: #gpio-cells = <2>; gpio-reserved-ranges = <0 1>, <2 1>; - rohm,charger-sense-resistor-ohms = <10000000>; + rohm,charger-sense-resistor-micro-ohms = <10000>; regulators { buck1: BUCK1 { diff --git a/sys/contrib/device-tree/Bindings/mfd/rohm,bd9571mwv.yaml b/sys/contrib/device-tree/Bindings/mfd/rohm,bd9571mwv.yaml index 534cf03f36bb..47611c2a982c 100644 --- a/sys/contrib/device-tree/Bindings/mfd/rohm,bd9571mwv.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/rohm,bd9571mwv.yaml @@ -99,29 +99,29 @@ examples: #include <dt-bindings/interrupt-controller/irq.h> i2c { - #address-cells = <1>; - #size-cells = <0>; - - pmic: pmic@30 { - compatible = "rohm,bd9571mwv"; - reg = <0x30>; - interrupt-parent = <&gpio2>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-controller; - #gpio-cells = <2>; - rohm,ddr-backup-power = <0xf>; - rohm,rstbmode-pulse; - - regulators { - dvfs: dvfs { - regulator-name = "dvfs"; - regulator-min-microvolt = <750000>; - regulator-max-microvolt = <1030000>; - regulator-boot-on; - regulator-always-on; - }; - }; - }; + #address-cells = <1>; + #size-cells = <0>; + + pmic: pmic@30 { + compatible = "rohm,bd9571mwv"; + reg = <0x30>; + interrupt-parent = <&gpio2>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + rohm,ddr-backup-power = <0xf>; + rohm,rstbmode-pulse; + + regulators { + dvfs: dvfs { + regulator-name = "dvfs"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1030000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; }; diff --git a/sys/contrib/device-tree/Bindings/mfd/rohm,bd96801-pmic.yaml b/sys/contrib/device-tree/Bindings/mfd/rohm,bd96801-pmic.yaml index efee3de0d9ad..0e06570483ae 100644 --- a/sys/contrib/device-tree/Bindings/mfd/rohm,bd96801-pmic.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/rohm,bd96801-pmic.yaml @@ -4,19 +4,21 @@ $id: http://devicetree.org/schemas/mfd/rohm,bd96801-pmic.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: ROHM BD96801 Scalable Power Management Integrated Circuit +title: ROHM BD96801/BD96805 Scalable Power Management Integrated Circuit maintainers: - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> description: - BD96801 is an automotive grade single-chip power management IC. - It integrates 4 buck converters and 3 LDOs with safety features like + BD96801 and BD96805 are automotive grade, single-chip power management ICs. + They both integrate 4 buck converters and 3 LDOs with safety features like over-/under voltage and over current detection and a watchdog. properties: compatible: - const: rohm,bd96801 + enum: + - rohm,bd96801 + - rohm,bd96805 reg: maxItems: 1 diff --git a/sys/contrib/device-tree/Bindings/mfd/rohm,bd96802-pmic.yaml b/sys/contrib/device-tree/Bindings/mfd/rohm,bd96802-pmic.yaml new file mode 100644 index 000000000000..6cbea796d12f --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/rohm,bd96802-pmic.yaml @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/rohm,bd96802-pmic.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BD96802 / BD96806 Scalable Power Management Integrated Circuit + +maintainers: + - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> + +description: | + BD96802Qxx-C and BD96806 are automotive grade configurable Power Management + Integrated Circuits supporting Functional Safety features for application + processors, SoCs and FPGAs + +properties: + compatible: + enum: + - rohm,bd96802 + - rohm,bd96806 + + reg: + maxItems: 1 + + interrupts: + description: + The PMIC provides intb and errb IRQ lines. The errb IRQ line is used + for fatal IRQs which will cause the PMIC to shut down power outputs. + In many systems this will shut down the SoC contolling the PMIC and + connecting/handling the errb can be omitted. However, there are cases + where the SoC is not powered by the PMIC or has a short time backup + energy to handle shutdown of critical hardware. In that case it may be + useful to connect the errb and handle errb events. + minItems: 1 + maxItems: 2 + + interrupt-names: + minItems: 1 + items: + - enum: [intb, errb] + - const: errb + + regulators: + $ref: ../regulator/rohm,bd96802-regulator.yaml + description: + List of child nodes that specify the regulators. + +required: + - compatible + - reg + - interrupts + - interrupt-names + - regulators + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/leds/common.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + pmic: pmic@62 { + reg = <0x62>; + compatible = "rohm,bd96802"; + interrupt-parent = <&gpio1>; + interrupts = <29 IRQ_TYPE_LEVEL_LOW>, <6 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "intb", "errb"; + + regulators { + buck1 { + regulator-name = "buck1"; + regulator-ramp-delay = <1250>; + /* 0.5V min INITIAL - 150 mV tune */ + regulator-min-microvolt = <350000>; + /* 3.3V + 150mV tune */ + regulator-max-microvolt = <3450000>; + + /* These can be set only when PMIC is in STBY */ + rohm,initial-voltage-microvolt = <500000>; + regulator-ov-error-microvolt = <230000>; + regulator-uv-error-microvolt = <230000>; + regulator-temp-protection-kelvin = <1>; + regulator-temp-warn-kelvin = <0>; + }; + buck2 { + regulator-name = "buck2"; + regulator-min-microvolt = <350000>; + regulator-max-microvolt = <3450000>; + + rohm,initial-voltage-microvolt = <3000000>; + regulator-ov-error-microvolt = <18000>; + regulator-uv-error-microvolt = <18000>; + regulator-temp-protection-kelvin = <1>; + regulator-temp-warn-kelvin = <1>; + }; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/samsung,s2dos05.yaml b/sys/contrib/device-tree/Bindings/mfd/samsung,s2dos05.yaml new file mode 100644 index 000000000000..b85285720c16 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/samsung,s2dos05.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/samsung,s2dos05.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S2DOS05 Power Management IC + +maintainers: + - Dzmitry Sankouski <dsankouski@gmail.com> + +description: + This is a device tree bindings for S2DOS family of Power Management IC (PMIC). + + The S2DOS05 is a companion power management IC for the panel and touchscreen + in smart phones. Provides voltage regulators and + ADC for power/current measurements. + + Regulator section has 4 LDO and 1 BUCK regulators and also + provides ELVDD, ELVSS, AVDD lines. + +properties: + compatible: + const: samsung,s2dos05 + + reg: + maxItems: 1 + + regulators: + patternProperties: + "^buck|ldo[1-4]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + required: + - regulator-name + + additionalProperties: false + +required: + - compatible + - reg + - regulators + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@60 { + compatible = "samsung,s2dos05"; + reg = <0x60>; + + regulators { + ldo1 { + regulator-active-discharge = <1>; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2000000>; + regulator-name = "ldo1"; + }; + + ldo2 { + regulator-active-discharge = <1>; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "ldo2"; + }; + + ldo3 { + regulator-active-discharge = <1>; + regulator-boot-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "ldo3"; + }; + + ldo4 { + regulator-active-discharge = <1>; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3775000>; + regulator-name = "ldo4"; + }; + + buck { + regulator-active-discharge = <1>; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <2100000>; + regulator-name = "buck"; + }; + }; + }; + }; + +... diff --git a/sys/contrib/device-tree/Bindings/mfd/samsung,s2mps11.yaml b/sys/contrib/device-tree/Bindings/mfd/samsung,s2mps11.yaml index a4be642de33c..31d544a9c05c 100644 --- a/sys/contrib/device-tree/Bindings/mfd/samsung,s2mps11.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/samsung,s2mps11.yaml @@ -20,11 +20,13 @@ description: | properties: compatible: enum: + - samsung,s2mpg10-pmic - samsung,s2mps11-pmic - samsung,s2mps13-pmic - samsung,s2mps14-pmic - samsung,s2mps15-pmic - samsung,s2mpu02-pmic + - samsung,s2mpu05-pmic clocks: $ref: /schemas/clock/samsung,s2mps11.yaml @@ -57,11 +59,12 @@ properties: reset (setting buck voltages to default values). type: boolean + system-power-controller: true + wakeup-source: true required: - compatible - - reg - regulators additionalProperties: false @@ -71,6 +74,31 @@ allOf: properties: compatible: contains: + const: samsung,s2mpg10-pmic + then: + properties: + reg: false + samsung,s2mps11-acokb-ground: false + samsung,s2mps11-wrstbi-ground: false + + # oneOf is required, because dtschema's fixups.py doesn't handle this + # nesting here. Its special treatment to allow either interrupt property + # when only one is specified in the binding works at the top level only. + oneOf: + - required: [interrupts] + - required: [interrupts-extended] + + else: + properties: + system-power-controller: false + + required: + - reg + + - if: + properties: + compatible: + contains: const: samsung,s2mps11-pmic then: properties: @@ -125,6 +153,18 @@ allOf: samsung,s2mps11-acokb-ground: false samsung,s2mps11-wrstbi-ground: false + - if: + properties: + compatible: + contains: + const: samsung,s2mpu05-pmic + then: + properties: + regulators: + $ref: /schemas/regulator/samsung,s2mpu05.yaml + samsung,s2mps11-acokb-ground: false + samsung,s2mps11-wrstbi-ground: false + examples: - | #include <dt-bindings/interrupt-controller/irq.h> diff --git a/sys/contrib/device-tree/Bindings/mfd/sprd,sc2731.yaml b/sys/contrib/device-tree/Bindings/mfd/sprd,sc2731.yaml new file mode 100644 index 000000000000..b023e1ef8d3c --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/sprd,sc2731.yaml @@ -0,0 +1,244 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/sprd,sc2731.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Spreadtrum SC27xx PMIC + +maintainers: + - Orson Zhai <orsonzhai@gmail.com> + - Baolin Wang <baolin.wang7@gmail.com> + - Chunyan Zhang <zhang.lyra@gmail.com> + +description: | + Spreadtrum PMICs belonging to the SC27xx series integrate all mobile handset + power management, audio codec, battery management and user interface support + functions in a single chip. They have 6 major functional blocks: + - DCDCs to support CPU, memory + - LDOs to support both internal and external requirements + - Battery management system, such as charger, fuel gauge + - Audio codec + - User interface functions, such as indicator, flash LED and so on + - IC level interface, such as power on/off control, RTC, typec and so on + +properties: + $nodename: + pattern: '^pmic@[0-9a-f]+$' + + compatible: + enum: + - sprd,sc2720 + - sprd,sc2721 + - sprd,sc2723 + - sprd,sc2730 + - sprd,sc2731 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + spi-max-frequency: true + + '#address-cells': + const: 1 + + '#interrupt-cells': + const: 1 + + '#size-cells': + const: 0 + + regulators: + type: object + $ref: /schemas/regulator/sprd,sc2731-regulator.yaml# + +patternProperties: + "^adc@[0-9a-f]+$": + type: object + $ref: /schemas/iio/adc/sprd,sc2720-adc.yaml# + + "^charger@[0-9a-f]+$": + type: object + $ref: /schemas/power/supply/sc2731-charger.yaml# + + "^efuse@[0-9a-f]+$": + type: object + $ref: /schemas/nvmem/sprd,sc2731-efuse.yaml# + + "^fuel-gauge@[0-9a-f]+$": + type: object + $ref: /schemas/power/supply/sc27xx-fg.yaml# + + "^gpio@[0-9a-f]+$": + type: object + $ref: /schemas/gpio/sprd,gpio-eic.yaml# + + "^led-controller@[0-9a-f]+$": + type: object + $ref: /schemas/leds/sprd,sc2731-bltc.yaml# + + "^rtc@[0-9a-f]+$": + type: object + $ref: /schemas/rtc/sprd,sc2731-rtc.yaml# + + "^vibrator@[0-9a-f]+$": + type: object + $ref: /schemas/input/sprd,sc27xx-vibrator.yaml# + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - spi-max-frequency + - '#address-cells' + - '#interrupt-cells' + - '#size-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/leds/common.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + sc2731_pmic: pmic@0 { + compatible = "sprd,sc2731"; + reg = <0>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + spi-max-frequency = <26000000>; + #address-cells = <1>; + #interrupt-cells = <1>; + #size-cells = <0>; + + charger@0 { + compatible = "sprd,sc2731-charger"; + reg = <0x0>; + phys = <&ssphy>; + monitored-battery = <&bat>; + }; + + led-controller@200 { + compatible = "sprd,sc2731-bltc"; + reg = <0x200>; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0x0>; + color = <LED_COLOR_ID_RED>; + }; + + led@1 { + reg = <0x1>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@2 { + reg = <0x2>; + color = <LED_COLOR_ID_BLUE>; + }; + }; + + rtc@280 { + compatible = "sprd,sc2731-rtc"; + reg = <0x280>; + interrupt-parent = <&sc2731_pmic>; + interrupts = <2>; + }; + + pmic_eic: gpio@300 { + compatible = "sprd,sc2731-eic"; + reg = <0x300>; + interrupt-parent = <&sc2731_pmic>; + interrupts = <5>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + efuse@380 { + compatible = "sprd,sc2731-efuse"; + reg = <0x380>; + hwlocks = <&hwlock 12>; + #address-cells = <1>; + #size-cells = <1>; + + /* Data cells */ + fgu_calib: calib@6 { + reg = <0x6 0x2>; + bits = <0 9>; + }; + + adc_big_scale: calib@24 { + reg = <0x24 0x2>; + }; + + adc_small_scale: calib@26 { + reg = <0x26 0x2>; + }; + }; + + pmic_adc: adc@480 { + compatible = "sprd,sc2731-adc"; + reg = <0x480>; + interrupt-parent = <&sc2731_pmic>; + interrupts = <0>; + #io-channel-cells = <1>; + hwlocks = <&hwlock 4>; + nvmem-cells = <&adc_big_scale>, <&adc_small_scale>; + nvmem-cell-names = "big_scale_calib", "small_scale_calib"; + }; + + fuel-gauge@a00 { + compatible = "sprd,sc2731-fgu"; + reg = <0xa00>; + battery-detect-gpios = <&pmic_eic 9 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&sc2731_pmic>; + interrupts = <4>; + io-channels = <&pmic_adc 5>, <&pmic_adc 14>; + io-channel-names = "bat-temp", "charge-vol"; + nvmem-cells = <&fgu_calib>; + nvmem-cell-names = "fgu_calib"; + monitored-battery = <&bat>; + sprd,calib-resistance-micro-ohms = <21500>; + }; + + vibrator@ec8 { + compatible = "sprd,sc2731-vibrator"; + reg = <0xec8>; + }; + + regulators { + compatible = "sprd,sc2731-regulator"; + + BUCK_CPU0 { + regulator-name = "vddarm0"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1996875>; + regulator-ramp-delay = <25000>; + regulator-always-on; + }; + + LDO_CAMA0 { + regulator-name = "vddcama0"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + regulator-enable-ramp-delay = <100>; + }; + }; + }; + }; +... diff --git a/sys/contrib/device-tree/Bindings/mfd/st,stm32-lptimer.yaml b/sys/contrib/device-tree/Bindings/mfd/st,stm32-lptimer.yaml index d41308856408..4eabafb8079d 100644 --- a/sys/contrib/device-tree/Bindings/mfd/st,stm32-lptimer.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/st,stm32-lptimer.yaml @@ -21,7 +21,12 @@ maintainers: properties: compatible: - const: st,stm32-lptimer + oneOf: + - items: + - const: st,stm32mp25-lptimer + - const: st,stm32-lptimer + - items: + - const: st,stm32-lptimer reg: maxItems: 1 @@ -48,13 +53,21 @@ properties: minItems: 1 maxItems: 2 + power-domains: + maxItems: 1 + pwm: type: object additionalProperties: false properties: compatible: - const: st,stm32-pwm-lp + oneOf: + - items: + - const: st,stm32mp25-pwm-lp + - const: st,stm32-pwm-lp + - items: + - const: st,stm32-pwm-lp "#pwm-cells": const: 3 @@ -69,7 +82,12 @@ properties: properties: compatible: - const: st,stm32-lptimer-counter + oneOf: + - items: + - const: st,stm32mp25-lptimer-counter + - const: st,stm32-lptimer-counter + - items: + - const: st,stm32-lptimer-counter required: - compatible @@ -80,7 +98,12 @@ properties: properties: compatible: - const: st,stm32-lptimer-timer + oneOf: + - items: + - const: st,stm32mp25-lptimer-timer + - const: st,stm32-lptimer-timer + - items: + - const: st,stm32-lptimer-timer required: - compatible @@ -92,13 +115,18 @@ patternProperties: properties: compatible: - const: st,stm32-lptimer-trigger + oneOf: + - items: + - const: st,stm32mp25-lptimer-trigger + - const: st,stm32-lptimer-trigger + - items: + - const: st,stm32-lptimer-trigger reg: description: Identify trigger hardware block. items: minimum: 0 - maximum: 2 + maximum: 4 required: - compatible diff --git a/sys/contrib/device-tree/Bindings/mfd/st,stm32-timers.yaml b/sys/contrib/device-tree/Bindings/mfd/st,stm32-timers.yaml index b0e438ff4950..66aa1550a4e5 100644 --- a/sys/contrib/device-tree/Bindings/mfd/st,stm32-timers.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/st,stm32-timers.yaml @@ -21,7 +21,9 @@ maintainers: properties: compatible: - const: st,stm32-timers + enum: + - st,stm32-timers + - st,stm32mp25-timers reg: maxItems: 1 @@ -36,6 +38,9 @@ properties: resets: maxItems: 1 + power-domains: + maxItems: 1 + dmas: minItems: 1 maxItems: 7 @@ -77,7 +82,9 @@ properties: properties: compatible: - const: st,stm32-pwm + enum: + - st,stm32-pwm + - st,stm32mp25-pwm "#pwm-cells": const: 3 @@ -113,7 +120,9 @@ properties: properties: compatible: - const: st,stm32-timer-counter + enum: + - st,stm32-timer-counter + - st,stm32mp25-timer-counter required: - compatible @@ -128,12 +137,13 @@ patternProperties: enum: - st,stm32-timer-trigger - st,stm32h7-timer-trigger + - st,stm32mp25-timer-trigger reg: description: Identify trigger hardware block. items: minimum: 0 - maximum: 16 + maximum: 19 required: - compatible diff --git a/sys/contrib/device-tree/Bindings/mfd/syscon.yaml b/sys/contrib/device-tree/Bindings/mfd/syscon.yaml index cc9b17ad69f2..27672adeb1fe 100644 --- a/sys/contrib/device-tree/Bindings/mfd/syscon.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/syscon.yaml @@ -27,7 +27,8 @@ select: compatible: contains: enum: - - al,alpine-sysfabric-servic + - airoha,en7581-pbus-csr + - al,alpine-sysfabric-service - allwinner,sun8i-a83t-system-controller - allwinner,sun8i-h3-system-controller - allwinner,sun8i-v3s-system-controller @@ -83,17 +84,23 @@ select: - mediatek,mt2701-pctl-a-syscfg - mediatek,mt2712-pctl-a-syscfg - mediatek,mt6397-pctl-pmic-syscfg + - mediatek,mt7988-topmisc - mediatek,mt8135-pctl-a-syscfg - mediatek,mt8135-pctl-b-syscfg - mediatek,mt8173-pctl-a-syscfg - mediatek,mt8365-syscfg - microchip,lan966x-cpu-syscon + - microchip,mpfs-sysreg-scb - microchip,sam9x60-sfr + - microchip,sama7d65-ddr3phy + - microchip,sama7d65-sfrbu - microchip,sama7g5-ddr3phy - mscc,ocelot-cpu-syscon - mstar,msc313-pmsleep - nuvoton,ma35d1-sys - nuvoton,wpcm450-shm + - qcom,apq8064-mmss-sfpb + - qcom,apq8064-sps-sic - rockchip,px30-qos - rockchip,rk3036-qos - rockchip,rk3066-qos @@ -102,6 +109,8 @@ select: - rockchip,rk3288-qos - rockchip,rk3368-qos - rockchip,rk3399-qos + - rockchip,rk3528-qos + - rockchip,rk3562-qos - rockchip,rk3568-qos - rockchip,rk3576-qos - rockchip,rk3588-qos @@ -124,6 +133,7 @@ properties: compatible: items: - enum: + - airoha,en7581-pbus-csr - al,alpine-sysfabric-service - allwinner,sun8i-a83t-system-controller - allwinner,sun8i-h3-system-controller @@ -180,17 +190,24 @@ properties: - mediatek,mt2701-pctl-a-syscfg - mediatek,mt2712-pctl-a-syscfg - mediatek,mt6397-pctl-pmic-syscfg + - mediatek,mt7988-topmisc - mediatek,mt8135-pctl-a-syscfg - mediatek,mt8135-pctl-b-syscfg - mediatek,mt8173-pctl-a-syscfg + - mediatek,mt8365-infracfg-nao - mediatek,mt8365-syscfg - microchip,lan966x-cpu-syscon + - microchip,mpfs-sysreg-scb - microchip,sam9x60-sfr + - microchip,sama7d65-ddr3phy + - microchip,sama7d65-sfrbu - microchip,sama7g5-ddr3phy - mscc,ocelot-cpu-syscon - mstar,msc313-pmsleep - nuvoton,ma35d1-sys - nuvoton,wpcm450-shm + - qcom,apq8064-mmss-sfpb + - qcom,apq8064-sps-sic - rockchip,px30-qos - rockchip,rk3036-qos - rockchip,rk3066-qos @@ -199,6 +216,8 @@ properties: - rockchip,rk3288-qos - rockchip,rk3368-qos - rockchip,rk3399-qos + - rockchip,rk3528-qos + - rockchip,rk3562-qos - rockchip,rk3568-qos - rockchip,rk3576-qos - rockchip,rk3588-qos @@ -211,6 +230,7 @@ properties: - ti,am625-dss-oldi-io-ctrl - ti,am62p-cpsw-mac-efuse - ti,am654-dss-oldi-io-ctrl + - ti,j784s4-acspcie-proxy-ctrl - ti,j784s4-pcie-ctrl - ti,keystone-pllctrl - const: syscon diff --git a/sys/contrib/device-tree/Bindings/mfd/ti,tps65910.yaml b/sys/contrib/device-tree/Bindings/mfd/ti,tps65910.yaml new file mode 100644 index 000000000000..a2668fc30a7b --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/ti,tps65910.yaml @@ -0,0 +1,318 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/ti,tps65910.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI TPS65910 Power Management Integrated Circuit + +maintainers: + - Shree Ramamoorthy <s-ramamoorthy@ti.com> + +description: + TPS65910 device is a Power Management IC that provides 3 step-down converters, + 1 stepup converter, and 8 LDOs. The device contains an embedded power controller (EPC), + 1 GPIO, and an RTC. + +properties: + compatible: + enum: + - ti,tps65910 + - ti,tps65911 + + reg: + description: I2C slave address + maxItems: 1 + + gpio-controller: true + + '#gpio-cells': + const: 2 + description: | + The first cell is the GPIO number. + The second cell is used to specify additional options <unused>. + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + description: Specifies the IRQ number and flags + const: 2 + + ti,vmbch-threshold: + description: | + (TPS65911) Main battery charged threshold comparator. + See VMBCH_VSEL in TPS65910 datasheet. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + + ti,vmbch2-threshold: + description: | + (TPS65911) Main battery discharged threshold comparator. + See VMBCH_VSEL in TPS65910 datasheet. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + + ti,en-ck32k-xtal: + type: boolean + description: Enable external 32-kHz crystal oscillator. + + ti,en-gpio-sleep: + description: | + Enable sleep control for gpios. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 9 + maxItems: 9 + items: + minimum: 0 + maximum: 1 + + ti,system-power-controller: + type: boolean + description: Identify whether or not this pmic controls the system power + + ti,sleep-enable: + type: boolean + description: Enable SLEEP state. + + ti,sleep-keep-therm: + type: boolean + description: Keep thermal monitoring on in sleep state. + + ti,sleep-keep-ck32k: + type: boolean + description: Keep the 32KHz clock output on in sleep state. + + ti,sleep-keep-hsclk: + type: boolean + description: Keep high speed internal clock on in sleep state. + + regulators: + type: object + additionalProperties: false + description: List of regulators provided by this controller. + + patternProperties: + "^(vrtc|vio|vpll|vdac|vmmc|vbb|vddctrl)$": + type: object + $ref: /schemas/regulator/regulator.yaml# + properties: + ti,regulator-ext-sleep-control: + description: | + Enable external sleep control through external inputs: + [0 (not enabled), 1 (EN1), 2 (EN2) or 4(EN3)]. + If this property is not defined, it defaults to 0 (not enabled). + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 4, 8] + unevaluatedProperties: false + + "^(vdd[1-3]|vaux([1-2]|33)|vdig[1-2])$": + type: object + $ref: /schemas/regulator/regulator.yaml# + properties: + ti,regulator-ext-sleep-control: + description: | + Enable external sleep control through external inputs: + [0 (not enabled), 1 (EN1), 2 (EN2) or 4(EN3)]. + If this property is not defined, it defaults to 0 (not enabled). + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 4, 8] + unevaluatedProperties: false + + "^ldo[1-8]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + properties: + ti,regulator-ext-sleep-control: + description: | + Enable external sleep control through external inputs: + [0 (not enabled), 1 (EN1), 2 (EN2) or 4(EN3)]. + If this property is not defined, it defaults to 0 (not enabled). + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 4, 8] + unevaluatedProperties: false + +patternProperties: + "^(vcc(io|[1-7])-supply)$": + description: | + Input voltage supply phandle for regulators. + These entries are required if PMIC regulators are enabled, or else it + can cause the regulator registration to fail. + + If some input supply is powered through battery or always-on supply, then + it is also required to have these parameters with the proper node handle for always-on + power supply. + tps65910: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: VAUX33 and VMMC input. + vcc4-supply: VAUX1 and VAUX2 input. + vcc5-supply: VPLL and VDAC input. + vcc6-supply: VDIG1 and VDIG2 input. + vcc7-supply: VRTC and VBB input. + vccio-supply: VIO input. + tps65911: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: LDO6, LDO7 and LDO8 input. + vcc4-supply: LDO5 input. + vcc5-supply: LDO3 and LDO4 input. + vcc6-supply: LDO1 and LDO2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - regulators + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - ti,tps65910 + then: + properties: + regulators: + patternProperties: + "^(ldo[1-8]|vddctrl)$": false + - if: + properties: + compatible: + contains: + enum: + - ti,tps65911 + then: + properties: + regulators: + patternProperties: + "^(vdd3|vaux([1-2]|33)|vdig[1-2])$": false + "^(vpll|vdac|vmmc|vbb)$": false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic: tps65910@2d { + compatible = "ti,tps65910"; + reg = <0x2d>; + interrupt-parent = <&intc>; + interrupts = < 0 118 0x04 >; + + #gpio-cells = <2>; + gpio-controller; + + #interrupt-cells = <2>; + interrupt-controller; + + ti,system-power-controller; + + ti,vmbch-threshold = <0>; + ti,vmbch2-threshold = <0>; + ti,en-ck32k-xtal; + ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; + + vcc1-supply = <®_parent>; + vcc2-supply = <&some_reg>; + vcc3-supply = <&vbat>; + vcc4-supply = <&vbat>; + vcc5-supply = <&vbat>; + vcc6-supply = <&vbat>; + vcc7-supply = <&vbat>; + vccio-supply = <&vbat>; + + regulators { + vio_reg: vio { + regulator-name = "vio"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + vdd1_reg: vdd1 { + regulator-name = "vdd1"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <0>; + }; + vdd2_reg: vdd2 { + regulator-name = "vdd2"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + vdd3_reg: vdd3 { + regulator-name = "vdd3"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + vdig1_reg: vdig1 { + regulator-name = "vdig1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2700000>; + regulator-always-on; + }; + vdig2_reg: vdig2 { + regulator-name = "vdig2"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + vpll_reg: vpll { + regulator-name = "vpll"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + vdac_reg: vdac { + regulator-name = "vdac"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + vaux1_reg: vaux1 { + regulator-name = "vaux1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + vaux2_reg: vaux2 { + regulator-name = "vaux2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + vaux33_reg: vaux33 { + regulator-name = "vaux33"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + vmmc_reg: vmmc { + regulator-name = "vmmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/ti,tps6594.yaml b/sys/contrib/device-tree/Bindings/mfd/ti,tps6594.yaml index 6341b6070366..a48cb00afe43 100644 --- a/sys/contrib/device-tree/Bindings/mfd/ti,tps6594.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/ti,tps6594.yaml @@ -22,6 +22,7 @@ properties: - ti,tps6593-q1 - ti,tps6594-q1 - ti,tps65224-q1 + - ti,tps652g1 reg: description: I2C slave address or SPI chip select number. diff --git a/sys/contrib/device-tree/Bindings/mfd/ti,twl.yaml b/sys/contrib/device-tree/Bindings/mfd/ti,twl.yaml index e94b0fd7af0f..f162ab60c09b 100644 --- a/sys/contrib/device-tree/Bindings/mfd/ti,twl.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/ti,twl.yaml @@ -54,7 +54,7 @@ allOf: $ref: /schemas/iio/adc/ti,twl4030-madc.yaml unevaluatedProperties: false - bci: + charger: type: object $ref: /schemas/power/supply/twl4030-charger.yaml unevaluatedProperties: false @@ -105,6 +105,11 @@ allOf: regulator-initial-mode: false properties: + charger: + type: object + properties: + compatible: + const: ti,twl6030-charger gpadc: type: object properties: @@ -136,6 +141,13 @@ allOf: regulator-initial-mode: false properties: + charger: + type: object + properties: + compatible: + items: + - const: ti,twl6032-charger + - const: ti,twl6030-charger gpadc: type: object properties: @@ -169,6 +181,14 @@ properties: "#clock-cells": const: 1 + charger: + type: object + additionalProperties: true + properties: + compatible: true + required: + - compatible + rtc: type: object additionalProperties: false @@ -222,6 +242,14 @@ examples: interrupt-controller; #interrupt-cells = <1>; + charger { + compatible = "ti,twl6030-charger"; + interrupts = <2>, <5>; + io-channels = <&gpadc 10>; + io-channel-names = "vusb"; + monitored-battery = <&bat>; + }; + gpadc { compatible = "ti,twl6030-gpadc"; interrupts = <6>; @@ -259,7 +287,7 @@ examples: interrupt-controller; #interrupt-cells = <1>; - bci { + charger { compatible = "ti,twl4030-bci"; interrupts = <9>, <2>; bci3v1-supply = <&vusb3v1>; diff --git a/sys/contrib/device-tree/Bindings/mfd/x-powers,axp152.yaml b/sys/contrib/device-tree/Bindings/mfd/x-powers,axp152.yaml index 14ab367fc887..45f015d63df1 100644 --- a/sys/contrib/device-tree/Bindings/mfd/x-powers,axp152.yaml +++ b/sys/contrib/device-tree/Bindings/mfd/x-powers,axp152.yaml @@ -71,6 +71,7 @@ allOf: - x-powers,axp15060 - x-powers,axp305 - x-powers,axp313a + - x-powers,axp323 then: required: @@ -82,6 +83,7 @@ allOf: contains: enum: - x-powers,axp313a + - x-powers,axp323 - x-powers,axp15060 - x-powers,axp717 @@ -100,6 +102,7 @@ properties: - x-powers,axp221 - x-powers,axp223 - x-powers,axp313a + - x-powers,axp323 - x-powers,axp717 - x-powers,axp803 - x-powers,axp806 @@ -313,106 +316,106 @@ additionalProperties: false examples: - | - i2c { - #address-cells = <1>; - #size-cells = <0>; - - pmic@30 { - compatible = "x-powers,axp152"; - reg = <0x30>; - interrupts = <0>; - interrupt-controller; - #interrupt-cells = <1>; - }; - }; + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@30 { + compatible = "x-powers,axp152"; + reg = <0x30>; + interrupts = <0>; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; - | - #include <dt-bindings/interrupt-controller/irq.h> - - i2c { - #address-cells = <1>; - #size-cells = <0>; - - pmic@34 { - compatible = "x-powers,axp209"; - reg = <0x34>; - interrupt-parent = <&nmi_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <1>; - - ac_power_supply: ac-power { - compatible = "x-powers,axp202-ac-power-supply"; - }; - - axp_adc: adc { - compatible = "x-powers,axp209-adc"; - #io-channel-cells = <1>; - }; - - axp_gpio: gpio { - compatible = "x-powers,axp209-gpio"; - gpio-controller; - #gpio-cells = <2>; - - gpio0-adc-pin { - pins = "GPIO0"; - function = "adc"; - }; - }; - - battery_power_supply: battery-power { - compatible = "x-powers,axp209-battery-power-supply"; - }; - - regulators { - /* Default work frequency for buck regulators */ - x-powers,dcdc-freq = <1500>; - - reg_dcdc2: dcdc2 { - regulator-always-on; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1450000>; - regulator-name = "vdd-cpu"; - }; - - reg_dcdc3: dcdc3 { - regulator-always-on; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1400000>; - regulator-name = "vdd-int-dll"; - }; - - reg_ldo1: ldo1 { - /* LDO1 is a fixed output regulator */ - regulator-always-on; - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1300000>; - regulator-name = "vdd-rtc"; - }; - - reg_ldo2: ldo2 { - regulator-always-on; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-name = "avcc"; - }; - - reg_ldo3: ldo3 { - regulator-name = "ldo3"; - }; - - reg_ldo4: ldo4 { - regulator-name = "ldo4"; - }; - - reg_ldo5: ldo5 { - regulator-name = "ldo5"; - }; - }; - - usb_power_supply: usb-power { - compatible = "x-powers,axp202-usb-power-supply"; - }; - }; - }; + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + ac_power_supply: ac-power { + compatible = "x-powers,axp202-ac-power-supply"; + }; + + axp_adc: adc { + compatible = "x-powers,axp209-adc"; + #io-channel-cells = <1>; + }; + + axp_gpio: gpio { + compatible = "x-powers,axp209-gpio"; + gpio-controller; + #gpio-cells = <2>; + + gpio0-adc-pin { + pins = "GPIO0"; + function = "adc"; + }; + }; + + battery_power_supply: battery-power { + compatible = "x-powers,axp209-battery-power-supply"; + }; + + regulators { + /* Default work frequency for buck regulators */ + x-powers,dcdc-freq = <1500>; + + reg_dcdc2: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdc3: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; + }; + + reg_ldo1: ldo1 { + /* LDO1 is a fixed output regulator */ + regulator-always-on; + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-rtc"; + }; + + reg_ldo2: ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; + }; + + reg_ldo3: ldo3 { + regulator-name = "ldo3"; + }; + + reg_ldo4: ldo4 { + regulator-name = "ldo4"; + }; + + reg_ldo5: ldo5 { + regulator-name = "ldo5"; + }; + }; + + usb_power_supply: usb-power { + compatible = "x-powers,axp202-usb-power-supply"; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/mfd/zii,rave-sp.yaml b/sys/contrib/device-tree/Bindings/mfd/zii,rave-sp.yaml new file mode 100644 index 000000000000..1d078c5ef168 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/mfd/zii,rave-sp.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/zii,rave-sp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Zodiac Inflight Innovations RAVE Supervisory Processor + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +description: + RAVE Supervisory Processor communicates with SoC over UART. It is + expected that its Device Tree node is specified as a child of a node + corresponding to UART controller used for communication. + +properties: + compatible: + enum: + - zii,rave-sp-niu + - zii,rave-sp-mezz + - zii,rave-sp-esb + - zii,rave-sp-rdu1 + - zii,rave-sp-rdu2 + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + watchdog: + $ref: /schemas/watchdog/zii,rave-sp-wdt.yaml + + backlight: + $ref: /schemas/leds/backlight/zii,rave-sp-backlight.yaml + + pwrbutton: + $ref: /schemas/input/zii,rave-sp-pwrbutton.yaml + +patternProperties: + '^eeprom@[0-9a-f]+$': + $ref: /schemas/nvmem/zii,rave-sp-eeprom.yaml + +required: + - compatible + +allOf: + - $ref: /schemas/serial/serial-peripheral-props.yaml + +unevaluatedProperties: false + +examples: + - | + mfd { + compatible = "zii,rave-sp-rdu2"; + current-speed = <1000000>; + + watchdog { + compatible = "zii,rave-sp-watchdog"; + }; + }; + |