diff options
Diffstat (limited to 'sys/contrib/device-tree/Bindings/regulator')
21 files changed, 784 insertions, 52 deletions
diff --git a/sys/contrib/device-tree/Bindings/regulator/adi,adp5055-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/adi,adp5055-regulator.yaml new file mode 100644 index 000000000000..9c4ead4c9fd1 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/regulator/adi,adp5055-regulator.yaml @@ -0,0 +1,157 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/adi,adp5055-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADP5055 Triple Buck Regulator + +maintainers: + - Alexis Czezar Torreno <alexisczezar.torreno@analog.com> + +description: | + The ADP5055 combines three high performance buck regulator. The device enables + direct connection to high input voltages up to 18 V with no preregulators. + https://www.analog.com/media/en/technical-documentation/data-sheets/adp5055.pdf + +properties: + compatible: + enum: + - adi,adp5055 + + reg: + enum: + - 0x70 + - 0x71 + + adi,tset-us: + description: + Setting time used by the device. This is changed via soldering specific + resistor values on the CFG2 pin. + enum: [2600, 20800] + default: 2600 + + adi,ocp-blanking: + description: + If present, overcurrent protection (OCP) blanking for all regulator is on. + type: boolean + + adi,delay-power-good: + description: + Configures delay timer of the power good (PWRGD) pin. Delay is based on + Tset which can be 2.6 ms or 20.8 ms. + type: boolean + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + '^buck[0-2]$': + type: object + $ref: regulator.yaml# + unevaluatedProperties: false + + properties: + enable-gpios: + maxItems: 1 + description: + GPIO specifier to enable the GPIO control for each regulator. The + driver supports two modes of enable, hardware only (GPIOs) or software + only (Registers). Pure hardware enabling requires each regulator to + contain this property. If at least one regulator does not have this, + the driver automatically switches to software only mode. + + adi,dvs-limit-upper-microvolt: + description: + Configure the allowable upper side limit of the voltage output of each + regulator in microvolt. Relative to the default Vref trimming value. + Vref = 600 mV. Voltages are in 12 mV steps, value is autoadjusted. + Vout_high = Vref_trim + dvs-limit-upper. + minimum: 12000 + maximum: 192000 + default: 192000 + + adi,dvs-limit-lower-microvolt: + description: + Configure the allowable lower side limit of the voltage output of each + regulator in microvolt. Relative to the default Vref trimming value. + Vref = 600 mV. Voltages are in 12 mV steps, value is autoadjusted. + Vout_low = Vref_trim + dvs-limit-lower. + minimum: -190500 + maximum: -10500 + default: -190500 + + adi,fast-transient: + description: + Configures the fast transient sensitivity for each regulator. + "none" - No fast transient. + "3G_1.5%" - 1.5% window with 3*350uA/V + "5G_1.5%" - 1.5% window with 5*350uA/V + "5G_2.5%" - 2.5% window with 5*350uA/V + enum: [none, 3G_1.5%, 5G_1.5%, 5G_2.5%] + default: 5G_2.5% + + adi,mask-power-good: + description: + If present, masks individual regulators PWRGD signal to the external + PWRGD hardware pin. + type: boolean + + required: + - regulator-name + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + regulator@70 { + compatible = "adi,adp5055"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + adi,tset-us = <2600>; + adi,ocp-blanking; + adi,delay-power-good; + + buck0 { + regulator-name = "buck0"; + enable-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + adi,dvs-limit-upper-microvolt = <192000>; + adi,dvs-limit-lower-microvolt = <(-190500)>; + adi,fast-transient = "5G_2.5%"; + adi,mask-power-good; + }; + + buck1 { + regulator-name = "buck1"; + enable-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; + adi,dvs-limit-upper-microvolt = <192000>; + adi,dvs-limit-lower-microvolt = <(-190500)>; + adi,fast-transient = "5G_2.5%"; + adi,mask-power-good; + }; + + buck2 { + regulator-name = "buck2"; + enable-gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; + adi,dvs-limit-upper-microvolt = <192000>; + adi,dvs-limit-lower-microvolt = <(-190500)>; + adi,fast-transient = "5G_2.5%"; + adi,mask-power-good; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/regulator/brcm,bcm59054.yaml b/sys/contrib/device-tree/Bindings/regulator/brcm,bcm59054.yaml new file mode 100644 index 000000000000..5b46d7fca05e --- /dev/null +++ b/sys/contrib/device-tree/Bindings/regulator/brcm,bcm59054.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/brcm,bcm59054.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM59054 Power Management Unit regulators + +description: | + This is a part of device tree bindings for the BCM59054 power + management unit. + + See Documentation/devicetree/bindings/mfd/brcm,bcm59056.yaml for + additional information and example. + +maintainers: + - Artur Weber <aweber.kernel@gmail.com> + +patternProperties: + "^(cam|sim|mmc)ldo[1-2]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^(rf|sd|sdx|aud|mic|usb|vib|tcx)ldo$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^(c|mm|v)sr$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^(io|sd)sr[1-2]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^gpldo[1-3]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^lvldo[1-2]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + +properties: + vbus: + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + +additionalProperties: false diff --git a/sys/contrib/device-tree/Bindings/regulator/brcm,bcm59056.yaml b/sys/contrib/device-tree/Bindings/regulator/brcm,bcm59056.yaml new file mode 100644 index 000000000000..7a5e36394d21 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/regulator/brcm,bcm59056.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/brcm,bcm59056.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM59056 Power Management Unit regulators + +description: | + This is a part of device tree bindings for the BCM59056 power + management unit. + + See Documentation/devicetree/bindings/mfd/brcm,bcm59056.yaml for + additional information and example. + +maintainers: + - Artur Weber <aweber.kernel@gmail.com> + +patternProperties: + "^(cam|sim|mmc)ldo[1-2]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^(rf|sd|sdx|aud|mic|usb|vib)ldo$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^(c|m|v)sr$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^(io|sd)sr[1-2]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + "^gpldo[1-6]$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + +properties: + vbus: + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + +additionalProperties: false diff --git a/sys/contrib/device-tree/Bindings/regulator/infineon,ir38060.yaml b/sys/contrib/device-tree/Bindings/regulator/infineon,ir38060.yaml index e6ffbc2a2298..57ff6bf1e188 100644 --- a/sys/contrib/device-tree/Bindings/regulator/infineon,ir38060.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/infineon,ir38060.yaml @@ -7,7 +7,7 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: Infineon Buck Regulators with PMBUS interfaces maintainers: - - Not Me. + - Guenter Roeck <linux@roeck-us.net> allOf: - $ref: regulator.yaml# diff --git a/sys/contrib/device-tree/Bindings/regulator/lltc,ltc3676.yaml b/sys/contrib/device-tree/Bindings/regulator/lltc,ltc3676.yaml new file mode 100644 index 000000000000..f47eacf96cd6 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/regulator/lltc,ltc3676.yaml @@ -0,0 +1,167 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/lltc,ltc3676.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Linear Technology LTC3676 8-output regulators + +maintainers: + - Tim Harvey <tharvey@gateworks.com> + +description: | + LTC3676 contains eight regulators, 4 switching SW1..SW4 and four LDO1..4 . + +properties: + compatible: + const: lltc,ltc3676 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + regulators: + type: object + additionalProperties: false + description: | + List of regulators provided by this controller, must be named + after their hardware counterparts (SW|LDO)[1-4]. + + patternProperties: + "^(sw[1-4]|ldo[24])$": + type: object + unevaluatedProperties: false + $ref: regulator.yaml# + description: + Properties for single SW or LDO regulator. Regulators SW1..SW4 can + regulate the feedback reference from 412.5mV to 800mV in 12.5 mV + steps. The output voltage thus ranges between 0.4125 * (1 + R1/R2) V + and 0.8 * (1 + R1/R2) V. + Regulators LDO1, LDO2, LDO4 have a fixed 0.725 V reference and thus + output 0.725 * (1 + R1/R2) V. + The LDO1 standby regulator can not be disabled and thus should have + the regulator-always-on property set. + + properties: + lltc,fb-voltage-divider: + description: + An array of two integers containing the resistor values + R1 and R2 of the feedback voltage divider in ohms. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + + required: + - lltc,fb-voltage-divider + + properties: + ldo1: + type: object + unevaluatedProperties: false + $ref: regulator.yaml# + description: + The LDO1 standby regulator can not be disabled and thus should + have the regulator-always-on property set. See patternProperties + description above for the rest of the details. + + properties: + lltc,fb-voltage-divider: + description: + An array of two integers containing the resistor values + R1 and R2 of the feedback voltage divider in ohms. + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + + required: + - lltc,fb-voltage-divider + - regulator-always-on + + ldo3: + type: object + unevaluatedProperties: false + $ref: regulator.yaml# + description: + The LDO3 regulator is fixed to 1.8 V. See patternProperties + description above for the rest of the details. + +required: + - compatible + - reg + - regulators + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@3c { + compatible = "lltc,ltc3676"; + reg = <0x3c>; + + regulators { + sw1_reg: sw1 { + regulator-min-microvolt = <674400>; + regulator-max-microvolt = <1308000>; + lltc,fb-voltage-divider = <127000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <1033310>; + regulator-max-microvolt = <200400>; + lltc,fb-voltage-divider = <301000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-min-microvolt = <674400>; + regulator-max-microvolt = <130800>; + lltc,fb-voltage-divider = <127000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <868310>; + regulator-max-microvolt = <168400>; + lltc,fb-voltage-divider = <221000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-min-microvolt = <2490375>; + regulator-max-microvolt = <2490375>; + lltc,fb-voltage-divider = <487000 200000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + regulator-min-microvolt = <3023250>; + regulator-max-microvolt = <3023250>; + lltc,fb-voltage-divider = <634000 200000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; + }; diff --git a/sys/contrib/device-tree/Bindings/regulator/mediatek,mt6357-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/mediatek,mt6357-regulator.yaml index 6327bb2f6ee0..698266c09e25 100644 --- a/sys/contrib/device-tree/Bindings/regulator/mediatek,mt6357-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/mediatek,mt6357-regulator.yaml @@ -33,7 +33,7 @@ patternProperties: "^ldo-v(camio18|aud28|aux18|io18|io28|rf12|rf18|cn18|cn28|fe28)$": type: object - $ref: fixed-regulator.yaml# + $ref: regulator.yaml# unevaluatedProperties: false description: Properties for single fixed LDO regulator. @@ -112,7 +112,6 @@ examples: regulator-enable-ramp-delay = <220>; }; mt6357_vfe28_reg: ldo-vfe28 { - compatible = "regulator-fixed"; regulator-name = "vfe28"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; @@ -125,14 +124,12 @@ examples: regulator-enable-ramp-delay = <110>; }; mt6357_vrf18_reg: ldo-vrf18 { - compatible = "regulator-fixed"; regulator-name = "vrf18"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-enable-ramp-delay = <110>; }; mt6357_vrf12_reg: ldo-vrf12 { - compatible = "regulator-fixed"; regulator-name = "vrf12"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; @@ -157,14 +154,12 @@ examples: regulator-enable-ramp-delay = <264>; }; mt6357_vcn28_reg: ldo-vcn28 { - compatible = "regulator-fixed"; regulator-name = "vcn28"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-enable-ramp-delay = <264>; }; mt6357_vcn18_reg: ldo-vcn18 { - compatible = "regulator-fixed"; regulator-name = "vcn18"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -183,7 +178,6 @@ examples: regulator-enable-ramp-delay = <264>; }; mt6357_vcamio_reg: ldo-vcamio18 { - compatible = "regulator-fixed"; regulator-name = "vcamio"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -212,28 +206,24 @@ examples: regulator-always-on; }; mt6357_vaux18_reg: ldo-vaux18 { - compatible = "regulator-fixed"; regulator-name = "vaux18"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-enable-ramp-delay = <264>; }; mt6357_vaud28_reg: ldo-vaud28 { - compatible = "regulator-fixed"; regulator-name = "vaud28"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-enable-ramp-delay = <264>; }; mt6357_vio28_reg: ldo-vio28 { - compatible = "regulator-fixed"; regulator-name = "vio28"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-enable-ramp-delay = <264>; }; mt6357_vio18_reg: ldo-vio18 { - compatible = "regulator-fixed"; regulator-name = "vio18"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; diff --git a/sys/contrib/device-tree/Bindings/regulator/mediatek,mt6873-dvfsrc-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/mediatek,mt6873-dvfsrc-regulator.yaml index 704828687970..685ccf9cf4d4 100644 --- a/sys/contrib/device-tree/Bindings/regulator/mediatek,mt6873-dvfsrc-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/mediatek,mt6873-dvfsrc-regulator.yaml @@ -17,9 +17,11 @@ properties: compatible: enum: - mediatek,mt6873-dvfsrc-regulator + - mediatek,mt6893-dvfsrc-regulator - mediatek,mt8183-dvfsrc-regulator - mediatek,mt8192-dvfsrc-regulator - mediatek,mt8195-dvfsrc-regulator + - mediatek,mt8196-dvfsrc-regulator dvfsrc-vcore: description: DVFSRC-controlled SoC Vcore regulator diff --git a/sys/contrib/device-tree/Bindings/regulator/mt6315-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/mt6315-regulator.yaml index cd4aa27218a1..fa6743bb269d 100644 --- a/sys/contrib/device-tree/Bindings/regulator/mt6315-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/mt6315-regulator.yaml @@ -35,10 +35,6 @@ properties: $ref: regulator.yaml# unevaluatedProperties: false - properties: - regulator-compatible: - pattern: "^vbuck[1-4]$" - additionalProperties: false required: @@ -56,7 +52,6 @@ examples: regulators { vbuck1 { - regulator-compatible = "vbuck1"; regulator-min-microvolt = <300000>; regulator-max-microvolt = <1193750>; regulator-enable-ramp-delay = <256>; @@ -64,7 +59,6 @@ examples: }; vbuck3 { - regulator-compatible = "vbuck3"; regulator-min-microvolt = <300000>; regulator-max-microvolt = <1193750>; regulator-enable-ramp-delay = <256>; diff --git a/sys/contrib/device-tree/Bindings/regulator/nxp,pca9450-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/nxp,pca9450-regulator.yaml index f8057bba747a..a5486c36830f 100644 --- a/sys/contrib/device-tree/Bindings/regulator/nxp,pca9450-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/nxp,pca9450-regulator.yaml @@ -17,6 +17,9 @@ description: | Datasheet is available at https://www.nxp.com/docs/en/data-sheet/PCA9450DS.pdf + Support PF9453, Datasheet is available at + https://www.nxp.com/docs/en/data-sheet/PF9453_SDS.pdf + # The valid names for PCA9450 regulator nodes are: # BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, # LDO1, LDO2, LDO3, LDO4, LDO5 @@ -29,6 +32,8 @@ properties: - nxp,pca9450b - nxp,pca9450c - nxp,pca9451a + - nxp,pca9452 + - nxp,pf9453 reg: maxItems: 1 @@ -41,8 +46,30 @@ properties: description: | list of regulators provided by this controller + properties: + LDO5: + type: object + $ref: regulator.yaml# + description: + Properties for single LDO5 regulator. + + properties: + nxp,sd-vsel-fixed-low: + type: boolean + description: + Let the driver know that SD_VSEL is hardwired to low level and + there is no GPIO to get the actual value from. + + sd-vsel-gpios: + description: + GPIO that can be used to read the current status of the SD_VSEL + signal in order for the driver to know if LDO5CTRL_L or LDO5CTRL_H + is used by the hardware. + + unevaluatedProperties: false + patternProperties: - "^LDO[1-5]$": + "^LDO([1-4]|-SNVS)$": type: object $ref: regulator.yaml# description: @@ -73,15 +100,19 @@ properties: PMIC default "STANDBY" state voltage in uV. Only Buck1~3 have such dvs(dynamic voltage scaling) property. + regulator-allowed-modes: + description: | + Buck regulator operating modes allowed. Valid values below. + Users should use the macros from dt-bindings/regulator/nxp,pca9450-regulator.h + 0 (PCA9450_BUCK_MODE_AUTO): Auto PFM/PWM mode + 1 (PCA9450_BUCK_MODE_FORCE_PWM): Forced PWM mode + items: + enum: [ 0, 1 ] + unevaluatedProperties: false additionalProperties: false - sd-vsel-gpios: - description: GPIO that is used to switch LDO5 between being configured by - LDO5CTRL_L or LDO5CTRL_H register. Use this if the SD_VSEL signal is - connected to a host GPIO. - nxp,i2c-lt-enable: type: boolean description: @@ -100,9 +131,28 @@ required: additionalProperties: false +allOf: + - if: + properties: + compatible: + contains: + const: nxp,pf9453 + then: + properties: + regulators: + patternProperties: + "^LDO[3-4]$": false + "^BUCK[5-6]$": false + else: + properties: + regulators: + properties: + LDO-SNVS: false + examples: - | #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/regulator/nxp,pca9450-regulator.h> i2c { #address-cells = <1>; @@ -139,6 +189,8 @@ examples: regulator-max-microvolt = <3400000>; regulator-boot-on; regulator-always-on; + regulator-initial-mode = <PCA9450_BUCK_MODE_FORCE_PWM>; + regulator-allowed-modes = <PCA9450_BUCK_MODE_FORCE_PWM>; }; buck5: BUCK5 { regulator-name = "BUCK5"; @@ -146,6 +198,8 @@ examples: regulator-max-microvolt = <3400000>; regulator-boot-on; regulator-always-on; + regulator-allowed-modes = <PCA9450_BUCK_MODE_AUTO + PCA9450_BUCK_MODE_FORCE_PWM>; }; buck6: BUCK6 { regulator-name = "BUCK6"; diff --git a/sys/contrib/device-tree/Bindings/regulator/qcom,qca6390-pmu.yaml b/sys/contrib/device-tree/Bindings/regulator/qcom,qca6390-pmu.yaml index 11ed04c95542..47c425c9fff1 100644 --- a/sys/contrib/device-tree/Bindings/regulator/qcom,qca6390-pmu.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/qcom,qca6390-pmu.yaml @@ -18,6 +18,7 @@ properties: compatible: enum: - qcom,qca6390-pmu + - qcom,wcn6750-pmu - qcom,wcn6855-pmu - qcom,wcn7850-pmu @@ -27,15 +28,27 @@ properties: vddaon-supply: description: VDD_AON supply regulator handle + vddasd-supply: + description: VDD_ASD supply regulator handle + vdddig-supply: description: VDD_DIG supply regulator handle vddpmu-supply: description: VDD_PMU supply regulator handle + vddpmumx-supply: + description: VDD_PMU_MX supply regulator handle + + vddpmucx-supply: + description: VDD_PMU_CX supply regulator handle + vddio1p2-supply: description: VDD_IO_1P2 supply regulator handle + vddrfa0p8-supply: + description: VDD_RFA_0P8 supply regulator handle + vddrfa0p95-supply: description: VDD_RFA_0P95 supply regulator handle @@ -45,12 +58,18 @@ properties: vddrfa1p3-supply: description: VDD_RFA_1P3 supply regulator handle + vddrfa1p7-supply: + description: VDD_RFA_1P7 supply regulator handle + vddrfa1p8-supply: description: VDD_RFA_1P8 supply regulator handle vddrfa1p9-supply: description: VDD_RFA_1P9 supply regulator handle + vddrfa2p2-supply: + description: VDD_RFA_2P2 supply regulator handle + vddpcie1p3-supply: description: VDD_PCIE_1P3 supply regulator handle @@ -72,6 +91,10 @@ properties: maxItems: 1 description: GPIO line indicating the state of the clock supply to the BT module + xo-clk-gpios: + maxItems: 1 + description: GPIO line allowing to select the XO clock configuration for the module + clocks: maxItems: 1 description: Reference clock handle @@ -113,12 +136,28 @@ allOf: properties: compatible: contains: + const: qcom,wcn6750-pmu + then: + required: + - vddaon-supply + - vddasd-supply + - vddpmu-supply + - vddrfa0p8-supply + - vddrfa1p2-supply + - vddrfa1p7-supply + - vddrfa2p2-supply + - if: + properties: + compatible: + contains: const: qcom,wcn6855-pmu then: required: - vddio-supply - vddaon-supply - vddpmu-supply + - vddpmumx-supply + - vddpmucx-supply - vddrfa0p95-supply - vddrfa1p3-supply - vddrfa1p9-supply diff --git a/sys/contrib/device-tree/Bindings/regulator/qcom,rpmh-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/qcom,rpmh-regulator.yaml index 27c6d5152413..4c5b0629aa3e 100644 --- a/sys/contrib/device-tree/Bindings/regulator/qcom,rpmh-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/qcom,rpmh-regulator.yaml @@ -40,6 +40,7 @@ description: | For PM660, smps1 - smps6, ldo1 - ldo3, ldo5 - ldo19 For PM660L, smps1 - smps3, smps5, ldo1 - ldo8, bob For PM7325, smps1 - smps8, ldo1 - ldo19 + For PM7550, smps1 - smps6, ldo1 - ldo23, bob For PM8005, smps1 - smps4 For PM8009, smps1 - smps2, ldo1 - ldo7 For PM8010, ldo1 - ldo7 @@ -53,6 +54,7 @@ description: | For PMI8998, bob For PMC8380, smps1 - smps8, ldo1 - lodo3 For PMR735A, smps1 - smps3, ldo1 - ldo7 + For PMR735B, ldo1 - ldo12 For PMX55, smps1 - smps7, ldo1 - ldo16 For PMX65, smps1 - smps8, ldo1 - ldo21 For PMX75, smps1 - smps10, ldo1 - ldo21 @@ -66,6 +68,7 @@ properties: - qcom,pm660-rpmh-regulators - qcom,pm660l-rpmh-regulators - qcom,pm7325-rpmh-regulators + - qcom,pm7550-rpmh-regulators - qcom,pm8005-rpmh-regulators - qcom,pm8009-rpmh-regulators - qcom,pm8009-1-rpmh-regulators @@ -87,6 +90,7 @@ properties: - qcom,pmm8155au-rpmh-regulators - qcom,pmm8654au-rpmh-regulators - qcom,pmr735a-rpmh-regulators + - qcom,pmr735b-rpmh-regulators - qcom,pmx55-rpmh-regulators - qcom,pmx65-rpmh-regulators - qcom,pmx75-rpmh-regulators @@ -222,6 +226,25 @@ allOf: properties: compatible: enum: + - qcom,pm7550-rpmh-regulators + then: + properties: + vdd-bob-supply: + description: BOB regulator parent supply phandle. + vdd-l2-l3-supply: true + vdd-l4-l5-supply: true + vdd-l9-l10-supply: true + vdd-l12-l14-supply: true + vdd-l13-l16-supply: true + vdd-l15-l17-l18-l19-l20-l21-l22-l23-supply: true + patternProperties: + "^vdd-l(1|[6-8]|11)-supply$": true + "^vdd-s[1-6]-supply$": true + + - if: + properties: + compatible: + enum: - qcom,pm8005-rpmh-regulators then: patternProperties: @@ -349,7 +372,6 @@ allOf: properties: compatible: enum: - - qcom,pm8550ve-rpmh-regulators - qcom,pm8550vs-rpmh-regulators then: patternProperties: @@ -385,6 +407,7 @@ allOf: compatible: enum: - qcom,pmc8380-rpmh-regulators + - qcom,pm8550ve-rpmh-regulators then: patternProperties: "^vdd-l[1-3]-supply$": true @@ -428,6 +451,18 @@ allOf: properties: compatible: enum: + - qcom,pmr735b-rpmh-regulators + then: + properties: + vdd-l1-l2-supply: true + vdd-l7-l8-supply: true + patternProperties: + "^vdd-l([3-6]|9|1[0-2])-supply$": true + + - if: + properties: + compatible: + enum: - qcom,pmx55-rpmh-regulators then: properties: diff --git a/sys/contrib/device-tree/Bindings/regulator/qcom,smd-rpm-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/qcom,smd-rpm-regulator.yaml index f2fd2df68a9e..b7241ce975b9 100644 --- a/sys/contrib/device-tree/Bindings/regulator/qcom,smd-rpm-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/qcom,smd-rpm-regulator.yaml @@ -22,7 +22,7 @@ description: Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. - For mp5496, s1, s2 + For mp5496, s1, s2, l2, l5 For pm2250, s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, l21, l22 diff --git a/sys/contrib/device-tree/Bindings/regulator/qcom-labibb-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/qcom-labibb-regulator.yaml index e987c39b223e..83965076d6ab 100644 --- a/sys/contrib/device-tree/Bindings/regulator/qcom-labibb-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/qcom-labibb-regulator.yaml @@ -16,7 +16,12 @@ description: properties: compatible: - const: qcom,pmi8998-lab-ibb + oneOf: + - const: qcom,pmi8998-lab-ibb + - items: + - enum: + - qcom,pmi8950-lab-ibb + - const: qcom,pmi8998-lab-ibb lab: type: object diff --git a/sys/contrib/device-tree/Bindings/regulator/raspberrypi,7inch-touchscreen-panel-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/raspberrypi,7inch-touchscreen-panel-regulator.yaml index 41678400e63f..18944d39d08f 100644 --- a/sys/contrib/device-tree/Bindings/regulator/raspberrypi,7inch-touchscreen-panel-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/raspberrypi,7inch-touchscreen-panel-regulator.yaml @@ -12,14 +12,17 @@ maintainers: description: | The RaspberryPi 7" display has an ATTINY88-based regulator/backlight controller on the PCB, which is used to turn the display unit on/off - and control the backlight. + and control the backlight. The V2 supports 5" and 7" panels and also + offers PWM backlight control. allOf: - $ref: regulator.yaml# properties: compatible: - const: raspberrypi,7inch-touchscreen-panel-regulator + enum: + - raspberrypi,7inch-touchscreen-panel-regulator + - raspberrypi,touchscreen-panel-regulator-v2 reg: maxItems: 1 diff --git a/sys/contrib/device-tree/Bindings/regulator/regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/regulator.yaml index 1ef380d1515e..77573bcb6b79 100644 --- a/sys/contrib/device-tree/Bindings/regulator/regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/regulator.yaml @@ -34,6 +34,9 @@ properties: regulator-input-current-limit-microamp: description: maximum input current regulator allows + regulator-power-budget-milliwatt: + description: power budget of the regulator + regulator-always-on: description: boolean, regulator should never be disabled type: boolean diff --git a/sys/contrib/device-tree/Bindings/regulator/richtek,rtq2208.yaml b/sys/contrib/device-tree/Bindings/regulator/richtek,rtq2208.yaml index 87accc6f13b8..022c1f197364 100644 --- a/sys/contrib/device-tree/Bindings/regulator/richtek,rtq2208.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/richtek,rtq2208.yaml @@ -39,7 +39,7 @@ properties: interrupts: maxItems: 1 - + richtek,mtp-sel-high: type: boolean description: @@ -77,6 +77,7 @@ properties: properties: richtek,fixed-microvolt: + deprecated: true description: | This property can be used to set a fixed operating voltage that lies outside the range of the regulator's adjustable mode. diff --git a/sys/contrib/device-tree/Bindings/regulator/rohm,bd96802-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/rohm,bd96802-regulator.yaml new file mode 100644 index 000000000000..671eaf1096d3 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/regulator/rohm,bd96802-regulator.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/rohm,bd96802-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BD96802 Power Management Integrated Circuit regulators + +maintainers: + - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> + +description: + This module is part of the ROHM BD96802 MFD device. For more details + see Documentation/devicetree/bindings/mfd/rohm,bd96802-pmic.yaml. + + The regulator controller is represented as a sub-node of the PMIC node + on the device tree. + + Regulator nodes should be named to buck1 and buck2. + +patternProperties: + "^buck[1-2]$": + type: object + description: + Properties for single BUCK regulator. + $ref: regulator.yaml# + + properties: + rohm,initial-voltage-microvolt: + description: + Initial voltage for regulator. Voltage can be tuned +/-150 mV from + this value. NOTE, This can be modified via I2C only when PMIC is in + STBY state. + minimum: 500000 + maximum: 3300000 + + rohm,keep-on-stby: + description: + Keep the regulator powered when PMIC transitions to STBY state. + type: boolean + + unevaluatedProperties: false + +additionalProperties: false diff --git a/sys/contrib/device-tree/Bindings/regulator/samsung,s2mpu05.yaml b/sys/contrib/device-tree/Bindings/regulator/samsung,s2mpu05.yaml new file mode 100644 index 000000000000..378518a5a7f5 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/regulator/samsung,s2mpu05.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/samsung,s2mpu05.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S2MPU05 Power Management IC regulators + +maintainers: + - Kaustabh Chakraborty <kauschluss@disroot.org> + +description: | + This is a part of device tree bindings for S2M and S5M family of Power + Management IC (PMIC). + + The S2MPU05 provides buck and LDO regulators. + + See also Documentation/devicetree/bindings/mfd/samsung,s2mps11.yaml for + additional information and example. + +patternProperties: + # 21 LDOs + "^ldo([1-9]|10|2[5-9]|3[0-5])$": + type: object + $ref: regulator.yaml# + unevaluatedProperties: false + description: + Properties for single LDO regulator. + + LDOs 11-24 are used for CP, and they're left unimplemented due to lack + of documentation on these regulators. + + required: + - regulator-name + + # 5 bucks + "^buck[1-5]$": + type: object + $ref: regulator.yaml# + unevaluatedProperties: false + description: + Properties for single buck regulator. + + required: + - regulator-name + +additionalProperties: false diff --git a/sys/contrib/device-tree/Bindings/regulator/sprd,sc2731-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/sprd,sc2731-regulator.yaml index ffb2924dde36..9bd752bab68e 100644 --- a/sys/contrib/device-tree/Bindings/regulator/sprd,sc2731-regulator.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/sprd,sc2731-regulator.yaml @@ -43,25 +43,4 @@ required: - compatible additionalProperties: false - -examples: - - | - regulators { - compatible = "sprd,sc2731-regulator"; - - BUCK_CPU0 { - regulator-name = "vddarm0"; - regulator-min-microvolt = <400000>; - regulator-max-microvolt = <1996875>; - regulator-ramp-delay = <25000>; - regulator-always-on; - }; - - LDO_CAMA0 { - regulator-name = "vddcama0"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <3750000>; - regulator-enable-ramp-delay = <100>; - }; - }; ... diff --git a/sys/contrib/device-tree/Bindings/regulator/ti,tps65219.yaml b/sys/contrib/device-tree/Bindings/regulator/ti,tps65219.yaml index 78e64521d401..7c64e588a8b5 100644 --- a/sys/contrib/device-tree/Bindings/regulator/ti,tps65219.yaml +++ b/sys/contrib/device-tree/Bindings/regulator/ti,tps65219.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/regulator/ti,tps65219.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: TI tps65219 Power Management Integrated Circuit regulators +title: TI TPS65214/TPS65215/TPS65219 Power Management Integrated Circuit maintainers: - Jerome Neanne <jerome.neanne@baylibre.com> @@ -12,9 +12,20 @@ maintainers: description: | Regulator nodes should be named to buck<number> and ldo<number>. + TI TPS65219 is a Power Management IC with 3 Buck regulators, 4 Low + Drop-out Regulators (LDOs), 1 GPIO, 2 GPOs, and power-button. + + TI TPS65215 is a derivative of TPS65219 with 3 Buck regulators, 2 Low + Drop-out Regulators (LDOs), 1 GPIO, 1 GPO, and power-button. + + TI TPS65214 is a derivative of TPS65219 with 3 Buck regulators, 2 Low + Drop-out Regulators (LDOs), 1 GPIO, 1 GPO, and power-button. + properties: compatible: enum: + - ti,tps65214 + - ti,tps65215 - ti,tps65219 reg: @@ -90,6 +101,20 @@ required: additionalProperties: false +allOf: + - if: + properties: + compatible: + contains: + enum: + - ti,tps65214 + - ti,tps65215 + then: + properties: + regulators: + patternProperties: + "^ldo[3-4]$": false + examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/sys/contrib/device-tree/Bindings/regulator/vctrl-regulator.yaml b/sys/contrib/device-tree/Bindings/regulator/vctrl-regulator.yaml new file mode 100644 index 000000000000..6132b8e5b498 --- /dev/null +++ b/sys/contrib/device-tree/Bindings/regulator/vctrl-regulator.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/vctrl-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Voltage controlled regulators + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +allOf: + - $ref: regulator.yaml# + +properties: + compatible: + const: vctrl-regulator + + ctrl-supply: + description: Regulator supplying the control voltage + + ctrl-voltage-range: + description: + Array of two integer values describing the range (min/max) of the + control voltage. The values specify the control voltage needed to + generate the corresponding regulator-min/max-microvolt output + voltage. + minItems: 2 + maxItems: 2 + $ref: /schemas/types.yaml#/definitions/uint32-array + + min-slew-down-rate: + description: + Describes how slowly the regulator voltage will decay down in the + worst case (lightest expected load). Specified in uV / us (like + main regulator ramp rate). This value is required when + ovp-threshold-percent is specified. + $ref: /schemas/types.yaml#/definitions/uint32 + + ovp-threshold-percent: + description: + Overvoltage protection (OVP) threshold of the regulator in percent. + Some regulators have an OVP circuitry which shuts down the regulator + when the actual output voltage deviates beyond a certain margin from + the expected value for a given control voltage. On larger voltage + decreases this can occur undesiredly since the output voltage does + not adjust immediately to changes in the control voltage. To avoid + this situation the vctrl driver breaks down larger voltage decreases + into multiple steps, where each step is within the OVP threshold. + minimum: 0 + maximum: 100 + +unevaluatedProperties: false + +dependencies: + ovp-threshold-percent: [ min-slew-down-rate ] + +required: + - compatible + - ctrl-supply + - ctrl-voltage-range + - regulator-min-microvolt + - regulator-max-microvolt + +examples: + - | + vctrl-reg { + compatible = "vctrl-regulator"; + regulator-name = "vctrl_reg"; + + ctrl-supply = <&ctrl_reg>; + ctrl-voltage-range = <200000 500000>; + + min-slew-down-rate = <225>; + ovp-threshold-percent = <16>; + + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1500000>; + }; +... |